Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
1216 E 5th St_BLD5684_2026
CITY OF ARLINGTON 18204 59th Avenue NE,Arlington,WA 98223 INSPECTIONS: 360-403-3417-Permit Center: 360-403-3551 BUILDING PERMIT 1216 E 5TH ST Permit#: 5684 PERMIT EXPIRES 180 DAYS AFTER Parcel#: 31051200200300 DATE OF ISSUANCE. Scope of Work: Install new fire alarm system in portable P 1 &P2.Tie new system Valuation:4800.00 to existing fire alarm system in school.Existing school fire alarm sequence of operation remain the same. OWNER APPLICANT CONTRACTOR ARLINGTON SCHOOL DISTRICT 16 Red Hawk Fire Protection 315 N FRENCH AVE 917 134th Ave SW Ste.B-3 ARLINGTON,WA 98223 Everett,WA 98204 , 253-330-0736 MECHANICAL CONTRACTOR PLUMBING CONTRACTOR LIC#: EXP: LIC#: EXP: JOB DESCRIPTION PERMIT TYPE: FIRE ALARM CODE YEAR: 2018 STORIES: 1 CONST.TYPE: IA DWELLING UNITS: OCC GROUP: E; Education BUILDINGS: OCC LOAD: PERMIT APPROVAL The issuance or granting of this permit shall not be construed to be a permit for,or approval of,any violation of this Code or any other ordinance or order of the City,of any state or federal law,or of any order,proclamation,guidance advice or decision of the Governor of this State.To the extent the issuance or granting of this permit is interpreted to allow construction activity during any period of time when such construction is prohibited or restricted by any state or federal law,or order,proclamation,guidance advice or decision of the Governor of this State,this permit shall not authorize such work and shall not be valid.The building official is authorized to prevent occupancy or use of a structure where in violation of this Code,any other City ordinances of this jurisdiction or any other ordinance or executive order of the City,or of any state or federal law,or of any order,proclamation, guidance advice or decision of the Governor.The building official is authorized to suspend or revoke this permit if it is determined to be issued in error or on the basis of incorrect,inaccurate or incomplete information,or in violation of any City ordinance,regulation or order,state or federal law,or any order,proclamation,guidance or decision of the Governor. I AGREE TO COMPLY WITH CITY AND STATE LAWS REGULATING CONSTRUCTION AND IN DOING THE WORK AUTHORIZED THEREBY;NO PERSON WILL BE EMPLOYED IN VIOLATION OF THE LABOR CODE OF THE STATE OF WASHINGTON RELATING TO WORKMEN'S COMPENSATION INSURANCE AND RCW 18.27. THIS APPLICATION IS NOT A PERMIT UNTIL SIGNED BY THE BUILDING OFFICIAL OR HIS/HER DEPUTY AND ALL FEES ARE PAID. IT IS UNLAWFUL TO USE OR OCCUPY A BUILDING OR STRUCTURE UNTIL A FINAL INSPECTION HAS BEEN MADE AND APPROVAL OR A CERTIFICATE OF OCCUPANCY HAS BEEN GRANTED.IBC 110/IRC 110. ,SALES TAX NOTICE: Sales tax relating to construction and construction materials in the City of Arlington must be reported on your sales tax return form and coded City of Arlington#3101. 11/20/2023,/ Applicant Signature Date Building Official Date CONDITIONS Approved job copy shall be onsite for inspections.Adhere to approved plans The property owner shall ensure that the construction project complies with all applicable zoning codes and regulations.The property owner shall also ensure that the construction project does not cause any adverse impact on the surrounding environment or community.The property owner shall be responsible for obtaining all necessary permits and approvals from the relevant authorities before commencing construction.The property owner shall ensure that the construction project complies with all applicable design review requirements. THIS PERMIT AUTHORIZES ONLY THE WORK NOTED.THIS PERMIT COVERS WORK TO BE DONE ON PRIVATE PROPERTY ONLY.ANY CONSTRUCTION ON THE PUBLIC DOMAIN(CURBS, SIDEWALKS,DRIVEWAYS, MARQUEES,ETC.)WILL REQUIRE SEPARATE PERMISSION. PERMIT FEES Date Description Fee Amount 11/20/2023 Web Only-Fire System Plan Review $200.00 11/20/2023 Processing/Technology $25.00 11/20/2023 FACP/Transmitter-New $200.00 11/20/2023 FACP/Transmitter-Replace $125.00 11/20/2023 Fire Alarm System Permit $375.00 11/20/2023 Credit Card Service $6.00 Total Due: $931.00 Total Payment: $206.00 Balance Due: $725.00 CALL FOR INSPECTIONS Call by 3:30 pm for next day inspection,allow 48 hours for Fire Inspections When calling for an inspection please leave the following information: Permit Number,Type of Inspection being requested,and whether you prefer morning or afternoon INSPECTION INFORMATION Pass/Fail CITY OF ARLINGTON e 18204 59th Avenue NE,Arlington,WA 98223 INSPECTIONS: 360-403-3417- Pennit Center: 360-403-3551 BUILDING PERNIIT 1216 E STH ST Permit#:5684 Parcel#: 31051200200300 PERMIT EXPIRES 180 DAYS AFTER DATE OF ISSUANCE. Scope of Work: Install new fire alarm system in portable PI &P2.Tie new system Valuation:4800.00 to existing fire alarm system in school.Existing school fire alarm sequence of operation remain the same. OWNER APPLICANT CONTRACTOR ARLINGTON SCHOOL DISTRICT 16 Red Hawk Fire Protection 315 N FRENCH AVE 917 134th Ave SW Ste.B-3 ARLINGTON,WA 98223 Everett,WA 98204 , 253-330-0736 MECHANICAL CONTRACTOR PLUMBING CONTRACTOR LIC#: EXP: LIC#: EXP: JOB DESCRIPTION PERMIT TYPE: FIRE ALARM CODE YEAR: 2018 STORIES: 1 CONST.TYPE: IA DWELLING UNITS: OCC GROUP: E; Education BUILDINGS: OCC LOAD: PERMIT APPROVAL The issuance or granting of this permit shall not be construed to be a permit for,or approval of,any violation of this Code or any other ordinance or order of the City,of any state or federal law,or of any order,proclamation,guidance advice or decision of the Governor of this State.To the extent the issuance or granting of this permit is interpreted to allow construction activity during any period of time when such construction is prohibited or restricted by any state or federal law,or order,proclamation,guidance advice or decision of the Governor of this State,this permit shall not authorize such work and shall not be valid.The building official is authorized to prevent occupancy or use of a structure where in violation of this Code,any other City ordinances of this jurisdiction or any other ordinance or executive order of the City,or of any state or federal law,or of any order,proclamation, guidance advice or decision of the Governor.The building official is authorized to suspend or revoke this permit if it is determined to be issued in error or on the basis of incorrect,inaccurate or incomplete information,or in violation of any City ordinance,regulation or order,state or federal law,or any order.proclamation,guidance or decision of the Governor. l AGREF.TO COMPLY WITH CITY AND STATE LAWS REGULATING CONSTRUCTION AND IN DOING THE WORK AUTHORIZED THEREBY;NO PERSON WILL BE EMPLOYED IN VIOLATION OF THE LABOR CODE OF THE STATE OF WASHINGTON RELATING TO WORKMEN'S COMPENSATION INSURANCE AND RCW 18.27. THIS APPLICATION IS NOT A PERMIT UNTIL SIGNED BY THE BUILDING OFFICIAL OR HIS/HER DEPUTY AND ALL FEES ARE PAID. IT IS UNLAWFUL TO USE OR OCCUPY A BUILDING OR STRUCTURE UNTIL A FINAL INSPECTION HAS BEEN MADE AND APPROVAL OR A CERTIFICATE OF OCCUPANCY HAS BEEN GRANTED.IBC 1 I O/IRC 110. SALES TAX NOI'I!C.E: Sales tax relating to construction and construction materials in the City of Arlington must be reported on your sales tax return form and coded City of Arlington#3101. I t 2I 4-r-2 3 � �G � 11/20/2023.i Applicant Signature Date Building Official Date CONDITIONS Approved job copy shall be onsite for inspections.Adhere to approved plans The property owner shall ensure that the construction project complies with all applicable zoning codes and regulations. The property owner shall also ensure that the construction project does not cause any adverse impact on the surrounding environment or community.The property owner shall be responsible for obtaining all necessary permits and approvals from the relevant authorities before commencing construction. The property owner shall ensure that the construction project complies with all applicable design review requirements. THIS PERMIT AUTHORIZES ONLY THE WORK NOTED.THIS PERMIT COVERS WORK TO BE DONE ON PRIVATE PROPERTY ONLY.ANY CONSTRUCTION ON THE PUBLIC DOMAIN (CURBS, SIDEWALKS,DRIVEWAYS, MARQUEES,ETC.)WILL REQUIRE SEPARATE PERMISSION. PERMIT FEES Date Description Fee Amount 11120/2023 Web Only- Fire System Plan Review $200.00 11/20/2023 Processing/Technology $25.00 1112012023 FACP 1 Transmitter-New $200.00 11/20/2023 PACP 1 Transmitter-Replace $125.00 11/20/2023 Fire Alarm System Permit $375.00 11/20/2023 Credit Card Service $6.00 Total Due: $931.00 Total Payment: $206.00 Balance Due: $725.00 CALL FOR INSPECTIONS Call by 3:30 pm for next day inspection, allow 48 hours for Fire Inspections When calling for an inspection please leave the following information: Permit Number,Type of Inspection being requested,and whether you prefer morning or afternoon INSPECTION INFORMATION Pass/Fail i FIRE ALARM PERMIT APPLICATION • Community and Economic Development City of Arlington• 18204 59th Ave NE•Arlington,WA 98223 • Phone(360) 403-3551 Type of Permit: ❑ New Installation ✓❑ System Modification Phased Installation 1216 E.5th St.Arlington WA Property Address: 98223 Suite No.: P1 & P2 project Valuation: $4800 Lot#: Parcel ID No.: 31051200200300 Preferred Contact: 13 Owner 0 Applicant 71 Contractor Project Description: Install new fire alarm system in portable P1 &P2. Tie new system to existing fire alarm system in school. Existing school fire alarm sequence of operation remain the same. School evac on general alarm. Owner Name: Eagle Creek Elem School, Arlington School District phone No.: 360.618.6270 Email Address: Cell No.: Mailing Address: 1216 East 5th Street City: Arlington State: WA Zip: 98223 Applicant Name: James Pan Phone No.: Email Address: jamesp@redhawkfp.com Cell No.: 253-330-0736 Mailing Address: 917 134th Ave SW Ste. B-3 City: Everett State: WA Zip: 98204 Contractor Name: Red Hawk Fire Protection Phone No.: (425) 818-3313 Email Address: Cell No.: Mailing Address: 917 134th Ave SW Ste. B-3 City: Everett State: WA Zip: 98204 L&I Contractor License Number: REDHAHF901QP Expiration Date: 11/17/2024 SUBMITTAL REQUIREMENTS: Provide Information on All Equipment to be Installed Prior to Installation Submit electronic files of the follow: 0 Complete and Scaled Plans 0 Specification Sheets 0 Wiring Diagrams (Point to Point Wiring) ❑ Electrical Plans,if applicable NOTE: All Central Station Monitoring must be UL or FM listed. FIRE ALARM SYSTEMS (105.7.3) ** DEVICES include separate individual portions of a Fire Alarm System such as: Initiating Devices, Notification Appliances, Flow Switch, Supervisory Switches, Magnetic Door Hold-Open Devices, Remote Annunciators, Pull Stations, Beam Detectors, and other such devices. (Each piece is one device) PLAN REVIEW FEES -shall be paid at time of application submittal Less than $5,000.00 = $100.00 $5,000.00 &over—based on project valuation (Plan Review Fee is 65%of project valuation per Fee Calculation Table 4-1) REV2022 Page 1 of 2 REINSPECTION / PHASED INSTALLATION INSPECTIONS Submit Phasing Plan with Application - review and approval required REINSPECTION FEES SHALL BE PAID PRIOR TO INSPECTION FEE Reinspection/Phased Installation fee is charged per hour (1 hour minimum) $75.00 ✓0 TENANT IMPROVEMENT OR SYSTEM MODIFICATION (NFPA 72) Number of Devices" Device Fee Subtotal 1to2 $ 75.00 = $ 3 to 5 $125.00 = $ 6 to 10 $175.00 = $ 11 to 20 $225.00 = $ 21 to 40 $300.00 = $ 41 to 100 $375.00 = $ 375 101 to 200 $475.00 = $ > 200 $500.00 plus$50.00 per 100 additional devices(round up) Total Number of Devices = $500.00 + $ _ $ FACP/TRANSMITTER Modification $125.00 = $ 125 PERMIT FEE SUBTOTAL $ 500 ❑ NEW COMMERCIAL SYSTEM (NFPA 72) Number of Devices" Device Fee Subtotal 1 to 100 $350.00 = $ 101 to 200 $475.00 = $ > 200 $500.00 plus$50.00 per 100 additional devices(round up) Total Number of Devices = $500.00 + $ _ $ FACP/TRANSMITTER New $200.00 = $ 200 PERMIT FEE SUBTOTAL $ 200 PERMIT FEE TOTAL $ 700 PLAN REVIEW FEE $ 100 Processing/Technology Fee $25.00 TOTAL $ 825 I hereby certify that I am the ❑ Owner, 0 Applicant, 0 Contractor,and authorized to sign this application and that the above information is correct and construction on, and the occupancy and the use of the above-described property will be in accordance with the laws,rules and regulation of the State of Washington,and the City of Arlington. Digitally signed by James Pan James PanDNC=US En,OU=p@retManper, =JRedHawk James Pan 1103/2023 Fire Protection,OU=Project Manager,CN=James Pan Date:2023.11.03 135454-07'00' Signature Print Name Date SAVE PRINT REV2022 Page 2 of 2 2 3 4 5 6 7 8 9 EAGLE CREEK ES PORTABLE # 1 A ARLINGTON SCHOOL DISTRICT A FIRE ALARM SYSTEM 1216 E 5TH STREET, ARLINGTON, WA 98223 SYMBOL LEGEND DEVICE DESIGNATION LEGEND: INSTALLATION&GENERAL WIRING NOTES: SYMBOL&WIRE STYLE IDENTIFICATION SYMBOL QTY DESCRIPTION MOUNTING REQUIREMENTS SUPPLIER PART NUMBER FACP 1 ADDRESSABLE FIRE ALARM CONTROL PANEL PART INCLUDES ENCLOSURE;MOUNT AT 72"TO TOP NOTIFIED NFW-50X NOTIFIER ONYX SERIES ADDRESSABLE INITIATING DEVICES: "INERAI INSTALLATION SHALL BE ACCOMPLISHED IN STRICT COMPLIANCE WITH NFPA,LOCAL AND STATE J-BOX 2C,D WIRFICABLE INDENTIFIER AHJ's,NEC AND CONTRACT DRAWINGS 2C-2TT CCABLES CAENS INTELLIGENT PHOTO SMOKE DETECTOR 4 SQUARE DEEP w/3"ROUND RING D=11VPE9'fIBIE EDP 4 NOTIFIED FSP-951 w/8300-6 2. WIRE ROUTING IS DIAGRAMMATIC IN NATURE ONLY AND NOT INTENDED FOR ACTUAL CONDUIT � S� MAC) ROUTING. CABLE INSTALLATION TYPES INTELLIGENT MANUAL PULL STATION 4 SQUARE DEEP w/1 GANG RING;MOUNTED AT 48"TO TOP NBG-12LX THE DETECTOR&MODULES ON 2.1. WIRING SHOWN GOING'THRU"A DEVICE DOES NOT NEED TO TERMINATE AT THAT DEVICE IF OPg1� RACII 0 4 NOTIFIER W/STI-1130 ONYXSENIESMAY161VE DEVICE IS NOT ON THAT CIRCUIT. THE SAME FELDADDRESS 21.1. MEANING VOICE,STROBE/NAC CIRCUITS DO NOT NEED TO PASS THRU SLC DEVICES M 2INTELLIGENT MONITOR MODULE 4 SQUARE DEEP NOTIFIER FMM-1 D FOR EIMM D &SLC CIRCUITS DO NOT NEED TO PASS THRU NOTIFICATION DEVICES.POWER S��-���-�4 DEMO OR REMOVE EQUIPMENT FROM SERVICE E'IE tale ' A r, A ,g CIRCUITS ONLY NEED TO GO FROM POWERED DEVICE TO POWERED DEVICE. RACEWAY REQUIRED TO BE INSTALLEDUTILVJNG HEAT DETECTOR:194'FIXED TEMP&RATE OF RISE 4 SQUARE DEEP w/3"ROUND RING FSS�' 12 tp' -27-�-IM-"' 3. ALL CONDUIT SIZING AND ROUTING BY ELECTRICAL CONTRACTOR PER NEC AND ANJ. -zHR----zHR-j 1 d3 NEC APPROVED 2HR METHODS OF PROTECTION B B OH ism 4 NOTIFIED 5602 w4. VERIFY ALL LOCATIONS OF DEVICES WITH ELLCIRICAL/ARCHITECTURAL PLANS. SCALE AND PLACE 120VAC VOLTAGE PROTECTOR for CONTROL PANELS MOUNTS IN 1/2"OR 3/4"CABINET KNOCKOUT w a, ALLDEVICE PER ELECTRICAL/ARCHITECTURAL PLANS. �- -- -- --S ACPOWER(120,240Or480VAC) 1 $PACEAGE E120V-GT e' aw w 5. ALL CIRCUITS WILL BE PROPERLY TAGGED AND TESTED FOR OPENS,SHORTS,GROUNDS AND __w/LOCKOUT&LABELS xw PROPER"END-OF-LINE'RESISTANCE. EACH CIRCUITS METER READING MUST BE DOCUMENTED �fENLARGEDVIEWBOUNDRY 24VDC SURGE SUPPRESSOR;2PR,14-30VDC,16-22AWC 4 SQUARE DEEP a a \\/)� 1 AND PRESENTED TO FIELD TECHNICAJ UPON ARRIVAL ONSITE FOR STARTUP&CHECKOUT. �TOP LINE INDICATES THEDETAII BOTTOM WALL HORN w/STROBE:WHITE 4 SQUARE DEEP;MOUNTED AT 80"TO BOTTOM a w° a nF52 30�0-1699p +?t59 w"';2 Loaf 6 6.2. BUASUBUILTSHSHALLLLBEOPKEPT ORDERLYDAANDEBE�C FOR LOEAR YSMARKEDCWITHCDIFFERENOTNCOLORR - 1xx---J aNEINDICATESTHESHEET& LI 2 SEE DEVICE DESIGNATION FOR STROBE Cd SETTING SYSTEM T SENSOR P W2MHLP24FWH I0 Loll __-__J -TOM' WALL STROBE.WHITE 4 SQUARE DEEP,MOUNTED AT 80'TO BOTTOM NOTIFICATION APPLIANCES: PENS FOR EACH CIRCUIT AND/OR CIRCUIT TYPE. AS-BUILTS MUST INDICATE CHANGES TO i g "' ATC 2 SEE ONCE DESIGNATION FOR STROBE Call SETTING SYSTEM SENSOR SWL THE FINAL DEVICE INSTALLED LOCATIONS IF NOT INSTALLED AT LOCATION SHOWN ON ENDdLINERESISTMI SBATIONDETAL CEILING INFO DESIGN DOCUMENTS. _ v� ----------- 1 *------------ WALL HORN VI STROBE:RED:WEATHERPROOF SA-W13B BACK BOX:SURFACE MOUNT AT 80°TO BOTTOM '1 ? '1 9 ',1 6.3. AS-BUILT REDLINES NOT PROVIDING THIS INFORMATION WILL BE RETURNED TO THE 0 a i ' SEE DEVICE DESIGNATION FOR STROBE cd SETTING SYSTEM SENSOR P2RK INSTALLATION CONTRACTOR FOR CORRECTION. NOTES: 7. AGREEMENT AND CONFIRMATION OF ALL MILESTONE EVENTS WILL BE MADE WITH PROJECT FLAG NOTE SHEEfNOIE EQUIPMENT MANAGER. - -- ZONEBOUNDWES ---- NOTE:--- 1 -----J 1-ONCE SUBSCRIPT: NW=NEW RR-REMOVE&RELOCATE EX=EXISTING TO REMAIN AC-ABOVE CEILING RB=RELAY BASE WP=WATERPROOF WG=WIRE GUARD ISo-ISO BASE Sly LF'WJNDEk /3.Dp01LY: BELL DFS%kTHM6 8. ALL FIELD SERVICES MUST BE SCHEDULED WITH PROJECT MANAGER WITH A MINIMUM OF 14 1s=15m N=#sm 1sD=153oa Lob=tam M=1NHpN 6=s'BFu _ADAROOM,AREA OR FULLHeIGHTWALL 2-CABLEING SHOWN IS FOR CIRCUIT REFERENCE ONLY AND DOES NOT INTENDED TO INDICATE THE EXACT PATHWAY. 3D=3Dod 110=11N#I7r=17rm LSD=150m H=HONOFLY 8=111EIL WORKING DAYS ADVANCE NOTICE. 3-DEVICES SHOWN ON DRAWINGS IN GRAY SCALE ARE EXISTING DEVICES AND MAY NOT BE INCLUDED IN THIS SYMBOL LEGEND UNLESS NOTED. N=91m 118=11&d 1p=185m DT=177m hSPF11f9tOFLY 10=10 BELL 9. DO NOT INSTALL ONE VOLTAGE IN SAME CONDUIT AS POWER LIMITED CABLES. _ - 75=Ism t36=t3M L85=1Nc1 LF=LOWREAUBIOY ?BELL -2HR RATED WALL PARTIALHFJGNIWALL 4-SET HORN/STROBE DECIBLE SETTING TO LOW FROM FACTORY SETTING OF HIGH,ONLESS OTHERWISE NOTED ON THE DRAWINGS. III A'APQ14CENFTO THE DEVINDICATESTFNTTFEDEVICEM0 MRATED FIRE ALARM SPECIFIC NOTES: --1HR RATED WALL 5-All DEVICES WITH A WP SUBSCRIPT WILL REWIRE THE USE OF OUTDOOR OR WP BACKBOK NOTIFICATION VISUAL CIRCUITS: 1. SMOKE DETECTORS SHALL NOT BE INSTALLED WITHIN 36"OF ANY AIR DIFFUSER. ROORTHATP86CN 2. 2019 HER72-17.7.1.12.3 REQUIRES THAT SMOKE DETECTORS SHALL NOT BE INSTALLED UNTIL CIRCUITTYPE: AFTER FINAL CONSTRUCTION CLEAN-UP. C 'C=FACP HAG CIRCUIT pgpLgpppLyp 2.1. ANY SMOKE DETECTORS THAT HAVE BEEN INSTALLED PRIOR TO CLEAN-UP MUST BE C x=AlSNACCIRCUIT CLEANED OR REPLACED AND WILL BE INVOICED ON A T&M BASIS. r-24VOC POWER CIRCUIT 9UBgRCIIrxuMBER SITE MAP: TH'=24VDC RESET POWER CIRCUIT 3, WALL MOUNTED NOTIFICATION DEVICES BACKER BETWEEN A MINIMUM OF 80"WE TO A MAXIMUM FLAGNDTES v'-VOICErs TROBE C1PPAp�CIRaIIT RIA2 ODASIETE of ss"AFT NOTE DESCRIPTION T=A3.DIORTSER cIxcuR N 1 A -O CKU1T# 3.1. DEVICES THAT ARE UNABLE TO BE MOUNTED WITHIN THAT RANGE MUST BE VERIFIED PRIOR TO INSTALLATION. 1 25 PROMDE HINGED PLASTIC COVER FOR FIRE ALARM MANUAL PULL STATION(TYP.) 3.2. SEE FLOOR PLANS FOR CANDELA RATING of EACH DEVICE INSTALLED. SYSEMSENSORHOPo45&LIMES AUDIO SELECTOR WIE80D(110fNS - 'L'SERIESDEVTCES MMED61S61 DENIES 4. ALL MANUAL PULL STATIONS ARE TO BE MOUNTED AT A HEIGHT NO GREATER THAN 48'TO TOP e AND NO LOWER THAN 36'TO BOTTOM(PER ADA REQUIREMENTS). WORT f 5. FIELD VERIFY ALL SPRINKLER MONITORING DEVICES WITH FIRE PROTECTION CONTRACTOR _ WIRE LEGEND 6. FIELD VERIFY ALL WAC FAN CONTROL FIRE/SMOKE DAMPERS AND DUCT DETECTORS LOCATIONS _ ❑ SYMBOL DESCRIPTION PENN FPL FPLP WET COLOR CODING CIRCUIT TYPE NOTES me.En,;�a, r:..E.� WITH MECHANICAL CONTRACTOR - M °o ^ ,__ Txnz non-mxv -s<onoN e a 7. FACE SHALL NOT BE ENERGIZED WITHOUT THE PRESENCE OF TECHNICIANS. _aI _ A 1 PAIR 16AWG FIRE RATED CABLE YES 971 80991B AQ225 CONVENTIONAL(IDC)CIRCUIT a.ww TOM uortima ssauo wumv a 8. NO TAPPING OF SIGNALING OR INITIATING ZONE CIRCUITS ARE ALLOWED. T-TAPPING OF STYLE 4 - Wpp roi n.- raR AfRRmCf n�"T ONa CaN 9E nfW WdUSRa AT iHE.W AEOUE51 CD C 1 PAIR 14AWC FIRE RATED CABLE IS 972 60993E AQ226 AUDIBLE(NAC)CIRCUIT ADDRESSABLE CIRCUITS IS ALLOWED PROVIDING A SPLICE IS PROFESSIONALLY INSTALLED, _ - D 1 PAIR 16AWG FIRE RATED CABLE --- 971 60991B AQ225 DATA(SLC)CIRCUIT POLARITY IS OBSERVED AND SHIELDS ARE CONTINUOUS AND FREE OF GROUNDS. SHIELDS MUST ❑ BE TERMINATED AT FACE ONLY. MAIN BLDG FACE NOTES: 8.1. CABLE SHIELDS SHALL BE SPLICED TOGETHER AT EVERY JUNCTION BETWEEN THE FACP ww DIFFERENT COLORS/STRIPE COMBINATIONS TO BE USED FOR DIFFERENT CIRCUIT TYPES.LABEL ALL CIRCUITS ACCORDINGLY AND THE LAST DEVICE ON EACH CABLE RUN. SHIELDS AND OTHER FIRE ALARM 1-WIRE MANUFACTURER IS FOR REFERENCE PURPOSE ONLY. WHEN USING OTHER MANUFACTURE,ENSURE PROPER CROSS REFERENCE SCOPE OF WORK&DESIGN BASIS CONDUCTORS(EXCEPT POWER GROUNDS)SHALL BE INSULATED AND COMPLETELY FREE 2-FPLP CAN BE USED IN MOST ALL APPLICATIONS WITH THE EXCLUSION OF WET AND CIRCUIT INTEGRITY REQUIREMENTS FROM CONDUIT OR EARTH GROUNDS. SHIELDS WILL BE TIES TO GROUND ONLY AT THE P FIRE ALARM SYSTEM FOR NEWLY ADDED PORTABLE BUILDINGS.NEW NOTIFICATION,INITIATION AND DETECTION FACE BY THE FIELD TECHNICIAN. AREA OF ORK 3-INSTALL WIRING PER NEC. USE CABLE TYPE CONSISTENT WITH NEC REQUIREMENTS,IE:PLENUM,RISER,UNDERGROUND,ETC. DEVICES TO BE INSTALLED.NOTIFICATION WILL BE POWERED BY FACE IN PORTABLE.EXISTING SEQUENCE OF 9. THE SYSTEM SHALL BE MONITORED BY A U.L.LISTED MONITORING STATION BEFORE AHJ TEST. OPERATIONS TO REMAIN IN PLACE AND UNCHANGED.AREAS OF WORK SHOWN IN THESE DRAWINGS ARE ONLY 10, AS-BUILTS ARE REQUIRED AT TIME OF AHJ ACCEPTANCE.REQUIRED ELECTRICAL RED LINES 9 0 4-THE°A FIBER OPTIC CABLE LISTED IS A N ELUEN CABLE PART NUMBER AS WEST PENN NO LONGER SUPPORTS FIBER OPTIC CABLE AREAS WITHIN SCOPE.NEW FACP TO BE MONITORED BY MAIN FACE IN MAIN BUILDING. WITHIN 2 WEEKS PRIOR TO AHJ TESTS. PORTABLE FRCP Pz p 5-THIS CABLE MUST BE INSTALLED IN A CONTINUOUS PATH POINT-TO-POINT. ABSOLUTLEY NO SPLICES ARE ALLOWED. 10.1. EACH CIRCUIT(SLC,NAC OR POWER)TO BE CLEARLY IDENTIFIED WITH A DISTINCT COLOR 6-THIS IS A SPECIFIC CABLE,NO ALTERNATES ARE ALLOWED 10.2. EACH NAC CIRCUIT MUST BE CLEARLY MARKED AS TO WHICH DEVICES ARE ON EACH CIRCUIT AND IN THE ORDER THE DEVICES ARE WIRED TO COMPLETE THE CIRCUIT, FACP Battery Load&Back-up Calculation FACP NAC Circuit Load, Voltage Drop &Battery Load Calculations FACP Control Panel: FACP APS Name: FACP P1 P2 Location: PORTABLE P1 Location: PORTABLE P1 Standby. Alarm: Output 11 Output I2 Output I3 Output 14 Output I5 Output I6 Output I7 Aux FACP Type: NFW-5OX(FACP) Each Each Total Total P.S.Type: NFW-50X(FACP) 0.1410 0.2570 Visual Visual Not Used Not Used Not Used Not Used Nat Used Power Line# Qty Part I: Description: Standby Alarm Standby Alarm Part I: Description: Ni INSX-X X-X X-X X-X X-X X-X Total Oty 1 1 NFW-50X Fire Alarm Control Panel:1 SLC Loop,50 SLC Devices,Black Enclosure 0.2570 0.2570 0.2570 0.2570 SWL(15) Wall Strobe set at 15cd 0.0000 0.0430 2 2 4 2 4 FSP-951 Intelligent Photoelectric Smoke Detector:White 0.0002 0.0045 0.0008 0.0180 PAL(185) Wall Horn w/Strobe set at 185cd 0 O HEX[.0000 0.2450 2 2 4 0 OO PORTABLE 3 4 B30�6 Intelligent Detector Base:Mite 0.0000 00000 O.W00 O.OWO P2YM 75 Wall Ham w Strobe set at 75cd,WP 0.0000 01760 1 1 2 5BT D OD6 D 007 D 4 4 NBG-12LX Addressable Manual Pull Station OOD04 OB050 00015 0.0200 I Devices per Circuit: 5 5 0 0 0 0 0 0 10 R12AC 5 4 FMM-1 Addressable Monitor Module 0.0004 0,0050 0.0016 0.0200 Total Standby Circuit Call Amps(3): COO) 0.WO 0.000 0000 0.WO 0.000 0.000 0.0000 0.1410 85 r-DW A NI-5 C NI-4 A 6 4 5602 194'Heal Detector Fixed&BUR Tempalure 0.0000 0.0000 0.0000 0.0000 Total Alarm Circuit Calculated Amps UT 0.752 0.752 0.0(10 0,000 0.000 Ol 0.000 0.0000 0.2570 1 CD 004 IN 15 15 008 IM H7 4 P2WL(185) Wall Harn n/Strobe set at 185cd COCOO 0.2450 0.0000 0.9800 Wire Gauge Used(awg): 14AWG 14AWG 14AWG 14AWG 14AW'G 14AWG 14AWG 14AW'G Total , neAc8 4 SWL(15) WaII Strobe set at I5cd I G000.0430 0.0000 0.1720 Circuit Length(RT 85 115 0 0 0 0 0 0 Amps9 2 P2WR 75 WaII Harn w Strobe set at 75ed,WP 0.0W0 0.1760 0.0000 0.3520 Estimated Voltage Drop(do): 0.33 0.45 OR 0.00 0.00 DDO 0.00 0.00 RequiredD ® D A Total Current Once, 0.2609 1.8190 005 ppgD Estiated EOL Valtage(do): 23.67 23.55 24.G0 24DO 2400 24.G0 24.00 2400 1.504E Calculated Voltage Drop k 1.4% 1.9% O.oX OD% 0.0% 0.0% 0B% 0.0% P A P E BATTERY LOAD CALC for FACP: FACP Max P.S.Rating: 2 Total Amps Required: 1.819 %Used: 73% To MIA N C 1)Current Draw Measurement based on:U.1971,16-33V,DC,High db&Temporal Patten BLDG FACP 1B 1A A Hours Standby 24 Total Standby Current: 0.2609 Total Amp Hours Required(AH): 6.3 2)Some DotalDevices have the same Measured Current Draw as the Indoor Devices and may not listed separately above. Minutes Ale. 5 Total Alarm Current L8190 Total Amp Minutes Required(AH): 0.2 3)When the APS is configured for'Doors*,Output 14 shutsdown on loss of AC Power. Therefore no'Standby Current Draw is shown nc H F 001 010 F Backup Generates? Wknawn Minimum Battery Size Needed(All 6A BATTERY LOAD CALC for FACP: NAC P.S.Max Rating: 2.500 Total Amps Required: 1.504 %Used: 607 NI- 1-3 Voice Ewcucation? Na Spare Circuit Capacity 20% Spore Battery Capacity Required: 1.3 CD 25 8 25 MDitary? I Na Spare Battery Load Facturl 20% Actual Battery Size Required(AH): 7.7 Hours Standby 24 Total Standby Current 0.1410 Total Hours Required fa Standby(AH):F 3.4 00 F F 003 Minutes Alsmn: 5 Total Alarm Cumt:l 17610 Total Hours Required for Alarm(AHB:I 01 75 W MAXIMUM CHARGER CAPACITY IS: 18 All Total AH Rated Batteries Supplied:= 18.0 Backup Generator? Onknowm Minimum Battery Size Needed(AH): 3.5 Voice E aaaa,an? No Gpae Giraait Capacty 2G% Spare Battery CopocOr Required 0, ,PORTABLE P1 FIRE ALARM LAYOUT Militar}? No Spare Batlay Load Factor. 20% Actual Battery Size Required(All 4.2 1 SCALE:1/8"=1'-0" MA%]MUM CHARGER CAPACITY IS: 18AH Total AH Rated Batteries Supplied: ev °ATE. DESCRIPTION: °RAWN6Y:APPR°VBY: CLIENT: N.I.C.E.T. CERTIFICATION nwnaSDF ioi25/2023 EAGLE CREEK ES PORTABLE O10/ 2023 SUBMITTAL DRAWINGS SDF SF �\ RED HAWK on Iv021ozizozi SUBMITTAL DRAWINGS(CHANGED ADDRESSES) SIDE MS STATEMENT sEaSDF all/02/2023 ARLINGTON SCHOOL DISTRICT F �E FIR ALARM R ecT nNw am 1216 E 5TH STREET F THESE SWINGS HAVE FIRE i'ROTECTION ARLINGTON,WA 98223 BEEN RENEWED BY: M1� REgpR ,ecT ENaINeeR. FIRE ALARM SYSTEM FIRE PROTECTION ENGINEERING 1.- a . EVei` E 1 EET TECHNOLOGY $4�'ALE'i - -0 eT om ee rw Ir. e. - BEET - e FIRE AIARM SYSTEMS-LEVEL II 16 8 6 4 2 0 FA-1.00 NICIT CERTIFICATION�101008 ^ n n TENT. E. CERTIHCATION EXPIRES-NAl1lL024 PROJECT#: 1 2 3 4 5 6 7 8 9 2 3 4 5 6 7 8 9 EAGLE CREEK ES PORTABLE #2 A ARLINGTON SCHOOL DISTRICT A FIRE ALARM SYSTEM 1216 E 5TH STREET, ARLINGTON, WA 98223 SYMBOL LEGEND DEVICE DESIGNATION LEGEND: INSTALLATION&GENERAL WIRING NOTES: SYMBOL&WIRE STYLE IDENTIFICATION SYMBOL CITY DESCRIPTION MOUNTING REQUIREMENTS SUPPLIER PART NUMBER INTELLIGENT PHOTO SMOKE DETECTOR 4 SQUARE DEEP w/3"ROUND RING CF.>p 4 NOTIFIER FSP-951 w/6300-6 NOTIFIER ONYX SERIES ADDRESSABLE INITIATING DEVICES: 1. INsrALAnoN SHALL BE AccoMPuSHED IN STRICT coMPLwNCE went NFPA,Loco AND STATE J-BOXY zc,D WIRFICA9LE ICABLES FIE' AHJ's,NEC AND CONTRACT DRAWINGS 2C-2TYEV CALES INTELLIGENT MANUAL PULL STATION 4 SQUARE DEEP w/1 GANG RING;MOUNTED AT 48"TO TOP NBG-12LX D'11VPE9'Gt&E ❑F 4 NOTIFIER W/STI-1130 I I 2 OU TIN OUTING IS DIAGRAMMATIC IN NATURE ONLY AND NOT INTENDED FOR ACTUAL CONDUIT INTELLIGENT MONITOR MODULE 4 SQUARE DEEP LASE IOADDRE55 THE DETECTOR&MODULES ON 2.1. WIRING SHOWN GOING'THRU"A DEVICE DOES NOT NEED TO TERMINATE AT THAT DEVICE IF CABLE INSTALLATION TYPES 311 2 NOTIFIER FMM-1 OEIECTORaMOWLE ONYIISERIES MAY1lAVE DEVICE IS NOT ON THAT CIRCUIT. THE SAME FIELD ADDRESS 21.1. MEANING VOICE,STROBE/NAC CIRCUITS DO NOT NEED TO PASS THRU SLC DEVICES x ©gym 4 HEAT DETECTOR:194'FIXED TEMP&RATE OF RISE 4 SQUARE DEEP w/3"ROUND RING NOTIFIER 5602 IDOPMTMBERISLC) D FORDOAIPIJ: D &SLC CIRCUITS DO NOT NEED TO PASS THRU NOTIFICATION DEVICES.POWER - I"-C-4 DEMO OR REMOVE EQUIPMENT FROM SERVICE COLFLEIE I* , A r-. A ,l CIRCUITS ONLY NEED To GO FROM POWERED DEVICE TO POWERED DEVICE. RACEWAY REQUIRED TO BE INSTALLEDUTIL0NG B 24WC SURGE SUPPRESSOR;2PR,14-30WC,i6-22AWG 4 SQUARE DEEP DEVICEA%NE33 12 Ip' 27- -IM-' 3. ALL CONDUIT SIZING AND ROUTING BY ELECTRICAL CONTRACTOR PER NEC AND AHJ. -2HR----2HR-j 1d3 NEC APPROVED 2HR METHODS OFPROTECTION B ❑ss 1 DITEK DTK-2MHLP24FW8 a 4. VERIFY All LOCATIONS OF DEVICES WITH ELECTRICAL/ARCHITECTURAL PLANS. SCALE AND PLACE WALL HORN w/STROBE:WHITE 4 SQUARE DEEP;MOUNTED AT 80"TO BOTTOM w e° ALL DEVICE PER ELECTRICAL/ARCHITECTURAL PLANS. �- -- -- --S AC POWER(120,240 Or480VAC) 2 SYSTEM SENSOR PAL A' rw 5. ALL CIRCUITS WILL BE PROPERLY TAGGED AND TESTED FOR OPENS,SHORTS,GROUNDS AND ' SEE BINGE DESIGNATION FOR STROBE cd SETTING ` ° PROPER"END RESISTANCE EACH CIRCUITS METER READING MUST BE DOCUMENTED i- �fENLARGEDVIEWBOUNDRY WALL STROBE:WHITE 4 SQUARE DEEP;MOUNTED AT 80"TO BOTTOM e AND PRESENTED TO FIELD TECHNICIAN UPON ARRIVAL ONSITE FOR STARTUP&CHECKOUT. X ��TOP LINE INDICATES THE OETAILp AS- WALL HORN w/STROBE RED:WEATHERPROOF SETTING SA-W13B BACK BOX:SURFACE MOUNT AT 80"TO BOTTOM Ialmwrmaemwra = ens w° °� uFsi-sio_is9 DOGG:is9 MOB I2 ioa�rl} 6 61 BURA SET OF OUTES SHALL iBLE KEPT BY PRQIECTAWOREMAN"�OR USE BY CONDUIT AND CONDUCTOR __ - --J BOTTOM DNEINDICATFSTHESHEET& 2 SYSTEM SENSOR SWL } 6.2. AS-BUILTS SHALL BE KEPT ORDERLY AND BE CLEARLY MARKED WITH DIFFERENT COLOR ` _ J ------------r - 1 SYSTEM SENSOR P2RK ,wmws�ImwmTame uFS2-3o30-159 DO+159 MOD t SEE DEVICE DESIGNATION FOR STROBE cd SETTING (o Laro � � � .. 10'-0" NOTES: NOTIFICATION APPLIANCES: PENS FOR EACH CIRCUIT AND/OR CIRCUIT TYPE. AS BUILTS MUST INDICATE CHANGES TO I u "` ATC I I 1-OEWCE SUBSCRIPT: NW=NEW RR=REMOVE&RELOCATE EX=E%ISIWG TO REMAIN AC=ABOVE CEILING RB=RELAY BASE WP=WATERPROOF VlG=MRE GUARD ISD=ISO BASE 7 7 THE FINAL DEVICE INSTALLED LOCATIONS IF NOT INSTALLED AT LOCATION SHOWN ON ENDof LINE RESISTOR i ELEVATION DETAL CEILING INFO DESIGN DOCUMENTS. T-L -- 4------------------------ *------------� 2-CABIEING SHOWN IS FOR CIRCUIT REFERENCE ONLY AND DOES NOT INTENDED TO INDICATE 1HE EXACT PATHWAY '1 ? T ') 9 ',1 6.3. AS-BUILT REDDNES NOT PROVIDING THIS INFORMATION WILL BE RETURNED To THE 99 3-DEMCES SHOWN ON DRAWINGS IN GRAY SCALE ARE EXISTNG DEVICES AND MAY NOT BE INCLUDED IN THIS SYMBOL LEGEND UNLESS NOTED. INSTALLATION CONTRACTOR FOR CORRECTION. 4-SET Haiti/STROBE DEGBIE SETTING TO LOW FROM FACTORY SETTING OF HIGH,ONLESS OTHFRMSE NOTED ON THE DRAWINGS 7. AGREEMENT AND CONFIRMATION OF ALL MILESTONE EVENTS WILL BE MADE WITH PROJECT FLAG NOTE SHEET NOTE EQUIPMENT NOTE 311878E LF.SOUNI AMOFLY. BELL OMWATM MANAGER. - ---ZONROOM, BO NDRIES�-i 1 -----J 5-All DEVICES NTH A WP SUBSCRIPT MLL REWIRE THE USE OF A WIDWR OR wp BACKBOx 8. ALL FIELD SERVICES MUST BE SCHEDULED WITH PROJECT MANAGER WITH A MINIMUM OF 14 IB=18W 05=M°tl IM=10)W 135=1MW M=MNNaOT 8=8'BEIl M=MW 115-IISW 185-17W L80=180o1 H=H01#NERO 8=8'BDL WORKING DAYS ADVANCE NOTICE. -' -FULLNEIGIifWALL 80•75W HS=1Wal 1M•183W DT•177W F 111111-n 10=10BEI1 9. DO NOT INSTALL ONE VOLTAGE IN SAME CONDUIT AS POWER LIMITED CABLES. M=TBoI tM=tMW uB=1Mod 1E=LOWRFDUBTLY t2=1x IEu -----2HR RATED WALL PARTIALHIBGHTWALL NOTE A7PADJA DUMTFEDEYMRMTESTPATTIEDEVUENDWRRATED FIRE ALARM SPECIFIC NOTES: 1HRRATEDWALL NOTIFICATION I VISUAL CIRCUITS: 1. SMOKE DETECTORS SHALL NOT BE INSTALLED WITHIN 36"OF ANY AIR DIFFUSER. FLAGNOTES 2 2019 NFPA 72-17.7.1.12.3 REQUIRES THAT SMOKE DETECTORS SHALL NOT BE INSTALLED UNTIL NOTE i1 DESCRIPTION aRCuIiTYPE: RDaRTTwrFSMa AFTER FINAL CONSTRUCTION CLEAN-UP. C 'C'=FACP NAC CIRCUIT pgplg yp 2.1. ANY SMOKE DETECTORS THAT HAVE BEEN INSTALLED PRIOR To CLEW-UP MUST BE C 25 PROVIDE HINGED PLASTIC COVER FOR FIRE ALARM MANUAL PULL STATION(TYP.) N.=APSNACCIRCUIT CLEANED OR REPLACED AND WILL BE INVOICED ON A T&M BASIS. P=24VOC POWER CIRCUIT su34aRa#rxuMBER SITE MAP: Ir 24VDC RESET POWER CIRCUIT 3. WALL MOUNTED NOTIFICATION DEVICES BACKBOX BETWEEN A MINIMUM OF 80"ARE TO A MAXIMUM 9=STROBECIRCUIT OF 96"AFT. 4'=VOICORISER CIRCUIT O N1A0 CIRWIT# 3.1. DEVICES THAT ARE UNABLE TO BE MOUNTED WITHIN THAT RANGE MUST BE VERIFIED T=AU010 RISER CIRCUB WIRE SYMBOL D PRIOR TO PLANS FOR SYMBOL DESCRIPTION THHN FPL FPLP WET COLOR CODING CIRCUIT TYPE NOTES SYSTEMSE SERIES DEVICES AUDIO SELECTOR WTEESEI"OR1S 3.2. SEE FLOOR PLATS FOR CANDELA RATING OF EACH DEVICEIGHT INSTALLED. 'L'BERIEB OEACES EXCEEO9tSEPoE,4OE171E3 4. ALL MANUAL PULL STATIONS ARE TO BE MOUNTED AT A HEIGHT NO GREATER THAN 48'TO TOP = A 1 PAIR 16AWG FIRE RATED CABLE YES 971 60991E AQ225 CONVENTIONAL(IDC)CIRCUIT I,IJ-IrRn AND NO LOWER THAN 36'TO B070M(PER ADA REQUIREMENTS). - rwow.3 C 1 PAIR 14AWG FIRE RATED CABLE YES 972 60993B AQ226 AUDIBLE(NAC)CIRCUIT f -- 5. FIELD VERIFY ALL SPRINKLER MONITORING DEVICES WITH FIRE PROTECTION CONTRACTOR _ 6. FIELD VERIFY ALL WAG,FAN CONTROL FIRE/SMOKE DAMPERS AND DUCT DETECTORS LOCATIONS D 1 PAIR 16AWG FIRE RATED CABLE --- 971 60991B A0225 DATA(SLC)CIRCUIT /� 1 = ❑ NOTES: "Mr WITH MECHANICAL CONTRACTOR - E 'w DIFFERENT COLORS STRIPE COMBINATIONS TO BE USED FOR DIFFERENT CIRCUIT TYPES.LABEL ALL CIRCUITS ACCORDINGLY e �»' �mi HOH- a quo w' 8 8 8 7. FACP SHALL NOT BE ENERGIZED WITHOUT THE PRESENCE OF TECHNICIANS. / woro mi„- .n.-core wErtmnar Orr mo aw ee nrm wdusno a nr uu sraueR 8. NO TAPPING OF SIGNALING OR INITIATING ZONE CIRCUITS ARE ALLOWED. T-TAPPING OF STYLE 4CD 1-WIRE MANUFACTURER IS FOR REFERENCE PURPOSE ONLY. WHEN USING OTHER MANUFACTURE,ENSURE PROPER CROSS REFERENCE ADDRESSABLE CIRCUITS IS ALLOWED PROVIDING A SPLICE IS PROFESSIONALLY INSTALLED, 2-FPLP CAN BE USED IN MOST ALL APPLICATIONS WITH THE EXCLUSION OF WET AND CIRCUIT INTEGRITY REQUIREMENTS POLARITY IS OBSERVED AND SHIELDS ARE CONTINUOUS AND FREE of GROUNDS. SHIELDS MUST 3-INSTALL WIRING PER NEC. USE CABLE TYPE CONSISTENT WITH NEC REQUIREMENTS,IE PLENUM,RISER,UNDERGROUND,ETC. BE TERMINATED FRCP ONLY. MAIN BLDG FACP 8.1. CABLE SHIELDS SHALL BE SPLICED TOGETHER AT EVERY JUNCTION BETWEEN THE FACP SCOPE OF WORK&DESIGN BASIS 4-THE"Y"FIBER OPTIC CABLE LISTED IS A BELDEN CABLE PART NUMBER AS WEST PENN NO LONGER SUPPORTS FIBER OPTIC CABLE AND THE UST DEVICE ON EACH CABLE RUN. SHIELDS AND OTHER FIRE ALARM EB v� 5-THIS CABLE MUST BE INSTALLED IN A CONTINUOUS PATH POINT-TO-POINT. ABSOLUTLEY NO SPLICES ARE ALLOWED. CONDUCTORS(EXCEPT POWER GROUNDS)SHALL BE INSULATED AND COMPLETELY FREE FROM CONDUIT OR EARTH GROUNDS. SHIELDS WILL BE TIES To GROUND ONLY AT THE 6-THIS IS A SPECIFIC CABLE,NO ALTERNATES ARE ALLOWED FIRE ALARM SYSTEM FOR NEWLY ADDED PORTABLE BUILDINGS.NEW NOTIFICATION,INITIATION AND DETECTION FACP BY THE FIELD TECHNICIAN. P1 DEVICES TO BE INSTALLED.NOTIFICATION WILL BE POWERED BY FACP IN ADJACENT PORTABLE EXISTING 9. THE SYSTEM SHALL BE MONITORED BY A U.L.LISTED MONITORING STATION BEFORE AHJ TEST. PoRTABL FACP SEQUENCE OF OPERATIONS TO REMAIN IN PLACE AND UNCHANGED.AREAS OF WORK SHOWN IN THESE 10, AS-BUILTS ARE REQUIRED AT TIME OF AHJ ACCEPTANCE.REQUIRED ELECTRICAL RED LINES 9 D DRAWINGS ARE ONLY AREAS WITHIN SCOPE.NEW FACP To BE MONITORED BY MAIN FACP IN MAIN BUILDING. WITHIN 2 WEEKS PRIOR TO AHJ TESTS. D NAC Circuit Load, Voltage Drop FC Battery Load Calculations FACP 10.1. EACH CIRCUIT(SLC,NAC OR POWER)TO BE CLEARLY IDENTIFIED WITH A DISTINCT COLOR AREA OF WORK APS Name: FACP P1 P2 10.2. EACH NAC CIRCUIT MUST BE CLEARLY MARKED AS To WHICH DEVICES ARE ON EACH CIRCUIT AND IN THE ORDER THE DEVICES ARE WIRED To COMPLETE THE CIRCUIT, Location: PORTABLE Pi Standby Alarm: Output P Output 12 Output 93 Output I4 Output#5 Output 16 Output I7 Aue PS Type: NFW-50X(FACP) 0.1410 0.2570 VIsual VIsaal Not Used Nat Used Not Used Not Used Nol Used Power Part k Desaiptom N1 N2 %-X X-X %-X %-X X-X X-X Total Oly SWL IS Wdl Strobe set at 15cd BODOO 0.0430 2 2 4 FAIL(185) Wall Horn w/Strobe set at 185cd GODOO 0.2450 2 2 4 P WK 75 Wall Horn w Strobe set at 75cd,NO BOD00 0.1760 1 1 2 9 Devices per Circuit: 5 5 0 0 0 0 0 0 10 Total Standby Cirmit Calculated Amps(3): DODO 0.000 O.DDO GOD) 0.000 0.000 O.ODDD 0.0000 0.1410 Total Alarm Circuit Calculated Amps(1): 0.752 0.752 DDOO BODO 0,000 0.000 DODO 0.0000 0.2570 TO NCH Wire Gauge Used(awg): 14AWG 14AWG 14AWG 14AWG 14AWG 14AWG 14AWG 14AWG Total ED PORTABLE LO CEmil Length(fit): 85 115 D 0 0 0 0 0 Amps D 017 01]O 016 D r Estimated Voltage Drop(dc): 0.33 O45 0.00 0.00 JOB 0.00 0.00 JOB Required I� Estimated BOLE Vdtage(dc): 23.67 1 23.55 24.00 24.00 1 24.00 2400 2400 24.00 1.504 tAC N2-4 C N2-5 A CD I g Calculated Voltage Drop k 1.49 1.9% 0.0% OOR O.0% O.OR O.0% 0.09 018 15 15 015 IM C P 1)Curtest Draw Measurement based m:UL1971,16-33V,DC,High db&Temporal Patter D D A 2)Some Outdoor/WP Devices have the same Measured Current Draw as the Indoor Devices and may not listed separately above. 014C,D3)When the APS is configured fa°Doors',Output I4 shutedown on loss of AC Power. Therefore no'Standhy Current Draw is sham _ _ _ AF D E BATTERY LOAD CALC for FACP: NAC P.S.Mae Rating 2500 Total Amps Required: L504 W Used: 607 C ° 26 2A A czo Hours Standby 24 Total Standby Current 0.1410 Total Hours Required for Standby(AH): 3.4 AC c Minutes Alarm: 5 Total Alarm Current 1.7610 Total Hours Required fa Alarm(AH): 0.1 F 020 H Oil F Backup Generator? Unknown Minimum Battery Ske Neetletl(AH): 35 N2- N2-1 P5 Voice Evacuation? Na Spare Circuit Capacity 20X Spare Bottay Capacity Required: p.7 25 ZC 8 e C,D Military' No Spare Bottay Laad Factor. 20% Actual Battery Sze Required(AH): 42 - 01 F F 12 75 W MAXIMUM CHARGER CAPACITY I6: 'BAH T°`°'AN Rated Batteries Supplied: PORTABLE P2 FIRE ALARM LAYOUT L SCALE:1/8"=1'-0" ev °ATE. DESCRIPTION: DRAWN BY:APPR°VBY: CLIENT: N.I.C.E.T. CERTIFICATION "Gn C,F ioi25/2023 EAGLE CREEK ES PORTABLE 0, 0223 SUanITTALDRAwI"era S SF �\ RED HAWK oA Iv021oziz0z3 SawnaTAL DRAwINas(CHANGED ADDRESSES) SLIPUE MS STATEMENT sEaSDF all/02/2023 ARLINGTON SCHOOL DISTRICT F � w aen 1216 E 5TH STREET F THESE FIRE ALARM RAVINGS HAVE FIRE i'ROTECTION ARLINGTON,WA 98223 BEEN REVIEWED BY: NICE 8EpE811N CT a NGGR DATE, FIRE ALARM SYSTEM FIRE PROTECTION ENGINEERING 1m_ r . EA.E- EET TECHNOLOGY $4•'�LLE'i -0 eT ov ee rw Ir. e. - FlEE. _ e FIRE ALARM SYSTEMS-LEVEL IN 16 8 6 4 2 0 FA-1.01 NICIT CERTIFICATION�101668 ^ n n TENT. E. CERTIFICATION EXPIRES-111101024 PROJECT#: 1 2 3 4 5 6 7 8 9 RED HAWK 917 134th St.SW,Suite B-3,Everett,WA 98204 7) 5� FIRE PROTECTION Project Manager:James Pan Cell Phone:253-330-0736 Ever vLgUawt' Date: 11/3/2023 Fire Alarm System Product Submittals Project: Eagle Creek Elementary School Portable P1 &P2 Customer: Scott's Electric Site Address: 1216 E. 5th St. Pages: 32 Arlington, WA 98223 Material List of Data Sheets Item Manufacturer Model# Description 1 Notifier NFW-50X Addressable fire alarm control panel 2 Notifier FSP-951/B300-6 Addressable photo smoke detector and base 3 Notifier NBG-12LX/STI-1130 Addressable pull station w/protective cover 4 Notifier FMM-1 Addressable monitor module 5 Notifier 5602 Hard-wired heat detector 6 Spaceage E120V-GT 120v voltage protector 7 Ditek DTK-2MHLP24FWB 24vdc surge suppressor 8 System Sensor P2WL Wall horn strobe,white 9 System Sensor SWL Wall strobe,white 10 System Sensor P2RK Outdoor wall horn strobe,red (END) This page intentionally left blank �J NOT 1 F 1 E R° by Honeywell �► NFW-50X Intelligent Addressable FACP with Communicator General The FireWarden-50X (NFW-50X) is the latest intelligent address- able fire alarm control panel (FACP) within the FireWarden Series and is a direct replacement for the FireWarden-50 (NFW-50). The NFW-50X comes with a pre-installed communicator and supports up to 50 addressable devices in any combination of detectors or mod- — — ules. With an extensive list of powerful features, the NFW-50X pro- grams just like FireWarden-100 products, yet fits into applications previously served only by conventional panels. J The pre-installed IPOTS-COM is a dual technology (POTS and IP) communicator.The POTS transmits system status(alarms,troubles, AC loss, etc.)to a Central Station via the public switched telephone network.The IP communicator's internet monitoring capability sends alarm signals over the Internet saving the monthly cost of two dedi- cated business telephone lines.Although not required, the second- ary telephone line may be retained providing backup communication over the public switched telephone line.Optional cellular reporting is available using the CELL-MOD or CELL-CAB-N. Remote and local programming of the control panel is possible using the FS-Tools Upload/Download utility. Programming databases can be uploaded/downloaded via the panel's USB port(and USB cable) One-person audible or silent walktest with walktest log&printout or via an ethernet connection using the IPOTS-COM communicator. System alarm verification selection per detector point The USB port also allows for the download or upload of the entire PAS (Positive Alarm Sequence) and Pre-signal per point (NFPA program, history file, walk-test data, current status and system volt- 72 compliant) ages by means of a USB flash drive. Up to 16 ANN-BUS annunciators-8 per each ANN-Bus The power supply and all electronics are contained on a circuit Remote Acknowledge, Alarm Silence, Reset and Drill via board supported on a new quick install chassis and housed in a addressable modules or remote annunciator metal cabinet. Available accessories include local and remote Upload/Download of program and data via USB with optional FS- upload/download software, remote annunciators, and reverse polar- Tools Programming Utility ity/city box transmitter(4XTM). SLC COMMUNICATION LOOP Features • Supports FlashScan®and CLIP protocols • Listed to UL Standard 864, 10th edition SLC operates up to 10,000 ft. (3,000 m) in FlashScan mode with • Pre-installed IPOTS-COM Ethernet IP and POTS(Plain Old Tele- twisted, unshielded wire phone Service)Central Station Communicator Single addressable SLC loop which meets NFPA Class B and • Optional CELL-MOD or CELL-CAB-N GSM Central Station Com- Class A requirements municator over AlarmNet® 50 addressable device capacity(any combination of addressable • Compatible with SWIFT®wireless devices detectors and modules) • Auto-programming (learn mode) reduces installation time. Compatible with NOTIFIER FireWarden&ONYX Series address- Reports two devices set to the same address able devices(refer to the FireWarden SLC Wiring Manual) • Two independently programmable, built-in Style Z (Class A) or NOTIFICATION APPLIANCE CIRCUITS(NACS) Style Y(Class B)NAC circuits • Selectable strobe synchronization for System Sensor, Wheelock, Two independently programmable output circuits. Circuits can be and Gentex devices configured for the following outputs: • Notification Appliance Circuit End of Line resistor matching —Style Y(Class B) • Four programmable function keys for ease of maintenance —Style Z(Class A) • Two programmable relays and one fixed trouble relay Silence Inhibit and Autosilence timer options • Built-in Programmer Continuous, March Time, Temporal, or California code for main • Integral 80-character LCD display with backlighting circuit board NACs with two-stage capability • Real-time clock/calendar with automatic daylight savings control Selectable strobe synchronization per NAC • History file with 1,000 event capacity 2.5 A special application,250mA regulated,total power for NACs • Addressable sounder base NOTE:Maximum or total 24VDC system power shared between all NAC circuits and the ANN-BUS is 2.7 A • Control module delay timer • Automatic detector sensitivity testing(NFPA 72 compliant) PROGRAMMING AND SOFTWARE • Automatic device type-code verification Autoprogramming(learn mode)reduces installation time • Point trouble identification Custom English labels (per point) may be manually entered or • Waterflow selection per module point selected from an internal library file • Alarm verification selection per detector point Two programmable Form-C relay outputs • Maintenance alert warns when smoke detector dust accumula- 50 software zones tion is excessive Continuous fire protection during online programming DN-60955:C•7/16/2018—Page 1 of 4 • Program Check automatically catches common errors not linked order R for red.) to any zone or input point N-ANN-1/0: LED Driver Module provides connections to a user sup- • OFFLINE PROGRAMMING: Create the entire program in your plied graphic annunciator. (See DN-7105.) office using FS-Tools,a Windows®-based software package,and N-ANN-LED: Annunciator Module provides three LEDs for each upload/download system programming locally. Offline program- zone: Alarm, Trouble, and Supervisory. Ships with red enclosure. ming requires an ethernet connection. FS-Tools is available on (See DN-60242.) www.notifier.com. N-ANN-REED: Provides alarm (red) indicators for up to 30 input User interface zones or addressable points. (See DN-60242.) LED INDICATORS N-ANN-RLY: Relay Module provides 10 programmable Form-C • Fire Alarm(red) CO Alarm (red) relays. Can be mounted inside the cabinet. (See DN-7107.) N-ANN-S/PG: Serial/Parallel Printer Gateway module provides a • AC Power(green) Supervisory(yellow) connection for a serial or parallel printer. (See DN-7103.) • Trouble(yellow) Ground fault(yellow) ADDRESSABLE DEVICES • Battery fault(yellow) Disabled (yellow) FSP-951: Addressable low-profile photoelectric smoke detector. • Maintenance(yellow) Communication(yellow) FlashScan only. • Alarm Silenced (yellow) F1-F4 Programmable Function FSP-951-IV: Addressable low-profile photoelectric smoke detector. Keys(yellow) Ivory. FlashScan and CLIP mode. KEYPAD NP-200: Addressable low-profile photoelectric smoke detector. • 16 key alpha-numeric pad Acknowledge B300-6 base included, FlashScan only. NP-200-IV: Addressable low-profile photoelectric smoke detector. • Alarm Silence Drill (Manual Evacuate) Ivory, B300-6-IV base included. FlashScan and CLIP mode. • Four(4)programmable function keys • Reset(lamp test) FSP-951T: Addressable low-profile photoelectric smoke detector Product Line Information with thermal sensor. FlashScan only. FSP-951T-IV:Addressable low-profile photoelectric smoke detector NFW-50X: Addressable Fire Alarm Control Panel with one SLC with thermal sensor. Ivory. FlashScan and CLIP mode. loop. Includes main circuit board with display, pre-installed IPOTS- NP-20OT:Addressable low-profile photoelectric smoke detector with COM communicator, chassis with transformer, backbox with door, thermal sensor. B300-6 base included. FlashScan only. plastic bag containing screws, cables, key, etc. FS-Tools: Programming software for Windows®-based PC com- NP-200rmal Addressable low-profile photoelectric smoke detector puter.Available for download at www.notifier.com. with thermal sensor. Ivory, 6300 6 IV base included. FlashScan and CLIP mode. CELL-CAB-N/CELL-MOD: Optional GSM communicators. IPOTS-COM: Dual technology (POTS and IP) communicator. FS Remote test capable addressable photoelectric smoke (replacement board) deteectorctor f:for use with DNR(W) duct detector housing. FlashScan only. DP-ES-R: Optional dress panel for the NFW-50XR(red). DP-ES-B: Optional dress panel for NFW-50X(black). FSP-951 R-IV: Remote test capable addressable photoelectric smoke detector for use with DNR(W) duct detector housing. Ivory. TR-CE-B: Optional trim ring for semi-flush mounting. (Black. For FlashScan and CLIP mode. red, order TR-CE.) NP-20OR: Remote test capable addressable photoelectric smoke BB-XP: Optional cabinet for one or two modules. detector for use with DNR(W) duct detector housing. FlashScan BB-25: Optional cabinet for up to six modules mounted on CHS-6 only. chassis. NP-20OR-IV: Remote test capable addressable photoelectric smoke BB-26: Battery backbox, holds up to two 25 AH batteries&CHG-75. detector for use with DNR(W) duct detector housing. Ivory, FlashS- NFS-LBB: Battery box, houses two 55 AH batteries can and CLIP mode. CHS-6:Chassis,mounts up to six multi-modules in a BB-25 cabinet. FST-951: Low-profile 135°F fixed thermal sensor. FlashScan only. CHG-75: Battery charger for lead-acid batteries with a rating of 25 to FST-951-IV: Low-profile 135°F fixed thermal sensor. Ivory. FlashS- 75 AH. can and CLIP mode. CHG-120: Remote battery charging system for lead-acid batteries NH-200: Low-profile 135°F fixed thermal sensor. B300-6 base with a rating of 55 to 120 AH. Requires additional NFS-LBB for included, FlashScan only. mounting. NOTE:CHG 120 or CHG 75 required for batteries larger than 18AH. NH-200-IV: Low-profile 135°F fixed thermal sensor. Ivory. B300-6-IV base included, FlashScan and CLIP mode. BAT Series: Batteries,see data sheet DN-6933. FST-951 R: Low-profile, intelligent, rate-of-rise thermal sensor. PRN Series: UL listed compatible event printer. Uses tractor-fed FlashScan only. paper. FST-951 R-IV: Low-profile, intelligent, rate-of-rise thermal sensor. OPTIONAL MODULES Ivory. FlashScan and CLIP mode. 4XTM Reverse Polarity Transmitter Module: Provides a super- NH-20OR: Low-profile 135°F fixed thermal sensor. B300-6 base vised output for local energy municipal box transmitter, alarm and included, FlashScan only. trouble. Includes a disable switch and disable trouble LED. NH-20OR-IV: Low-profile 135°F fixed thermal sensor. Ivory. B300-6- COMPATIBLE ANNUNCIATORS IV base included, FlashScan and CLIP mode. N-ANN-80: Remote, black LCD annunciator mimics the information FST-951H: Low-profile intelligent 190°F/88°C fixed thermal sensor. displayed on the FACP LCD display. Recommended wire type is un- FlashScan only. shielded. FST-951 H-IV: Low-profile intelligent 190°F/88°C fixed thermal sen- N-ANN-100: Remote LCD annunciator mimics the information dis- sor. Ivory. FlashScan and CLIP mode. played on the FACP LCD display. Recommended wire type is un- NH-20OH: Low-profile intelligent 190°F/88°C fixed thermal sensor. shielded. For use in FM applications only. (Basic model is black; B300-6 base included, FlashScan only. Page 2 of 4—DN-60955:C•7/16/2018 NH-20OH-IV: Low-profile intelligent 190°F/88°C fixed thermal sen- zone of supervised polarized Notification Appliances. Mounts sor. Ivory. B300-6-IV base included, FlashScan and CLIP mode. directly to a 4.0" (10.16 cm.) electrical box. NAC option requires Legacy Devices external 24 VDC to power notification appliances. FSP-851:Addressable low-profile photoelectric smoke detector. FRM-1: Addressable relay module containing two isolated sets of NP-100:Addressable low-profile photoelectric smoke detector. Form-C contacts, which operate as a DPDT switch. Mounts directly to a 4.0"(10.16 cm.)box,surface mount using the SMB500. FSP-851T: Addressable low-profile photoelectric smoke detector NC-10OR: Addressable relay module containing two isolated sets of with thermal sensor. Form-C contacts, which operate as a DPDT switch. Mounts directly NP-10OT:Addressable low-profile photoelectric smoke detector with to a 4.0"(10.16 cm.)box,surface mount using the SMB500. thermal sensor. NBG-12LX: Addressable manual pull station with interface module FSP-851 R: Remote test capable addressable photoelectric smoke mounted inside. detector for use with DNR(W)duct detector housing. NOT-BG12LX: Addressable manual pull station with interface mod- NP-100R: Remote test capable addressable photoelectric smoke ule mounted inside. detector for use with DNR(W)duct detector housing. ISO-X: Fault Isolator Module. FST-851: Fast-response, low-profile heat detector. N100-ISO: Fault Isolator Module. NH-100: Fast-response, low-profile heat detector. ISO-6: Six-fault isolator module. Mount one or two modules in a BB- FST-851 R: Fast-response, low-profile heat detector with rate-of-rise XP cabinet(optional). Mount up to six modules on a CHS-6 chassis option. in a CAB-3/CAB-4 series cabinet. NH-10OR: Fast-response, low-profile heat detector with rate-of-rise SMB500: Used to mount all modules except FMM-101/NMM-100P. option. NMM-100-10: Ten-input monitor module. Mount one or two modules FST-851 H: Fast-response, low-profile heat detector that activates at in a BB-2F cabinet (optional). Mount up to six modules on a CHS-6 190°F/88°C. chassis in a BB-6F cabinet. NH-100H: Fast-response, low-profile heat detector that activates at NZM-100-6: Six-zone interface module. Mount one or two modules 190°F/88°C. in a BB-XP cabinet(optional). Mount up to six modules on a CHS-6 FAPT-851:Addressable low-profile multi-sensor detector. chassis in a CAB-3/CAB-4 series cabinet. NP-A100:Addressable low-profile multi-sensor detector. SW/FT Wireless Devices B20OS: Programmable, addressable sounder base. FWSG:Wireless Gateway B200SR:Addressable sounder base. FWD-20OP: intelligent,wireless photo detector. DNR: InnovairFlex low-flow non-relay duct-detector housing. (Order FWH-200ROR135: LiteSpeed intelligent wireless rate of rise (135°) FSP-851 R, FSP-951 R,or NP-100R separately.) heat detector. DNRW: InnovairFlex low-flow non-relay duct-detector housing, with FWD-200ACCLI MATE:Wireless Acclimate Detector NEMA-4 rating. Watertight. (Order FSP-851R, FSP-951R, or FWH-200FIX135: intelligent wireless fixed-temperature (135°) heat NP-10OR separately.) detector. Addressable Modules FW-MM: Intelligent wireless monitor module. FMM-1: Addressable Monitor Module for one zone of normally-open FW-RM: Intelligent wireless relay module. dry-contact initiating devices. Mounts in standard 4.0" (10.16 cm.) NBG-12LW: Intelligent wireless pull station. box. Includes plastic cover plate and end-of-line resistor. Module WAV-RL,WAV-WL,WAV-CRL,WAV-CWL: Intelligent AV bases. may be configured for either a Style B (Class B)or Style D (Class A) W-USB: Wireless USB radio/antenna dongle that plugs into the IDC. USB port of a PC running SWIFT Tools. NMM-100: Addressable Monitor Module for one zone of normally- SWIFT Tools: Programming and diagnostic utility for the Wireless open dry-contact initiating devices. Mounts in standard 4.0" (10.16 Gateway and devices.Available for download from firelite.com. cm.) box. Includes plastic cover plate and end-of-line resistor. Mod- NOTE: For more information on Compatible Addressable Devices for ule may be configured for either a Style B(Class B)or Style D(Class use with the FireWarden-50X, see the following data sheets (document A)IDC. numbers): NP-200 Series (DN-60979), NH-200 Series (DN-60980), FDM-1: Dual Monitor Module.Same as NMM-100 except it provides FSP-851 Series (DN-6935), FSP-951 Series (DN-60977), FST-851 two Style B(Class B)only IDCs. Series (DN-6936), FST-951 Series (DN-60975), FAPT-851 (DN-6937), NDM-100: Dual Monitor Module. Same as NMM-100 except it pro- N1004SO (DN-6994), NP-100 series (DN-6995), NH-100/NH-100R vides two Style B(Class B)only IDCs. (DN-6997), DNR/InnovairFlex (DN-60424, DN-60429), NP-A100 FMM-101: Miniature version of NMM-100. Excludes LED and Style (DN-6998), NMM-100/NMM-100P/NDM-100/NZM-100 (DN-6999), NC-100 (DN-7000), NC-10OR (DN-60383), NMM-100-10 (DN-6990), D option.Connects with wire pigtails. May mount in device backbox. MM-1/FDM-1/FZM-1/FMM-101 (DN-6720), FCM-1/FRM-1 (DN-6724), NMM-10OP: Miniature version of NMM-100. Excludes LED and Style NOT-BG12LX (DN-7001), NBG-12LX (DN-6726), and FireWarden D option.Connects with wire pigtails. May mount in device backbox. SLC Manual (52304). FZM-1: Similar to NMM-100. Addressable Monitor Module for one ADDRESSABLE DEVICE ACCESSORIES zone of conventional two-wire detectors. Requires resettable 24 End-of-Line Resistor Assembly (R-47K and R-3.9K): The VDC power. Refer to the Device Compatibility Document for listed 47k ohm assembly supervises the FMM-1/NMM-100-10, FDM-1/ compatible devices and quantity limitation. NDM-100, FMM-101/NMM-100P, and FCM-1/NC-100 module cir- NZM-100: Similar to NMM-100.Addressable Monitor Module for one cuits. The 3.9k ohm assembly supervises the XP6-MA/NZM-100-6 zone of conventional two-wire detectors. Requires resettable 24 module circuit.These resistors are included with each module. VDC power. Refer to the Device Compatibility Document for listed Power Supervision Relay: Supervises the power to 4-wire smoke compatible devices and quantity limitation. detectors and notification appliances. FCM-1: Addressable Control Module for one Style Y/Z (Class B/A) zone of supervised polarized Notification Appliances. Mounts Wiring Requirements directly to a 4.0" (10.16 cm.) electrical box. NAC option requires external 24 VDC to power notification appliances. While shielded wire is not required, it is recommended that all SLC NC-100: Addressable Control Module for one Style Y/Z(Class B/A) wiring be twisted-pair to minimize the effects of electrical interfer- ence. Refer to the panel manual for wiring details. DN-60955:C•7/16/2018—Page 3 of 4 SPECIFICATIONS System Capacity Temperature and Humidity Ranges • Intelligent Signaling Line Circuits................................................I This system meets NFPA requirements for operation at 0—49°C/32 • Addressable device capacity....................................................50 —120°F and at a relative humidity 93%±2%RH(noncondensing)at 32°C ± 2°C (90oF ± 3°F). However, the useful life of the system's • Programmable software zones.................................................50 standby batteries and the electronic components may be adversely • Annunciators.............................................................................16 affected by extreme temperature ranges and humidity. Therefore, it is recommended that this system and its peripherals be installed in Electrical Specifications an environment with a normal room temperature of 15—27°C/60— AC Power: Operates in either 120 or 240 VAC, 50/60 Hz, 3.25 A, 80°F. auto-sensing- no switch required. Wire size: minimum 14 AWG NFPA Standards (2.00 mri with 600 V insulation. Nonpower-limited, supervised. Battery: Two 12 V 18 AH lead-acid batteries. Battery Charger The FireWarden-50X complies with the following NFPA 72 Fire Capacity: 7-18 AH (FireWarden-50X cabinet holds maximum of two Alarm Systems requirements: 18 AH batteries.) —LOCAL (Automatic, Manual, Waterflow and Sprinkler Supervi- Communication Loop: Supervised and power-limited. sory). Notification Appliance Circuits: Terminal Block provides connec- —AUXILIARY (Automatic, Manual and Waterflow) (requires tions for two NACs, Style Y (Class B) or Style Z (Class A). Special 4XTM). Application power. Power-limited, supervised circuitry. Maximum —REMOTE STATION (Automatic, Manual and Waterflow) signaling current per circuit: 2.5 amps special application, 250mA (Where a DACT is not accepted,the alarm,trouble and supervi- regulated. End-of-Line Resistor: 4.7k ohm, '/2 watt (P/N 71252 UL sory relays may be connected to UL 864 listed transmitters. For listed)for Style Y(Class B) NAC; system capable of 1.9 kQ-22 kQ reverse polarity signaling of alarm and trouble, 4XTM is ELR range. Refer to the NOTIFIER Device Compatibility Document required.) for listed compatible devices. —PROPRIETARY(Automatic, Manual and Waterflow). Two Programmable Relays and One Fixed Trouble Relay: Con- —CENTRAL STATION (Automatic, Manual and Waterflow, and tact rating: 2.0 A @ 30 VDC (resistive), 0.5 A @ 30 VAC (resistive). Sprinkler Supervised). Form-C relays, non-power-limited, non-supervised. —OT, PSDN (Other Technologies, Packet-switched Data Net- work) Cabinet Specifications —IBC 2012,IBC 2009, IBC 2006,IBC 2003, IBC 2000(Seismic). Door: 19.26" (48.92 cm.) high x 16.82" (42.73 cm.) wide x —CBC 2007(Seismic) 0.72" (1.82 cm.) deep. Backbox: 19.00" (48.26 cm.) high x 16.65" (42.29 cm.) wide x 5.25" (13.34 cm.) deep. Trim Ring (TR- Agency Listings and Approvals CE/B): 22.00"(55.88 cm.)high x 19.65"(49.91 cm.)wide. The listings and ap provals pprovals below apply to the basic FireWarden-50X control panel. In some cases, certain modules may not be listed by Shipping Specifications certain approval agencies,or listing may be in process. Consult fac- Weight: 26.9 lbs. (12.20 kg.) Dimensions: 20.00" (50.80 cm.) high tory for latest listing status. x 22.5"(57.15 cm.)wide x 8.5"(21.59 cm.)deep. UL: S635 • CSFM: 7165-0028:0505 • FDNY: COA#6268 I® ENGINEERING B MANUFACTURING QUALITY SYSTEMS This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. NOTIFIER AlarmNet@,NOTIFIER@,FireWarden@,SWIFT@,and System Sensor@ are registered trademarks of Honeywell International Inc.Microsoft and 12 Clintonville Road Windows@ are registered trademarks of the Microsoft Corporation. 0Northford,CT 06472 ©2018 by Honeywell International Inc.All rights reserved.Unauthorized NOTIFIER 203.484.7161 use of this document is strictly prohibited. www.notifier.com Country of Origin:USA by Honeywell �J NOT 1 F 1 E R° by Honeywell FSP-951 Series Addressable Photoelectric Smoke Detectors The NOTIFIERO FSP-951 Series intelligent plug-in smoke detectors are designed for both performance and aesthetics, and are direct replacements for the FSP-851 Series. A new modern, sleek, con- temporary design and enhanced optical sensing chamber is engi- neered to sense smoke produced by a wide range of combustion sources in accordance with more stringent code standards. The FSP-951 Series detector sensitivity can be programmed in the control panel software. Sensitivity is continuously monitored and reported to the panel. Point ID capability allows each detector's address to be set with rotary, decimal address switches, providing ( \ exact detector location for selective maintenance when chamber I contamination reaches an unacceptable level. Dual electronic thermistors add 135°F(57°C)fixed temperature thermal sensing on the FSP-951T. The FSP-951 R is a remote test capable detector for use with DNR Series duct detector housings. FSP-951 series detec- tors are available for both FlashScanO and CLIP applications as designated. Features SLC LOOP: Separate base allows interchange of photoelectric, ionization and • Two-wire SLC loop connection thermal sensors • Unit uses base for wiring OPTIONS: • Compatible with FlashScanO and CLIP protocol systems • Optional relay, isolator,and sounder bases • Stable communication technique with noise immunity Installation ADDRESSING: FSP-951 Series plug-in intelligent smoke detectors use a detach- • Addressable by device able base to simplify installation, service and maintenance. Installa- • Rotary,decimal addressing tion instructions are shipped with each detector. (Refer to the NOTIFIER panel manuals for device capacity.) Mount detector base(all base types)on an electrical backbox which ARCHITECTURE: is at least 1.5" (3.81 cm) deep. For a chart of compatible junction • Sleek, low-profile,stylish design boxes,see DN-60054, • Unique single-source design to respond quickly and dependably NOTE: Because of the inherent supervision provided by the SLC loop, to a broad range of fires end-of-line resistors are not required. Wiring "T-taps" or branches are permitted for Class"B"wiring only. • Integral communications and built-in device-type identification When using relay or sounder bases, consult the ISO-X(A) installation • Built-in tamper resistant feature sheet 156-1380 for device limitations between isolator modules and isola- • Remote test feature from the panel for bases. • Walk test with address display (an address on 121 will blink the Construction detector LED: 12-[pause]-1(FlashScan systems only) These detectors are constructed of fire-resistant plastic. The FSP- • Built-in functional test switch activated by external magnet 951 Series plug-in intelligent smoke detectors are designed to com- • Removable cover and insect-resistant screen for simple field mercial standards and offer an attractive appearance. cleaning • Expanded color options Operation OPERATION: Each FSP-951 Series detector uses one of the panel's addresses (total limit is panel dependent) on the NOTIFIER Signaling Line Cir- • Designed to meet UL 268 7th Edition cuit (SLC). It responds to regular polls from the control panel and • Factory preset at 1.5%nominal sensitivity for panel alarm thresh- reports its type and the status. If it receives a test command from the old level panel (or a local magnet test), it stimulates its electronics and • LED"blinks"when the unit is polled (communicating with the fire reports an alarm. It blinks its LEDs when polled and turns the LEDs panel)and latches in alarm. on when commanded by the panel.The FSP-951 Series offers fea- • Low standby current tures and performance that represent the latest in smoke detector technology. MECHANICALS: • Sealed against back pressure Product Line Information • SEMS screws for wiring of the separate base NOTE:"-IV"suffix indicates CLIP and FlashScan device. • Designed for direct-surface or electrical-box mounting FSP-951: hite, low-profile intelligent photoelectric sensor, FlashS- • Plugs into separate base for ease of installation and maintenance can only FSP-951A: Same as FSP-951 but with ULC listing DN-60977:D•8/13/2020—Page 1 of 3 FSP-951-IV: Ivory, low-profile intelligent photoelectric sensor B200SCOA-IV: Ivory Intelligent, programmable sounder base in FSP-951A-IV: Same as FSP-951-IV but with ULC listing English/French (required in Canada for ULC applications with CO Series detector applications, ULC listing FSP-951T: White, same as FSP-951 but includes a built-in 135°F B20OS-LF-WH: White, Low Frequency Intelligent, programmable (57°C)fixed-temperature thermal device, FlashScan only sounder base. Produces a fundamental frequency of 520 Hz +/- FSP-951TA: Same as FSP-951T but with ULC listing 10% with a square wave or its equivalent; designed to meet the FSP-951T-IV: Ivory,same as FSP-951T but includes abuilt-in 135°F NFPA 72 sleeping space requirement. (CSFM:7300-1653:0238) (57°C)fixed-temperature thermal device B20OS-LF-IV: Ivory, Low Frequency Intelligent, programmable sounder base. Produces a fundamental frequency of 520 Hz +/- FSP-951TA-IV: Same as FSP-951T-IV but with ULC listing 10% with a square wave or its equivalent; designed to meet the FSP-951 R: White, low-profile intelligent photoelectric sensor, NFPA 72 sleeping space requirement. (CSFM:7300-1653:0238) remote test capable,for use with DNR/DNRW, FlashScan only B200SR-WH: White, Intelligent sounder base capable of producing FSP-951 RA: Same as FSP-951 R but with ULC listing, for use with sound output with ANSI Temporal 3 or continuous tone. Intended for DNRA retrofit applications. (CSFM:7300-1653:0213) FSP-951 R-IV: Ivory, low-profile intelligent photoelectric sensor, B200SR-IV: Ivory, Intelligent sounder base capable of producing remote test capable,for use with DNR/DNRW sound output with ANSI Temporal 3 or continuous tone. Intended for retrofit applications. (CSFM:7300-1653:0213) FSP-951 RA-IV: Same as FSP-951 R-IV but with ULC listing,for use B200SRA-WH: Same as B200SR-WH with, ULC listing with DNRA INTELLIGENT BASES B200SRA-IV: Same as B200SR-IV in Ivory color, ULC listing B200SR-LF-WH: White, Low Frequency Intelligent, programmable \ NOTE: For details on intelligent bases,see DN-60961. sounder base. Produces a fundamental frequency of 520 Hz +/- y B300-6:White,6"base, standard flanged low-profile mounting base 10% with a square wave or its equivalent; designed to meet the 300-1653:0109) NFPA 72 sleeping space requirement. Intended for retrofit applica- B300-6-IV: Ivory,6" base, standard flanged low-profile mounting tions. (CSFM:7300-1653:0238) base(CSFM:7300-1653:0109) B200SR-LF-IV: Ivory, Low Frequency Intelligent, programmable B300A-6: Same as B300-6, ULC listed sounder base. Produces a fundamental frequency of 520 Hz +/- 10% with a square wave or its equivalent; designed to meet the B30OA-6-IV: Ivory, 6" standard flanged low-profile mounting base, NFPA 72 sleeping space requirement. Intended for retrofit applica- ULC listed tions. (CSFM:7300-1653:0238) B300-6-BP: Bulk pack of B300-6, package contains 10 MOUNTING KITS AND ACCESSORIES B501-WHITE: White, 4" standard European flangeless mounting TR300:White, replacement flange for B210LP(A)base base. UL/ULC listed(CSFM:7300-1653:0109) TR300-IV: Ivory, replacement flange for B210LP(A) base B501-BL: Black, 4" standard European flangeless mounting base. UL/ULC listed(CSFM:7300-1653:0109) RA100Z(A): Remote LED annunciator. 3-32 VDC. Mounts to a U.S. B501-IV: Ivory color, 4" standard European flangeless mounting single-gang electrical box. For use with B501(A)and B300-6(A). base. UL/ULC listed(CSFM:7300-1653:0109) M02-04-00:Test magnet B501-WHITE-BP: Bulk pack of B501-WHITE contains 10 M02-09-00:Test magnet with telescoping handle B224RB-WH:White, relay base(CSFM: 7300-1653:0216) CK300: Color Kit(includes cover and trim ring),white, 10-pack B224RB-IV: Ivory, relay base(CSFM:7300-1653:0216) CK300-IV:Color Kit(includes cover and trim ring), ivory, 10-pack B224RBA-WH:White, relay base, ULC listing CK300-BL: Color Kit(includes cover and trim ring),black, 10-pack B224RBA-IV: Ivory, relay base, ULC listing B224BI-WH:White, isolator detector base(CSFM:7300-1653:0216) B224BI-IV: Ivory isolator detector base(CSFM:7300-1653:0216) B224BIA-WH:White, isolator detector base, ULC listing B224BIA-IV: Ivory isolator detector base, ULC listing B20OS-WH:White, Intelligent addressable sounder base capable of producing sound output in high or low volume with ANSI Temporal 3, ANSI Temporal 4,continuous tone,marching tone,and custom tone. Uses FlashScan protocol. (CSFM:7300-1653:0213) B20OS-IV: Ivory, Intelligent addressable sounder base capable of producing sound output in high or low volume with ANSI Temporal 3, ANSI Temporal 4,continuous tone,marching tone,and custom tone. Uses FlashScan protocol. (CSFM:7300-1653:0213) B200SA-WH: Same as B200S-WH, ULC listing B200SA-IV: Same as B200S-IV, ULC listing B200SCOA-WH: White, Intelligent, programmable sounder base in English/French (required in Canada for ULC applications with CO Series detector applications Page 2 of 3—DN-60977:D•8/13/2020 SPECIFICATIONS Sensitivity: Listings and Approvals • UL Applications: 0.5%to 4.0%per foot obscuration. Listings and approvals below apply to the FSP-951 Series detectors. • ULC Applications:0.5%to 3.5%per foot obscuration In some cases, certain modules may not be listed by certain Size:2.0" (51 mm) high; base determines diameter approval agencies, or listing may be in process. Consult factory for —B300-6 series: 6.1" (15.6 cm)diameter latest listing status. —B501 series:4" (10.2 cm)diameter • UL/ULC Listing: S1115 For a complete list of detector bases see ON-60981 • FM Approved • CSFM:7272-0028:0503 Shipping weight:3.4 oz. (95 g) Operating temperature range: • FSP-951 Series: 32°F to 122°F(0°C to 50oC) • FSP-951 T Series:32°F to 100°F(0°C to 38°C) • FSP-951 R Series installed in DNR/DNRA/DNRW,-4°F to 158°F (-20°C to 70oC) UL/ULC Listed Velocity Range: 0-4000 ft/min. (1219.2 m/min.), suitable for installation in ducts Relative humidity: 10%—93%non-condensing Thermal ratings:fixed-temperature set point 135OF(57°C), rate-of- rise detection 15°F(8.3°C)per minute, high temperature heat 190°F (88°C) ELECTRICAL SPECIFICATIONS Voltage range: 15-32 volts DC peak Standby current(max.avg.): 200pA @ 24 VDC (one communica- tion every 5 seconds with LED enabled) Max current:4.5 mA @ 24 VDC("ON") DETECTOR SPACING AND APPLICATIONS NOTIFIER recommends spacing detectors in compliance with NFPA 72. In low airflow applications with smooth ceiling, space detectors 30 feet (9.1 m). For specific information regarding detector spacing, placement, and special applications refer to NFPA 72. A System Smoke Detector Application Guide, document SPAG91, is available at www.systemsensor.com. I® ENRINEERINR IIIMANUFACTURINL QUALITY SYSTEMS This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. NOTIFIER FlashScan®, NOTIFIER®,and System Sensor®are registered trade- 12 Clintonville Road marks of Honeywell International,Inc. Northford,CT 06472 @2020 by Honeywell International Inc.All rights reserved.Unauthorized NOT 1 F 1 E R 203.484.7161 use of this document is strictly prohibited. www.notifier.com Country of Origin:Mexico by Honeywell This page intentionally left blank DN-6726:D•H-240 NBG-12LX NOTI FI E R° Addressable Manual Pull Station by Honeywell Intelligent/Addressable Devices ,General The Notifier NBG-12LX is a state-of-the-art, dual-action (i.e., . requires two motions to activate the station) pull station that includes an addressable interface for any Notifier intelligent control panel except Fire Warden series panels, and the NSP- 25 panel. Because the NBG-12LX is addressable, the control panel can display the exact location of the activated manual station. This leads fire personnel quickly to the location of the alarm. Features • Maintenance personnel can open station for inspection and address setting without causing an alarm condition. • Built-in bicolor LED, which is visible through the handle of _ the station, flashes in normal operation and latches steady red when in alarm. • Handle latches in down position and the word"ACTIVATED" appears to clearly indicate the station has been operated. • Captive screw terminals wire-ready for easy connection to The NBG-12LX SLC loop(accepts up to 12 AWG/3.25 mm2 wire). • Can be surface mounted (with SB-10 or SB-1/0) or semi- Addressable Manual Pull Station flush mounted. Semi-flush mount to a standard single- gang,double-gang,or 4" (10.16 cm)square electrical box. Installation • Smooth dual-action design. The NBG-12LX will mount semi-flush into a single-gang, dou- • Meets ADAAG controls and operating mechanisms guide- ble-gang, or standard 4" (10.16 cm) square electrical outlet lines (Section 4.1.3[13]); meets ADA requirement for 5 lb. box, or will surface mount to the model SB-10 or SB-1/0 sur- maximum activation force. face backbox. If the NBG-12LX is being semi-flush mounted, • Highly visible. then the optional trim ring (BG12TR) may be used. The BG12TR is usually needed for semi-flush mounting with 4" • Attractive shape and textured finish. (10.16 cm)or double-gang boxes(not with single-gang boxes). • Key reset. • Includes Braille text on station handle. Operation • Optional trim ring(BG12TR). Pushing in,then pulling down on the handle causes it to latch • Meets UL 38, Standard for Manually Actuated Signaling in the down/activated position. Once latched, the word "ACTI- Boxes. VATED" (in bright yellow) appears at the top of the handle, • Up to 99 NBG-12LX stations per loop on CLIP protocol while a portion of the handle protrudes from the bottom of the loops. station.To reset the station, simply unlock the station with the e Up to 159 NBG-12LX stations per loop on FlashScan®pro- key and pull the door open.This action resets the handle;clos- tocolloops. ing the door automatically resets the switch. • Dual-color LED blinks green to indicate normal on Each manual station, on command from the control panel, FlashScan®systems. sends data to the panel representing the state of the manual switch.Two rotary decimal switches allow address settings Construction (1 —159 on FlashScan®systems, 1 —99 on CLIP systems). Shell, door, and handle are molded of durable polycarbonate Architectural/Engineering material with a textured finish. Specifications Specifications Manual Fire Alarm Stations shall be non-coded, with a key- operated reset lock in order that they may be tested, and so • Shipping Weight: 9.6 oz. (272.15 g) designed that after actual Emergency Operation, they cannot • Normal operating voltage:24 VDC. be restored to normal except by use of a key.An operated sta- • Maximum SLC loop voltage:28.0 VDC. tion shall automatically condition itself so as to be visually detected as activated. Manual stations shall be constructed of • Maximum SLC standby current: 375 NA. red-colored polycarbonate material with clearly visible operat- • Maximum SLC alarm current: 5 mA. ing instructions provided on the cover. The word FIRE shall • Temperature Range:32°F to 120°F(0°C to 49°C) appear on the front of the stations in white letters, 1.00 inches • Relative Humidity: 10%to 93%(noncondensing) (2.54 cm) or larger. Stations shall be suitable for surface mounting on matching backbox SB-10 or SB-1/0;or semi-flush • For use indoors in a dry location mounting on a standard single-gang, double-gang, or DN-67260•4/13/2012—Page 1 of 2 4" (10.16 cm) square electrical box, and shall be installed within the limits defined by the Americans with Disabilities Act (ADA) or per national/local requirements. Manual Stations shall be Underwriters Laboratories listed. Manual stations shall connect with two wires to one of the con- trol panel SLC loops. The manual station shall, on command from the control panel,send data to the panel representing the state of the manual switch. Manual stations shall provide address setting by use of rotary decimal switches. The loop poll LED shall be clearly visible through the front of the station. The LED shall flash while in the normal condition, and stay steadily illuminated when in alarm. Product Line Information NBG-12LX: Dual-action addressable pull station. Includes key oc Ing ea ure. (Listed for Canadian and non-Canadian appli- cations.) NBG-12LXSP: Spanish/English labelled version. NBG-12LXP: Portuguese labelled version. SB-10: Surface backbox; metal. SB-1/0: Surface backbox; plastic. BG12TR:Optional trim ring. 17021: Keys, set of two. NY-Plate: New York City trim plate. Agency Listings and Approvals In some cases, certain modules or applications may not be listed by certain approval agencies, or listing may be in pro- cess.Consult factory for latest listing status. • UL/ULC Listed: S692 (listed for Canadian and non-Cana- dian applications). • MEA:67-02-E. • CSFM: 7150-0028:0199. • FDNY: COA#6085(NFS2-640), COA#6098(NFS2-3030). • BSMI:CI313066760047. • U.S.Coast Guard. • Lloyd's Register. • FM Approved. Patented: U.S. Patent No. D428,351; 6,380,846; 6,314,772; 6,632,108. NOTIFIERO and FlashScanO are registered trademarks of Honeywell International Inc. 02012 by Honeywell International Inc.All rights reserved.Unauthorized use of this document is strictly prohibited. I�O 9001 This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. ENGINEERING&MANUFACTURING All specifications are subject to change without notice. QUALITY SYSTEMS Made in the U.S.A. For more information,contact Notifier.Phone:(203)484-7161,FAX:(203)484-7118. www.notifier.com Page 2 of 2—DN-67260•4/13/2012 PRODUCTS STI STOPPER 11 "D KEY FEATURES General Information Proven effective for more than 40 years in helping stop false fire alarms without restricting legitimate alarms. ►�+ Can be used as a guard against physical damage to a manual pull station,with or without the optional warning horn. Three year guarantee against breakage of polycarbonate in • normal use(one year on electro :Y mechanical and electronic C Rus components). ADA Design Compliant • BSA Larger sizes and surface mounted pull stations accommodated with �,�.. STI-3100 conduit spacer. LIFT HERE Weather models have closed cell ,,� gaskets. ® The Stopper II design is a registered trademark of Safety Technology sTi-ttoo International,Inc. Construction UL Listed to U.S.and Canadian PRODUCT OVERVIEW safety standards(also for custom This protective cover has been helping to stop false fire alarms around the world for labeling). more than 40 years, without restricting legitimate alarms. All models offer excellent Installation When covering a pull station protection against physical damage(both accidental and intentional) and several outside,UL requires stations to be against severe environments both inside and out. It is ideal for schools, colleges, listed for outdoor use. hospitals, nursing homes, stores, hotels and public buildings of almost every kind Typical working properties of where there is a threat of false alarms. polycarbonate are ao°to 250°F HOW IT WORKS Electronics Power source is a 9V DC alkaline Stopper II consists of a clear, tamperproof, tough polycarbonate shield and frame, but battery included on standard the line includes models with the option of a piezo horn, spacer and gaskets. The cover Stopper II(remote powered unit accommodates most manual pull stations. When the Stopper II with horn is lifted to available).options gain access to the protected alarm, a piercing self-contained 95 or 105 dB warning optional horn has a choice of 95 or horn (at one foot)sounds. Immediate attention is drawn to the area and a prankster 105 dB at one foot. will either run or be caught. The cover is connected to the frame by a cable. When the Standard red units have"In Case cover is lifted, it drops off of the frame and a horn will sound (models with horn) until of Fire..."label unless specified with "NR"(no label)or"CR"(custom the cover is snapped back onto the frame or for the life of the battery. label). For more information, call 248-673-9898 or visit www.sti-usa.com. Q. Safety Technology International STI Stopper III Dimensions and Technical Information MODELS AVAILABLE APPROVALS & WARRANTY Stopper II°Models Indoor Use TESTING STI-1100** With horn for flush mount It has been tested and approved or listed by: STI�-1130 With horn and spacer UL/cUL Listed No.S2466 0f1=TZIID",t Without horn flush mount For fire alarm applications,UL38 requires outdoor listed stations for STI-1230** Without horn with spacer outdoor use Weather Stopper®with gaskets(Indoor/Outdoor rated) State of California(obtain local fire marshal approval) STI-1150* With horn flush mount and gaskets MEA 49-00-E(STI-1200) STI-1155* With horn surface mount and gaskets Flush models ADA Compliant.Surface models ADA Compliant for STI-1250* Without horn flush mount and gaskets operation(UL Certified No.S2466) STI-3150** Without horn surface mount and gaskets Weather Stopper versions designed to meet the requirements of IP54. Accessories The indoor/outdoor rated station covers,when mounted on a KIT-316 Louvers for STI-3100 smooth surface,provide a rain tight seal similar to a 3R enclosure KIT-1-119015 Two 3/32"Allen wrenches rating. KIT-MO2002 Clear Frame for Stopper II Series WARRANTY STI-1102 Replacement horn for cover with alarm Three year guarantee against breakage of polycarbonate in normal STI-1280 Backplate use(one year on electro mechanical and electronic components). STI-3002 Weather gasket STI-3003 Conduit gasket STI-3004 Rigid conduit gasket IMPORTANT NOTICE STI-3100 2"conduit spacer with a frame,1/2'or 3/4"conduit entry Stopper II"FIRE"models are intended to be used in areas where STI-3104 2"conduit spacer with 1/2"or 3/4"conduit entry the incidence of false fire alarms from manual pull stations is high or (includes one 3/4"conduit entry gasket) has proven to be a serious problem.Any disadvantage of this device * Add-NR for no label on horn housing is more than balanced when one considers the consequences of Add-CR for custom label on horn housing false fire alarms,especially if fire service personnel and equipment Add-FR for French labeling are responding to a false fire alarm when they are needed for a real Add-ES for Spanish labeling fire somewhere else.Add to this the disruption to the facility when *Available in a 6-pack(STI-1100&STI-1130 also in a 12-pack) false alarms occur. If you have,or may have,a problem with false fire alarms or physical/weather damage to your fire alarm activation devices,the Stopper II could prove invaluable. COVER *WARNINGAFor RC models: UL Listing does not permit relay 5.37 in. contacts to connect to the fire alarm or a life safety function. HORN HOUSING (137mm) 3.175 in. The power supply for horns,according to UL Listing,cannot 1 in.(81mm) (25mm) be connected to a UL Listed fire alarm system. For electrical 6 in. specifications see install book.RC models contain one set of Form (152mm) "C"dry contacts.Contacts rated 30 VAC/VDC 1 amp. SPACER E 8.875 in. 2 in. (225mm) (51mm) SIDE VIEW MODELS WITH HORN(STI-1100 Series) COVER Imo- (81 mm)5.34 in. I�3 in.) (76mm) 3.18 in. (136mm) 3.175 in. 4 in. 2.73 in.(81mm) �� .5 in. (102mm) 5 in. 2.32 in.(70mm) (13mm) 5.5 in. (127mm) 1.61 in.(59mm) 7.4 in. (140mm) (41mm) (188mm) 78 in. SPACER ADDS SPACER 2 in. _ 6.81 in. (20mm) 8.875 in.(225mm) (51m m) (173mm) 2"DEPTH�(SOmm) SIDE VIEW ALL MODELS END VIEW MODELS WITHOUT HORN(STI-3150 Series) EXTERNAL DIMENSIONS: •Flush 7.2 W x 10.2 H x 3.3 Din.(183x259x84mm) •Surface 7.2 W x 10.2 H x 5.5 D in.(183x259x140mm) Safety Techn Waterford,Michigan Fax:248-673-1246 � International �• . o• I *, www.sti-usa.com .I 3DR,England Printed in U.S.A.,0 1987-2020 Safety Technology International,Inc. Subject to change without notice. 05/21 DN-6720:E FMM-1 (A), FMM-101 (A), NOT 1 F 1 E R° FZM-1 (A) & FDM-1 (A) 0 Monitor Modules with FlashScan@ by Honeywell Intelligent/Addressable Devices General Four different monitor modules are available for Notifier's intelligent control panels for a variety of applications. Monitor modules supervise a circuit of dry-contact input devices, such as conventional heat detectors and pull stations, or monitor and power a circuit of two-wire smoke detectors ® MBE 0 M (FZM-1(A)) o..E. FMM-1(A) is a standard-sized module (typically mounts to a 4" [10.16 cm] square box) that supervises either a Style D pa;',a s«,•)„ (Class A) or Style B (Class B) circuit of dry-contact inputIAT devices. s" a°M,.•EPow...-.• "a. FMM-101(A) is a miniature monitor module a mere 1.3" (3.302 cm) H x 2.75"(6.985 cm)W x 0.65" (1.651 cm)D that "•'u' (�j (�� supervises a Style B (Class B) circuit of dry-contact input devices. Its compact design allows the FMM-101(A) to be mounted in a single-gang box behind the device it monitors. lo FZM-1(A) is a standard-sized module that monitors and supervises compatible two-wire, 24 volt, smoke detectors on a Style D(Class A)or Style B(Class B)circuit. FMM-1(A)(Type H) FDM-1(A)is a standard-sized dual monitor module that mon- itors and supervises two independent two-wire Style B(Class open dry-contact alarm activation devices. May also be used B)dry-contact initiating device circuits(IDCs)at two separate, to monitor normally-open supervisory devices with special consecutive addresses in intelligent,two-wire systems. supervisory indication at the control panel. Monitored circuit FlashScan® (U.S. Patent 5,539,389) is a communication may be wired as an NFPA Style B(Class B)or Style D(Class protocol developed by NOTIFIER that greatly increases the A) Initiating Device Circuit. A 47K Ohm End-of-Line Resistor speed of communication between analog intelligent devices. (provided) terminates the Style B circuit. No resistor is Intelligent devices communicate in a grouped fashion. If one required for supervision of the Style D circuit. of the devices within the group has new information, the FMM-1(A) OPERATION panel CPU stops the group poll and concentrates on single points. The net effect is response speed greater than five Each FMM-1(A)uses one of the available module addresses times that of other communication protocols. on an SLC loop. It responds to regular polls from the control panel and reports its type and the status(open/normal/short) �►FMM-1 A) Monitor Module of its Initiating Device Circuit(IDC).A flashing LED indicates that the module is in communication with the control panel. • Built-in type identification automatically identifies this The LED latches steady on alarm (subject to current limita- device as a monitor module to the control panel. tions on the loop). • Powered directly by two-wire SLC loop. No additional FMM-1(A)SPECIFICATIONS power required. • High noise(EMF/RFI)immunity. Nominal operating voltage: 15 to 32 VDC. • SEMS screws with clamping plates for ease of wiring. Maximum current draw: 5.0 mA(LED on). • Direct-dial entry of address: 01 —159 on FlashScan loops; Average operating current: 375 pA (LED flashing), 1 com- 01 —99 on CLIP loops. munication every 5 seconds,47k EOL. • LED flashes green during normal operation (programma- Maximum IDC wiring resistance: 1500 Ohms. ble option)and latches on steady red to indicate alarm. Maximum IDC Voltage: 11 Volts. The FMM-1(A) Monitor Module is intended for use in intelli- gent,two-wire systems,where the individual address of each EOL resistance:47K Ohms. module is selected using the built-in rotary switches. It pro- Temperature range: 32°F to 120°F(0°C to 49°C). vides either a two-wire or four-wire fault-tolerant Initiating Device Circuit(IDC)for normally-open-contact fire alarm and Humidity range: 10%to 93% noncondensing. supervisory devices.The module has a panel-controlled LED Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x indicator. The FMM-1(A) can be used to replace MMX-1(A) 1.25" (3.175 cm) deep. Mounts to a 4" (10.16 cm) square x modules in existing systems. 2.125"(5.398 cm)deep box. FMM-1(A)APPLICATIONS Use to monitor a zone of four-wire smoke detectors, manual fire alarm pull stations, waterflow devices, or other normally- DN-6720:E•07/30/2015—Page 1 of 4 FMM-101(A) Mini Monitor Module Temperature range: 32°F to 120°F(0°C to 49°C). • Built-in type identification automatically identifies this Humidity range: 10%to 93% noncondensing. device as a monitor module to the panel. Dimensions: 1.3" (3.302 cm)high x 2.75" (6.985 cm)wide x • Powered directly by two-wire SLC loop. No additional 0.65"(1.651 cm)deep. power required. Wire length: 6"(15.24 cm)minimum. • High noise(EMF/RFI)immunity. • Tinned,stripped leads for ease of wiring. FZM-1(A) Interface Module • Direct-dial entry of address: 01 —159 on FlashScan loops; Supports compatible two-wire smoke detectors. 01 —99 on CLIP loops. • Supervises IDC wiring and connection of external power source. 3 1415 0 1 ADDRESS 0 1 High noise(EMF/RFI)immunity. 12 3 g SEMS screws with clamping plates for ease of wiring. 11 0 4 LOOP O 4 Direct-dial entry entry of address: 01 — 159 on FlashScan 10 5 5 loops,01 —99 on CLIP loops. 9 8 7 6 9 8 7 6 LED flashes during normal operation; this is a program- TENS ONES mable option. • LED latches steady to indicate alarm on command from control panel. Y The FZM-1(A) Interface Module is intended for use in intelli- O Lu U gent, addressable systems, where the individual address of J O W � _J each module is selected using built-in rotary switches. This °Q module allows intelligent panels to interface and monitor two- wire conventional smoke detectors. It transmits the status (normal, open, or alarm) of one full zone of conventional detectors back to the control panel. All two-wire detectors being monitored must be UL compatible with the module. The FMM-101(A) Mini Monitor Module can be installed in a The FZM-1(A)can be used to replace MMX-2(A) modules in single-gang junction directly behind the monitored unit. Its existing systems. small size and light weight allow it to be installed without rigid FZM-1(A) APPLICATIONS mounting. The FMM-101(A) is intended for use in intelligent, two-wire systems where the individual address of each mod- Use the FZM-1(A) to monitor a zone of two-wire smoke ule is selected using rotary switches. It provides a two-wire detectors. The monitored circuit may be wired as an NFPA initiating device circuit for normally-open-contact fire alarm Style B (Class B) or Style D (Class A) Initiating Device Cir- and security devices. The FMM-101(A) can be used to cuit.A 3.9 K Ohm End-of-Line Resistor(provided)terminates replace MMX-101(A)modules in existing systems. the end of the Style B or D (class B or A) circuit (maximum IDC loop resistance is 25 Ohms). Install ELR across termi- FMM-101(A)APPLICATIONS nals 8 and 9 for Style D application. Use to monitor a single device or a zone of four-wire smoke FZM-1(A) OPERATION detectors, manual fire alarm pull stations, waterflow devices, or other normally-open dry-contact devices. May also be Each FZM-1(A) uses one of the available module addresses used to monitor normally-open supervisory devices with spe- on an SLC loop. It responds to regular polls from the control cial supervisory indication at the control panel. Monitored cir- panel and reports its type and the status (open/normal/short) cuit/device is wired as an NFPA Style B (Class B) Initiating of its Initiating Device Circuit(IDC).A flashing LED indicates Device Circuit. A 47K Ohm End-of-Line Resistor (provided) that the module is in communication with the control panel. terminates the circuit. The LED latches steady on alarm (subject to current limita- tions on the loop). FMM-101(A) OPERATION Each FMM-101(A) uses one of the available module FZM-1(A) SPECIFICATIONS addresses on an SLC loop. It responds to regular polls from Nominal operating voltage: 15 to 32 VDC. the control panel and reports its type and the status (open/ Maximum current draw: 5.1 mA(LED on). normal/short)of its Initiating Device Circuit(IDC). Maximum IDC wiring resistance: 25 Ohms. FMM-101(A) SPECIFICATIONS Average operating current: 270 NA, 1 communication and Nominal operating voltage: 15 to 32 VDC. 1 LED flash every 5 seconds, 3.9k eol. Average operating current: 350 pA, 1 communication EOL resistance: 3.9K Ohms. every 5 seconds, 47k EOL; 600 pA Max. (Communicating, IDC Shorted). External supply voltage (between Terminals T10 and T11): Maximum IDC wiring resistance: 1500 Ohms. •Maximum IDC Voltage: 11 Volts. DC voltage: 24 volts power limited. • Ripple voltage: 0.1 Vrms maximum. Maximum IDC Current: 450 NA. Current:90 mA per module maximum. EOL resistance:47K Ohms. Temperature range: 320F to 120OF(0°C to 490C). Page 2 of 4—DN-6720:E•07/30/2015 Humidity range: 10%to 93%noncondensing. Agency Listings and Approvals Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x In some cases, certain modules may not be listed by certain 1.25" (3.175 cm) deep. Mounts to a 4" (10.16 cm) square x approval agencies, or listing may be in process. Consult fac- 2.125"(5.398 cm)deep box. tory for latest listing status. FDM-1(A) Dual Monitor Module UL: S635. • ULC: S635. The FDM-1(A)Dual Monitor Module is intended for use in intelli- FM Approved. gent, two-wire systems. It provides two independent two-wire initiating device circuits (IDCs) at two separate, consecutive CSFM: 7300-0028:0219, 7165-0028:0224, addresses. It is capable of monitoring normally open contact fire 7165-0028:0243. alarm and supervisory devices; or either normally open or nor- MEA:457-99-E. mally closed security devices. The module has a single panel- controlled LED. U.S. Coast Guard: 161.002/50/0 (NFS2-640, NFS2-320, NOTE: The FDM-1(A)provides two Style B(Class B) 1DC circuits NFS2-3030). ONLY. Style D (Class A) IDC circuits are NOT supported in any Lloyd's Register: 11/600013 (NFS2-640, NFS2-320, application. NFS2-3030). FDM-1(A) SPECIFICATIONS Fire Dept. of New York: COA #6121 (NFS2-640, NFS- Normal operating voltage range: 15 to 32 VDC. 320), COA#6114(NFS2-3030). Maximum current draw: 6.4 mA(LED on). Product Line Information Average operating current: 750 pA(LED flashing). NOTE:"A"suffix indicates ULC-listed model. Maximum IDC wiring resistance: 1,500 Ohms. FMM-1(A): Monitor module. Maximum IDC Voltage: 11 Volts. FMM-101(A): Monitor module, miniature. Maximum IDC Current: 240 pA FZM-1(A): Monitor module,two-wire detectors. EOL resistance:47K Ohms. FDM-1(A): Monitor module, dual, two independent Class B Temperature range: 32°to 120°F(0°to 49°C). circuits. Humidity range: 10%to 93%(non-condensing). SMB500: Optional surface-mount backbox. NOTE: See installation instructions and refer to the SLC Wiring Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x Manual, PN 51253. 1.25" (3.175 cm) deep. Mounts to a 4" (10.16 cm) square x 2.125"(5.398 cm)deep box. FDM-1(A)AUTOMATIC ADDRESSING The FDM-1(A) automatically assigns itself to two address- able points, starting with the original address. For example, if the FDM-1(A)is set to address"26",then it will automatically assign itself to addresses"26"and"27". NOTE:"Ones"addresses on the FDM-1(A)are 0, 2,4, 6,or 8 only. Terminals 6 and 7 use the first address, and terminals 8 and 9 use the second address. A CAUTION: Avoid duplicating addresses on the system. Installation FMM-1(A), FZM-1(A), and FDM-1(A)modules mount directly to a standard 4" (10.16 cm)square, 2.125" (5.398 cm)deep, electrical box. They may also be mounted to the SMB500 surface-mount box. Mounting hardware and installation instructions are provided with each module. All wiring must conform to applicable local codes, ordinances, and regula- tions. These modules are intended for power-limited wiring only. The FMM-101(A) module is intended to be wired and mounted without rigid connections inside a standard electri- cal box. All wiring must conform to applicable local codes, ordinances,and regulations. DN-6720:E•07/30/2015—Page 3 of 4 FlashScan®and NOTIFIERO are registered trademarks and FireWatchT is a trademark of Honeywell International Inc. ©2015 by Honeywell International Inc.All rights reserved.Unauthorized use of this document is strictly prohibited. I�O 9001 This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. ENGINEERING&MANUFACTURING All specifications are subject to change without notice. QUALITY SYSTEMS For more information,contact Notifier.Phone:(203)484-7161,FAX:(203)484-7118. www.notifier.com Page 4 of 4—DN-6720:E•07/30/2015 DN-6931:A1 •1-304 5600 Series NOT 1 F 1 E R° Mechanical Heat Detectors by Honeywell DevicesConventional Initiating GENERAL System Sensor's 5600 Series mechanical heat detectors offer property protection against fire and for non-life-safety installa- tions,where smoke detectors are inappropriate. 7o] / o y Multiple configurations. The 5600 Series offers a full line of 0, -configurations to accommodate a broad range of applications. Both single- and dual-circuit models are offered, each avail- 1 able for low- and high-temperature ratings with either fixed- temperature or combination fixed-temperature/rate-of-rise (ROR) activation. The ROR element of the fixed/ROR models is restorable,to accommodate field-testing the unit. 6931 pha1.1P9 4 Installation flexibility. To satisfy a variety of installations, the 5600 Series easily mounts to single-gang and octagonal back- boxes. These models also accommodate 4" (101.6 mm) square backboxes when used with a plaster ring. The mount- ing bracket is reversible to allow for flush- and surface-mount backbox installations. SPECIFICATIONS Visual identification. The 5600 Series provides clear mark- PHYSICAL SPECIFICATIONS ings on the exterior of the unit to ensure that the proper detec- tor is being used. Alphanumeric characters identify the Maximum installation temperature: activation method, as well as the temperature rating, in For models 5601 P, 5603,5621,5623: 100°F(38°C). degrees Fahrenheit and Celsius. Fixed temperature models For models 5602,5604,5622,5624: 150°F(65.6°C). are identified "FX", while combination fixed/rate-of-rise units are marked "FX/ROR". The 5600 Series also provides a col- Alarm temperature: lector as a post-activation indicator. Once the detector has For models 5601 P, 5603,5621, 5623: 135°F(57°C). been activated, the collector drops from the unit to allow easy identification of the specific unit in alarm. For models 5602,5604, 5622,5624: 194°F(90°C). Rate-of-Rise Threshold: 15°F (8.3°C) per minute (models FEATURES 5601, 5602,5621,5622 only). • Multiple configurations available: Operating Humidity Range:5%to 95%RH noncondensing. —Fixed-temperature (non-resettable) or combination fixed Input Terminals: non-polarized, accept 14 to 22 AWG (2.0 to (non-resettable)/rate-of-rise(self-restoring). 0.33 mm2). —Low-temperature and high-temperature ratings. Dimensions: diameter with mounting bracket: 4.57" (116 mm); —Single-circuit and dual-circuit. height with mounting bracket: 1.69" (43 mm). • Easy-to-read alphanumeric identification of detector type Weight:6 oz. (170 grams). and temperature rating. Mounting Options: 3.5" (88.9 mm) octagonal backbox; 4" • External collector provides visual indication of activation. (101.6 mm) octagonal backbox; single-gang backbox; 4" • Reversible mounting bracket for flush- and surface-mount (101.6 mm) square backbox with a square-to-round plaster installations. ring. • Flexible mounting capabilities:single-gang,3.5"or 4"octag- ELECTRICAL SPECIFICATIONS onal,4" (101.6 mm)square with plaster ring. • Easy-to-use terminal screws provide a more positive wiring Operating Voltage Contact Ratings(resistive) connection. 6-125 VAC 3.0 A • Low-profile design to coordinate with room aesthetics. 6-28 VDC 1.0 A 125 VDC 0.3 A AGENCY LISTINGS AND APPROVALS 250 VDC 0.1 A These listings and approvals apply to the modules specified in Mechanical heat detector shall be a System Sensor 5600 this document. In some cases,certain modules or applications Series model number , Listed to Underwriters Labora- may not be listed by certain approval agencies, or listing may tories UL 521 for Heat Detectors for Fire Protective Signaling be in process.Consult factory for latest listing status. Systems.The detector shall be either a single-circuit or a dual- • UL Listed:S2101 circuit type,normally open.The detector shall be rated for acti- vation at either 135°F (57°C) or 194°F (90°C), and shall acti- • ULC Listed: S2101 (all with"A"suffix) vate by means of a fixed-temperature thermal sensor, or a • MEA: 199-03-E combination fixed-temperature/rate-of-rise thermal sensor. • CSFM: 7270-1209:227,7270-1653:167 The rate-of-rise element shall be activated by a rapid rise in • FM Approved temperature, approximately 15°F (8.3°C) per minute. The detector shall include a reversible mounting bracket for mount- DN-6931:A1•2/9/10—Page 1 of 2 ing to 3.5-inch (88.9 mm)octagonal,4-inch(101.6 mm)octag- ture rating and activation method. The rate-of-rise element of onal, single gang, and 4-inch (101.6 mm) square backboxes combination fixed-temperature/rate-of-rise models shall be with a square-to-round plaster ring. Wiring connections shall restorable,to allow for field-testing.The detectors shall include be made by means of SEMS screws that shall accommodate an external collector that shall drop upon activation to identify 14 — 22 AWG wire. The detector shall contain alphanumeric the unit in alarm. markings on the exterior of the housing to identify its tempera- ORDERING INFORMATION * Identification Temperature UL Protected Spacing, Model Method on Circuit Rating Activation 10'(3.048 m)Ceiling* Exterior 5601 P None Single 135°F(57°C) Fixed-Temperature/Rate-of-Rise 50 ft.x 50 ft.(15.24 m x 15.24 m) 5602 Lettering Single 194°F(90°C) Fixed-Temperature/Rate-of-Rise 50 ft.x 50 ft.(15.24 m x 15.24 m) 5603 Lettering Single I 135°F(57°C) Fixed-Temperature 25 ft.x 25 ft.(7.62 m x 7.62 m) 5604 Lettering Single 194°F(90°C) Fixed-Temperature 25 ft.x 25 ft.(7.62 m x 7.62 m) 5621 Lettering Dual 135°F(57°C) Fixed-Temperature/Rate-of-Rise 50 ft.x 50 ft.(15.24 m x 15.24 m) 5622 Lettering Dual 194°F(90°C) Fixed-Temperature/Rate-of-Rise 50 ft.x 50 ft.(15.24 m x 15.24 m) 5623 Lettering Dual 135°F(57°C) Fixed-Temperature 25 ft.x 25 ft.(7.62 m x 7.62 m) 5624 Lettering Dual 194°F(90°C) Fixed-Temperature 25 ft.x 25 ft.(7.62 m x 7.62 m) NOTE: Refer to NFPA 72 guidelines for spacing reductions When ceiling heights exceed 10 feet(3.048 m). *Add an"A"to part number for ULG model. WIRING DIAGRAMS Single-Circuit Models Control EOL Panel ORAuxilia + 6931 wir1.wmf ry Device EOL Control Panel Auxiliary Auxiliary Device U Device 16931wir2mmf OR- Auxiliary Auxiliary Dual-Circuit Models Device Device 02010 by Honeywell International Inc.All rights reserved.Unauthorized use of this document is strictly prohibited. I O 9001 This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. ffTT We cannot cover all specific applications or anticipate all requirements. ENGINEERING&MANUFACTURING All specifications are subject to change without notice. QUALITY SYSTEMS Made in the U.S.A. For more information,contact Notifier.Phone:(203)484-7161,FAX:(203)484-7118. www.notifier.com Page 2 of 2—DN-6931:A1•2/9/10 E,=1CL //=5 EIZOV=G W f BY SPACE AGE ELECTRONICS Hybrid Surge Protection Device An ideal choice for your 120VAC applications, the E120V-GT maintains system integrity and protects against transients introduced into electrical lines via poor atmospheric and utility conditions as well as internally generated inductive loads. FIRE ALARM EM-R-, Not only is the E-120V-GT robust enough to absorb a spike, but to also clamp long enough to trip the branch circuit breaker and still be functional for additional surges. Reduce downtime associated with power surges and lightning strikes, prevent interruption of recurring monthly revenue based systems, and �Vr UWpFO Features eliminate non-billable service calls and expensive repairs by protecting your equipment with this invaluable device. � • 120 VAC s,NCEA � • 10KA Short Circuit Current Rating Applications • ANSI/UL Listed 1449 4th • Fire alarm control panels Edition, Type 2 • Mass notification systems 0 • CSA C22.2 No. 269.2-17 • Dedicated branch circuits LISTED 2nd edition, Type 2 •Amplifiers, motors, pumps, and power boosters • Acerbox ELOCK Circuit Lockout Kit included per NFPA 72 2013 10.6.5.2 Specifications • Surface or conduit mounting All 120 VAC equipment will have Transient Voltage Surge • Diagnostic indicator light Suppression (TVSS) protection manufactured by Space Age Electronics, Inc., part number E120V-GT. The unit shall be ANSI/ • Self restoring UL listed to standard 1449, 4th edition and will be labeled • 3 Wire device(18" length) clearly with indelible ink. Can be attached via the 3/a" rigid coupling, or surface mounted via the 2 external mounting holes. The unit shall have thermal fuses to protect against fire in short circuit conditions and will have 18" long, 14 gauge wires(3x) with a green ground wire. The enclosure will be a non dielectric material UL94 QMFZ2/8 grade material providing UV protection. The unit shall provide visual indication (LED)that unit is protecting and functioning. Pg. 1/2 E=CL//=5 Performance Specifications Dimensions Short Circuit Current Rating (SCCR): 10kA � 3.5"�+ Enclosure Material: UL94 QMFZ2/8 (green) VPR=700 (L-N) 700 (L-G) 600 (N-G) Capacitance: < 2,000 pf ' Clamping Response Time: < 5 nanoseconds 21. Current: Non-Load Bearing wio Max Operating Voltage (MCOV): 140VAC, 50/60 Hz i Design:Thermally Fused Hybrid L6" Operation Indicators: LED a.a"� Max Surge Current: 25kA Energy Dissipation: 500J Clamping Voltage: 230V RMS Operating Specifications Wiring Diagram Service Voltage: 120VAC Single Phase Circuits Protected: L-N L-G N-G Breaker panel Connection Type: Hardwired o o Protected Device Installation Configuration: Parallel CM_ o 0 ®®_ N ®® p Compliance Specifications N G O GGGGGGs G O II O 1 O UL Listed: 1449 4th Edition - VZCA Ill- File Number: E319370 Vol. 1 Sec. 1 'g Ordering • • 120V Hybrid Surge Protection D-vice (ELOCK Circuit Lockoutincluded) Acerbox ELOCK • • www.lsae.com I toll free 1.800.486.1723 1 fax 508.485.4740 ©Copyright 2018 Space Age Electronics, Inc. I This document subject to change without notice LT10629 Rev.A NFPA non Pg.2/2 11- DITEK _ DTK-2MHLPF Series ® Modular Low Voltage Surge Protectors Surge Protection DITEK's DTK-2MHLPr Series of low voltage surge protectors provide robust protection in a compact package. t'9 Ala"jd This series was designed to remove load instead of shorting to ground. Convenient field-replaceable modules offer ease _ of installation, and the Snap-Track base system allows installers to protect multiple circuits while utilizing a common ground point. DTK-2MHLP24F DTK-2MHLP24FWB Technical Specifications Product Features DTK-2MHLP 5F 12F 24F 36F 48F EW Protects (2) low voltage circuit pairs Service Voltage: 5V 12V 24V 36V 48V 75V per module Hybrid design utilizing SAD and GDT MCOV: 6V 18V 33V 48V 64V 90V technologies Clamping Voltage: 6.8V 21.6V 39V 57V 76V 108V Opens circuit when compromised Protection Modes: Common Mode(L-G) Field-replaceable modular design with single point ground for fast and Surge Current Rating: 20,000A easy installation Max. Continuous 1A Six voltage configurations available Current: to protect various types of circuits Failure Mode: Open Circuit Hardwired multi-base mounting system allows protection for up to (10) pairs with a common ground Mechanic I Specifications Suitable for use on both AC and DC Base Connection Method: Hardwired terminals, 30-12 AWG low voltage circuits Module Connection Edge card into mounting base Method: Housing: ABS Applications Operating Temperature: -40°F- 158°F (-40°C-70°C) Fire Alarm Panel SLC, PIV and IDC Maximum Humidity: 95% non-condensing Circuits Module Module with Base Burglar Alarm Panel IDC Circuits Dimensions: 2.1"L x 1.4"W x 1.9"H 3.25"L x 1.5"W x 2.6"H 4-20mA Current Loops (53 mm x 36 mm x 48 mm) (83 mm x 38 mm x 66 mm) Weight: 1.2 oz(34 g) 2.8 oz(79 g) AccessorP— > To order module with base, add Standards Approvals "WB"to end of part number Certifications: UL497B Test Module Kit, p/n DTK-2MHLPTM Warranty: 10 Year Limited Warranty OMADE IN LISTED NFPA' J. S. A. DITEK Surge Protection,Largo,FL 337 11111111111111111111111111 Sales: 800-753-234 www.diteksurgeprotection.com ♦ SPS-100010-003 Rev 3 12/22 Every precaution has been taken to ensure that this literature is accurate and complete.DITEK Corporation assumes no responsibility and disclaims all liability for damages resulting from the use of this information or for any errors or omissions. DTK-2MHLPF Series bIIL L DITEK —pomp- Signaling Circuit Modular Surge Protectors 0 urge jft• t on mopwppp— Numbers • Dimensions Part #Pairs l+1 r�� Number Protected Dimensions I_ • ( 1 • 11 . g • • 1 : • • 11 • 1 1 91 u_ I n��• /• 5q /t1��'• �[� �1� p� /ICI ..c)=1 • -,•/.,, �`�� <l ��•��,7�� l'��l/II 0�1 �11• QOO��i "♦III • • A a t• o� 'r .. • • SYSTEM SENSOR° FI I I I F - Indoor Selectable- Output Horns, w tr n Strobes, and Horn Strobes for Wall Applications I System Sensor L-Series audible visible notification products are rich with features guaranteed to cut - t, installation times and maximize profits with lower 1 current draw and modern aesthetics. } '� Features • Updated Modern Aesthetics The System Sensor L-Series offers the most versatile and • Small profile devices for Horns and Horn Strobes easy-to-use line of horns,strobes,and horn strobes in the industry • Plug-in design with minimal intrusion into the back box with lower current draws and modern aesthetics.With white and red plastic housings,standard and compact devices,and plain, FIRE, • Tamper resistant construction and FUEGO-printed devices,System Sensor L-Series can • Automatic selection of 12-or 24-volt operation at 15 and 30 meet virtually any application requirement. candela • Field-selectable candela settings on wall units: The L-Series line of wall-mount horns,strobes,and horn strobes 15,30,75,95, 110, 135,and 185 include a variety of features that increase their application versatility • Horn rated at 88+dBA at 16 volts while simplifying installation.All devices feature plug-in designs • Rotary switch for horn tone and two volume selections with minimal intrusion into the back box,making installations fast and foolproof while virtually eliminating costly and time-consuming • Mounting plate for all standard and all compact wall units ground faults. • Mounting plate shorting spring checks wiring continuity before device installation To further simplify installation and protect devices from construction • Electrically compatible with legacy SpectrAlert and SpectrAlert damage,the L-Series utilizes a universal mounting plate for all Advance devices models with an onboard shorting spring,so installers can test wiring • Compatible with MDL3 sync module continuity before the device is installed. • Strobes and Horn Strobes listed for wall mounting only Installers can also easily adapt devices to a suit a wide range • Horns listed for wall or ceiling use of application requirements using field-selectable candela settings, automatic selection of 12-or 24-volt operation,and a rotary switch for horn tones with two volume selections. Agency Listings SIGNALING & F M ® APPROVED LISTED S5512 FM approved except 7125-1653:0504 S4011 for ALERT models 7135-1653:0503 3057383,3057072 AVDS865-05•2/22/2018•Page 1 L-Series Specifications General L-Series standard horns,strobes,and horn strobes shall mount to a standard 2 x 4 x 1 7/8-inch back box,4 x 4 x 11/2-inch back box,4-inch octagon back box,or double-gang back box.L-Series compact products shall mount to a single-gang 2 x 4 x 17/8-inch back box.A universal mounting plate shall be used for mounting ceiling and wall products for all standard models and a separate universal mounting plate shall be used for mounting wall compact models.The notification appliance circuit wiring shall terminate at the universal mounting plate.Also,L-Series products,when used with the Sync•Circuit'M Module accessory,shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts.When used with the Sync•Circuit Module, 12-volt-rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts;24-volt-rated notification appliance circuit outputs shall operate between 16.5 and 33 volts. Indoor L-Series products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full-wave rectified unfiltered power supply. Strobes and horn strobes shall have field-selectable candela settings including 15,30,75,95, 110, 135,and 185. Strobe The strobe shall be a System Sensor L-Series Model listed to UL 1971 and shall be approved for fire protective service.The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system. Horn Strobe Combination The horn strobe shall be a System Sensor L-Series Model listed to UL 1971 and UL 464 and shall be approved for fire protective service.The horn strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system.The horn shall have two audibility options and an option to switch between a temporal three pattern and a non-temporal(continuous)pattern.These options are set by a multiple position switch.The horn on horn strobe models shall operate on a coded or non-coded power supply. Synchronization Module The module shall be a System Sensor Sync•Circuit model MDL3 listed to UL 464 and shall be approved for fire protective service.The module shall synchronize Strobes at 1 Hz and horns at temporal three.Also,while operating the strobes,the module shall silence the horns on horn strobe models over a single pair of wires.The module shall mount to a 411/16 x 411/16 x 21/8-inch back box.The module shall also control two Style Y(class B)circuits or one Style Z(class A)circuit.The module shall synchronize multiple zones.Daisy chaining two or more synchronization modules together will synchronize all the zones they control.The module shall not operate on a coded power supply. Physical/Electrical Specifications Standard Operating Temperature 32°F to 120°F(0°C to 49°C) Humidity Range 10 to 93%non-condensing Strobe Flash Rate 1 flash per second Nominal Voltage Regulated 12 DC or regulated 24 DC/FWR1 Operating Voltage Range 8 to 17.5 V(12 V nominal)or 16 to 33 V(24 V nominal) Operating Voltage Range MDL3 Sync Module 8.5 to 17.5 V(12 V nominal)or 16.5 to 33 V(24 V nominal) Input Terminal Wire Gauge 12 to 18 AWG Wall-Mount Dimensions(including lens) 5.6-L x 4.7-W x 1.91-D(143 mm L x 119 mm W x 49 mm D) Compact Wall-Mount Dimensions(including lens) 5.26"L x 3.46"W x 1.91"D(133 mm L x 88 mm W x 49 mm D) Horn Dimensions 5.6-L x 4.7-W x 1.25-D(143 mm L x 119 mm W x 32 mm D) Compact Horn Dimensions 5.25"L x 3.45"W x 1.25"D(133 mm L x 88 mm W x 32 mm D) 1.Full Wave Rectified(FWR)voltage is a non-regulated,time-varying power source that is used on some power supply and panel outputs. 2.Strobe products will operate at 12 V nominal only for 15 cd and 30 cd. AVDS865-05.2/22/2018•Page 2 UL Current Draw Data UL Max.Strobe Current Draw(rnA RMS) UL Max.Horn Current Draw(rnA RMS) 8-17.5 Volts 16-33 Volts 8-17.5 Volts 16-33 Volts Candela DC DC FWR Sound Pattern dB DC DC FWR Candela 15 88 43 60 Temporal High 39 44 54 Range 30 143 63 83 Temporal Low 28 32 54 75 N/A 107 136 Non-Temporal High 43 47 54 95 N/A 121 155 Non-Temporal Low 29 32 54 110 N/A 148 179 3.1 KHz Temporal High 39 41 54 135 N/A 172 209 3.1 KHz Temporal Low 29 32 54 185 N/A 222 257 3.1 KHz Non-Temporal High 42 43 54 3.1 KHz Non-Temporal Low 28 29 54 Coded High 43 47 54 3.1 KHz Coded High 42 43 54 UL Max.Current Draw(rnA RMS),Wall Horn Strobe,Candela Range(115-185 cd) 8-17.5 Volts 16-33 Volts DC Input 15cd 30cd 15cd 30cd 75cd 95cd 110cd 135cd 185cd Temporal High 98 158 54 74 121 142 162 196 245 Temporal Low 93 154 44 65 111 133 157 184 235 Non-Temporal High 106 166 73 94 139 160 182 211 262 Non-Temportal Low 93 156 51 71 119 139 162 190 239 3.1 K Temporal High 93 156 53 73 119 140 164 190 242 3.1 K Temporal Low 91 154 45 66 112 133 160 185 235 3.11K Non-Temporal High 99 162 69 90 135 157 175 208 261 3.1 K Non-Temporal Low 93 156 52 72 119 138 162 192 242 16-33 Volts FWR Input 15cd 30cd 75cd 95cd 110cd 135cd 185cd Temporal High 83 107 156 177 198 234 287 Temporal Low 68 91 145 165 185 223 271 Non-Temporal High 111 135 185 207 230 264 316 Non-Temportal Low 79 104 157 175 197 235 283 3.1 K Temporal High 81 105 155 177 196 234 284 3.1 K Temporal Low 68 90 145 166 186 222 276 3.11K Non-Temporal High 104 131 177 204 230 264 326 3.1 K Non-Temporal Low 77 102 156 177 199 234 291 Horn Tones and Sound Output Data StrobeHorn and Horn • .: 8-17.5 16-33 Switch Volts Volts Position Sound Pattern dB DC DC FWR 1 Temporal High 84 89 89 2 Temporal Low 75 83 83 3 Non-Temporal High 85 90 90 4 Non-Temporal Low 76 84 84 5 3.1 KHz Temporal High 83 88 88 6 3.1 KHz Temporal Low 76 82 82 7 3.1 KHz Non-Temporal High 84 89 89 8 3.1 KHz Non-Temporal Low 77 83 83 9" Coded High 85 90 90 10" 3.1 KHz Coded High 84 89 89 "Settings 9 and 10 are not available on 2-wire horn strobes.Temporal coding must be provided by the NAC.If the NAC voltage is held constant,the horn output remains constantly on. AVDS865-05•2/22/2018•Page 3 L-Series Dimensions 1.91, 3.46" 3'46" 48.5 mm 88 mm 1.25" 3.57 1.55, 88 mm 1.25" 32 mm (9.1 cm) (3.9 cm) 32 mm 0 0� 0 001.4 0 0°6 UP o e e e°e a e°e oo 0°°°o°o0°°°0°0 eeeree ° 5.27" .e e e e e° °o°°°°°°°°°°° 5.38" 133.9 mm � 5.27" popopopapoQao (13.7 cm) O 133.9 mm °°°°°°°°°°° 0 eeeeaeeeoeeeo A0548-00 A0547-00 A0557-00 Compact Strobe,Horn Strobe Compact Horn Compact Wall Surface Mount Back Box SBBGRL,SBBGWL 4.70" (11.94 cm) 1.911, 4.7" __ 1.25" 1.25"cm) 119 mm 424 .69 c 1.25" 32 mm (12.24 cm) (4.69 cm) (3.18 mm) ic. oa00000° 68 cm)(14.4 cm) 144 mm °°°°° A0550-00 A0549-00 A0554-01 Strobe,Horn Strobe Horn Wall Surface Mount Back Box SBBRL/SBBWL L-Series Ordering Information Model Description Model Description Wall Horn Strobes Horns* ffP2W2-Wire,Horn Strobe,Red HRL* Horn,Red L 2-Wire,Horn Strobe,White HWL* Horn,White P2GRL 2-Wire,Compact Horn Strobe,Red HGRL* Compact Horn,Red P2GWL 2-Wire,Comp 2 fils act Horn Strobe,White HGWL* Compact Horn,White P2RL-P 2-Wire,Horn Strobe,Red,Plain Accessories P2WL-P 2-Wire,Horn Strobe,White,Plain TR-2 Universal Wall Trim Ring Red P2RL-SP 2-Wire,Horn Strobe,Red,FUEGO TR-2W Universal Wall Trim Ring White P2WL-SP 2-Wire,Horn Strobe,White,FUEGO SBBWL Wall Surface Mount Back Box,Red P4RL 4-Wire,Horn Strobe,Red SBBWL Wall Surface Mount Back Box,White P4WL 4-Wire,Horn Strobe,White SBBGWL Compact Wall Surface Mount Back Box, Red Wall Strobes SBBGWL Compact Wall Surface Mount Back Box,White SRL Strobe,Red SWL Strobe,White �SU� Compact Strobe,Red SGWL Compact Strobe,White SRL-P Strobe,Red,Plain SWL-P Strobe,White,Plain SRL-SP Strobe,Red,FUEGO SWL-CLR-ALERT Strobe,White,ALERT Notes: All-P models have a plain housing(no"FIRE"marking on cover). All-SP models have"FUEGO"marking on cover. All-ALERT models have"ALERT"marking on cover. *Horn-only models are listed for wall or ceiling use. SYSTEM3825 Ohio Avenue•St.Charles, IL 60174 ©2018 System Sensor. SENSORw Phone:800 SENSOR2•Fax:630 377 6495 Product rcurre current product sumatioct o change without nonce.version corn et. for current product information,including the latest version of this data sheet. www.systemsensor.com AVDS865-05.2122,/2018 SYSTEM SENSOR° Outdoor Selectable- ' R Output Horns, Strobes, and Horn Strobes for Wall Applications SPECTRAlert SpectrAIWO Advance outdoor audible visible products a n If AM IIIM c E are rich with features that cut installation times and maximize profits. Features SpectrAlert Advance offers the broadest line of outdoor horns, • Weatherproof per NEMA 4X, IP56 strobes,and horn strobes in the industry.With white or red plastic housings,wall or ceiling mounting options,and plain or FIRE-printed • Listed to UL 1638(strobe)and UL 464(horn) devices,SpectrAlert Advance can meet virtually any application • Compatible with System Sensor synchronization protocol and requirement, including indoor,outdoor,wet,and dry applications in legacy SpectrAlert products temperatures from—40oF to 151°F. • Field-selectable candela settings: 15, 15/75,30,75,95, 110, 115, 135, 150, 177,and 185 Like the entire SpectrAlert Advance line,outdoor horns,strobes, • Automatic selection of 12-or 24-volt operation at 15 and and horn strobes for wall applications include a variety of features 15/75 candela that increase application flexibility and simplify installation. First, • Rotary switch for horn tone and three volume selections field-selectable settings, including candela,automatic selection of 12-or 24-volt operation,horn tones,and three volume options enable • Horn rated at 88+dBA at 16 volts installers to easily adapt devices to meet requirements. • Rated from—40°F to 151°F • Universal mounting plate with an onboard shorting spring that Next,SpectrAlert Advance devices use a universal mounting plate tests wiring continuity before devices are installed for both wall and ceiling applications.This mounting plate includes • Plug-in design with minimal intrusion into the back box an onboard shorting spring that ensures wiring continuity before Tamper-resistant construction devices are installed,so installers can verify proper wiring without • mounting the devices and exposing them to potential construction • Listed for ceiling or wall mounting damage.Once the plates are mounted,all SpectrAlert Advance devices utilize a plug-in design with a single captured screw to speed installation and virtually eliminate costly ground faults. Outdoor devices ship with weatherproof plastic back boxes(metal back boxes are available separately)that accommodate in-and- Agency Listings out wiring for daisy chaining devices. Plastic back boxes feature removable side flanges and improved resistance to saltwater corrosion. Knock-outs located on the back eliminate the need to drill SIGNALING �0 holes for screw-in mounting. Plastic and metal weatherproof back ()� boxes come with 3/4-inch top and bottom conduit entries and 3/4-inch LISTED F M MEA 73001653:187(outdoor strobes) knock-outs at the back.A screw-in NPT plug with an 0-ring gasket approved 7125-1653:188(horn strobes, S4011(chimes,horn strobes,horns) APPROVED chime strobes) for a watertight seal is included with each back box. S3593(outdoor and alert strobes) 3093577 MEA452-05-E 7135-1653:189(horns,chimes) AVDS115-02•12/3/2019•Page 1 SpectrAlert Advance Outdoor Horn, Strobe, and Horn StrobeSpecifications General SpectrAlert Advance outdoor horns,strobes,and horn strobes shall mount to a weatherproof back box.A universal mounting plate shall be used for mounting ceiling and wall products.The notification appliance circuit wiring shall terminate at the universal mounting plate. Also,SpectrAlert Advance products,when used with the Sync•CircuitTM Module accessory,shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts.When used with the Sync•Circuit Module, 12-volt-rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts;24-volt-rated notification appliance circuit outputs shall operate between 16.5 and 33 volts.Outdoor SpectrAlert Advance products shall operate between-40 and 151 degrees Fahrenheit from a regulated DC or full- wave rectified unfiltered power supply.Strobes and horn strobes shall have field-selectable candela settings including 15, 15/75,30,75,95, 110, 115, 135, 150, 177,and 185. Strobe The strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and shall be approved for fire protective service. The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system.The strobe must be installed with its weatherproof back box in order to remain outdoor approved per UL.The strobe shall be suitable for use in wet environments. Horn Strobe Combination The horn strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and UL 464 and shall be approved for fire protective service.The horn strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system.The horn shall have three audibility options and an option to switch between a temporal three pattern and a non-temporal(continuous)pattern.These options shall be set by a multiple position switch. On four-wire products,the strobe shall be powered independently of the sounder.The horn or horn strobe models shall operate on a coded or non-coded power supply.The horn strobe must be installed with its weatherproof back box in order to remain outdoor approved per UL. The horn strobe shall be suitable for use in wet environments. Physical/Electrical Specifications Operating Temperature -40OF to 151 OF(-40°C to 66°C) Strobe Flash Rate 1 flash per second Nominal Voltage Regulated 12 DC/FWR or regulated 24 DC/FWR1 Operating Voltage Range 8 to 17.5 V(12 V nominal)or 16 to 33 V(24 V nominal) Operating Voltage with MLD3 Sync Module 8.5 to 17.5 V(12 V nominal)or 16.5 to 33 V(24 V nominal) Input Terminal Wire Gauge 12 to 18 AWG Wall-Mount Dimensions(including lens) 5.6-L x 4.7-W x 2.5-D(142 mm L x 119 mm W x 64 mm D) Horn Dimensions 5.6-L x 4.7-W x 1.3-D(142 mm L x 119 mm W x 33 mm D) Wall-Mount Weatherproof Back Box Dimensions(SA-WBB) 5.7-L x 5.1-W x 2.0-D(145 mm L x 130 mm W x 51 mm D) Notes: 1.Full Wave Rectified(FWR)voltage is a non-regulated,time-varying power source that is used on some power supply and panel outputs. 2.2.P,S,PC,and SC products will operate at 12 V nominal only for 15 and 15/75 cd. AVDS115-02.12/3/2019•Page 2 UL Current Draw Data UL Max.Strobe Current Draw(mA RMS) UL Max.Horn Current Draw(mA RMS) 8-17.5 Volts 16-33 Volts 8-17.5 Volts 16-33 Volts Candela DC FWR DC FWR Sound Pattern dB DC FWR DC FWR Standard 15 123 128 66 71 Temporal High 57 55 69 75 Candela 15/75 142 148 77 81 Temporal Medium 44 49 58 69 Range 30 NA NA 94 96 Temporal Low 38 44 44 48 75 NA NA 158 153 Non-Temporal High 57 56 69 75 95 NA NA 181 176 Non-Temporal Medium 42 50 60 69 110 NA NA 202 195 Non-Temporal Low 41 44 50 50 115 NA NA 210 205 Coded High 57 55 69 75 High 135 NA NA 228 207 Coded Medium 44 51 56 69 Candela 150 NA NA 246 220 Coded Low 40 46 52 50 Range 177 NA NA 281 251 185 NA NA 286 258 UL Max.Current Draw(mA RMS),2-Wire Horn Strobe,Standard Candela Range(15-115 cd) 8-17.5 Volts 16-33 Volts DC Input 15 15/75 15 15/75 30 75 95 110 115 Temporal High 137 147 79 90 107 176 194 212 218 Temporal Medium 132 144 69 80 97 157 182 201 210 Temporal Low 132 143 66 77 93 154 179 198 207 Non-Temporal High 141 152 91 100 116 176 201 221 229 Non-Temporal Medium 133 145 75 85 102 163 187 207 216 Non-Temporal Low 131 144 68 79 96 156 182 201 210 FWR Input Temporal High 136 155 88 97 112 168 190 210 218 Temporal Medium 129 152 78 88 103 160 184 202 206 Temporal Low 129 151 76 86 101 160 184 194 201 Non-Temporal High 142 161 103 112 126 181 203 221 229 Non-Temporal Medium 134 155 85 95 110 166 189 208 216 Non-Temporal Low 132 154 80 90 105 161 184 202 211 UL Max.Current Draw(mA RMS),2-Wire Horn Strobe,High Candela Range(135-185 cd) 16-33 Volts 16-33 Volts DC Input 135 150 177 185 FWR Input 135 150 177 185 Temporal High 245 259 290 297 Temporal High 215 231 258 265 Temporal Medium 235 253 288 297 Temporal Medium 209 224 250 258 Temporal Low 232 251 282 292 Temporal Low 207 221 248 256 Non-Temporal High 255 270 303 309 Non-Temporal High 233 248 275 281 Non-Temporal Medium 242 259 293 299 Non-Temporal Medium 219 232 262 267 Non-Temporal Low 238 254 291 295 Non-Temporal Low 214 229 256 262 Candela Derating Horn Tones and Sound Output Data For K series products used at low temperatures,listed Horn and Horn Strobe Output candela ratings must be reduced in accordance with •8-17.5 16-33 24-Volt Nominal this table. Switch Sound Volts Volts Reverberant Anechoic OutputStrobe Position Pattern dB DC FWR DC FWR DC FWR DC FWR Listed Candela Candela rating at—40°F 1 Temporal High 78 78 84 84 88 88 99 98 15 2 Temporal Medium 74 74 80 80 86 86 96 96 15/75 Do not use below 32°F 3 Temporal Low 71 73 76 76 83 80 94 89 30 4 Non- High 75 44 Temporal 82 82 88 88 93 92 100 100 95 70 5 Non- Medium 110 110 Temporal 78 78 85 85 90 90 98 98 115 115 6 Non- Low 75 75 81 81 88 84 96 92 135 135 Temporal 150 150 7t Coded High 82 82 88 88 93 92 101 101 177 177 8t Coded Medium 78 78 85 85 90 90 97 98 185 1185 9t Coded Low 75 75 81 81 88 85 96 92 tSettings 7,8,and 9 are not available on 2-wire horn strobe. SpectrAlert Advance Diagrams 119mm 64mm �4.7"� 2.5" 142mm 5.6- o O 0 Wall-Mount Horn Strobes Wall Plastic Weatherproof Back Box Wall-Mount Horn Strobe with Plastic SpectrAlert Advance Ordering Information Weatherproof Back Box ModelDescription White Wall Horn Strobes P2RK P2WK 2-Wire Horn Strobe,Standard cd,Outdoor(includes plastic weatherproof back box) P2RK-P P2WK-P 2-Wire Horn Strobe,Standard cd,Outdoor,Plain(includes plastic weatherproof back box) P2RK-R P2WK-R 2-Wire Horn Strobe,Standard cd,Outdoor(does not include plastic weatherproof back box) P2RHK P2WHK 2-Wire Horn Strobe,High cd,Outdoor(includes plastic weatherproof back box) P2RHK-P P2WHK-P 2-Wire Horn Strobe,High cd,Outdoor,Plain(includes plastic weatherproof back box) P2RHK-R P2WHK-R 2-Wire Horn Strobe,High cd,Outdoor(does not include plastic weatherproof back box) P4RK P4WK 4-Wire Horn Strobe,Standard cd,Outdoor(includes plastic weatherproof back box) P4RK-R — 4-Wire Horn Strobe,Standard cd,Outdoor(does not include plastic weatherproof back box) P2RHK-120 — 2-Wire Horn Strobe,High cd,Outdoor, 120 V(includes plastic weatherproof back box) Wall Strobes SRK SWK Strobe,Standard cd,Outdoor(includes plastic weatherproof back box) SRK-P SWK-P Strobe,Standard cd,Outdoor,Plain(includes plastic weatherproof back box) SRK-R SWK-R Strobe,Standard cd,Outdoor(does not include plastic weatherproof back box) SRHK SWHK Strobe,High cd,Outdoor(includes plastic weatherproof back box) SRHK-P SWHK-P Strobe,High cd,Outdoor,Plain(includes plastic weatherproof back box) SRHK-R SWHK-R Strobe,High cd,Outdoor(does not include plastic weatherproof back box) Horns HRK — Horn,Red,Outdoor(includes plastic weatherproof back box) HRK-R — Horn,Red,Outdoor(does not include plastic weatherproof back box) Accessories SA-WBB SA-WBBW Metal Weatherproof Back Box WTP WTPW Metal Weatherproof Outdoor Flush-mounting Plate Notes: All-P models have a plain housing(no"FIRE"marking on cover). All-R models require metal weatherproof outdoor flush mounting plate or a metal weatherproof outdoor back box(order separately)."Standard cd"refers to strobes that include 15,15/75,30,75,95,110,and 115 candela settings."High cd"refers to strobes that include 135,150,177,and 185 candela settings.When replacing standard outdoor units both the device and back box must be replaced. SYSTEM3825 Ohio Avenue•St.Charles, IL 60174 ©2019 System Sensor. Phone:800-SENSOR2•Fax:630-377-6495 Product specifications subject to change without notice.visit systemsensorcom SENSOR" y or current product information,including the latest version of this data sheet. www.s stemsensor.com nvos115-02.12/3/2019 i Community & Economic Development 18204 59th Avenue NE,Arlington,WA 98223 360-403-3551 W Today's Date Staff Requesting Refund Reason for Refund Choose an item. El Duplicate Payment November 6, 2023 N Charged in Error AHannah Hardwick _ zDate Charge Was Made Transaction Number �T - N Fire Plan Review Fee 1■rl Refund 006.345.83.00.02 ^/ November 3, 2023 157761942 ❑Other: Customer Name Customer Address Red Hawk Fire 917 134th Ave SW Ste. B- Everett,Wa, 98204 Protection 3 Description: Refund Permit Include proof of payment Amount: $100 Number: 5684 Applicant entered their valuation incorrectly which over charged them for the plan review fee. Should only be $100.Was charged $200. Approved By: Date: Permit#: 5684 Permit Date: 11/03/23 Permit Type: FIRE ALARM Project Name: Eagle Creek Elem School Portable P1 & P2 Applicant Name: Red Hawk Fire Protection Applicant Address: 917 134th Ave SW Ste. B-3 Applicant, City, Everett,WA 98204 State, Zip: Contact: James Pan Phone: 253-330-0736 Email:jamesp@redhawkfp.com Scope of Work: Install new fire alarm system in portable P1 & P2. Tie new system to existing fire alarm system in school. Existing school fire alarm sequence of operation remain the same. Valuation: 4800.00 Square Feet: 3400 Number of Stories: 1 Construction IA Type: Occupancy Group: E; Education ID Code: Permit Issued: Permit Expires: Form Permit Type: FIRE ALARM Status: Assigned To: Hannah Hardwick Property Parcel# Address Legal Description Owner Name Owner Phone Zoning ARLINGTON 31051200200300 1216 E 5TH ST SCHOOL DISTRICT 690 EDUCATION 16 Fees Fee Description Notes Amount Web Only-Fire System Plan RevicW Enter I irpermit is ror: Fire alarm,or fire $200.00 sprinkler Processing/Technology $25.00 FACP/Transmitter-New $200.00 FACP/Transmitter-Replace $125.00 Fire Alarm System Permit NFPA 72- 105.7.3 $375.00 Total $925.00 Attached Letters Date Letter Description 11/03/2023 %Vcb Form- B&iildingApplication Payments Date Paid By Description Payment Type Accepted By Amount 11/03/2023 XBP Conf: $200.00 157761942 Outstanding Balance $725.00 Uploaded Files Date File Name 11/03/2023 7184c 10042f9b1'6114l d776678db0227 1 264- 1 774-fire alarm eagle creek clan schgol .pdf 11/03/2023 b6a829cb26c3cdab297bec7c3cfd9c33 eagle creek portable pl p2 fas data sheets submittals rcv0.pdf 11/03/2023 254750b94462d6c10f67a9c3a22a9cfa eagle creek portable pl p2 fas drawings rev. pdf Q m U W W rn �-• Q a U on I� LL Wzwi h — OeE W � LU LU ��� � O GIZ [.fig� I' �i 4I � _�', • T K Nlip kc LU po ;_ r�l O r 1 1 w :.M Les k k o z a—o a— aCID a a a N > c r --� o � ykl�I f 1) t � 6 a 8 Ng �, �� � � u. 3 g « HK4 Gn`� 4,. m _ of LU J 'it l[OQ a �� usz O Z € � � Onis co HE g � �o � :'o � ohs oNooasa3allo� a aaaaueo CD jigas BE =3 W w ts P. V OD Q O ly rn g � � o� Q g� m 0� 9� C � ss� � a ��� o���vo8e o v � ��_� � tJJU.i Z W - Its VJ 93 LU )ITI ss � � _ � — (�� °° �a � 19 OCCJ W H Ld GI o F Magi o W LL O f p - Q V� W W 44 U W C/� Z fi G 2 O s N E f n cQj Y cn 0 6L z 3 3ws Nil airw�N g If a a g 9 g s 11 N ry MU IA 4 Q Z LL. L.L. MX. maX a U 9z �a ui - �, S}3 � w 6 N o 0 25 U� 15 w� MIA! 25 - � was s Lill w Q i m w w T rn ryry4 T LL F m 0 J a z oc i o d — o L �r CN �. o o LL w m L w _ J ^ o 1 m � !1 NEE Of Homo All a 0 y w w < oaor- - - ono _ - SIT UM¢ll D Q � Q mo N o N H�� N 00 U_ rn O � Q o �c I— 3 WI m o n oON ee. I z N� - Q 4 m J - 0 z =ILL S o h N sl U) 0 -TAW Ns"j p LU i S a m W (D LL r m o N� W o L.L ' Q z H L -� N — III o 0 x � � fo o m LL _L �) 'r o lot 0 E, w w w m Q o ¢ � m 0 o a a a - � d 0 I� -W ,o I- = 0El w a � x � w m x z c� 3 i a N 0 o coi w i z w i s P _ � 3 s` LL Permit#: 5684 Permit Date: 11/03/23 Permit Type: FIRE ALARM Project Name: Eagle Creek Elem School Portable P1 & P2 Applicant Name: Red Hawk Fire Protection Applicant Address: 917 134th Ave SW Ste. B-3 Applicant, City,Everett,WA 98204 State,Zip: Contact: James Pan Phone: 253-330-0736 Email:jamesp@redhawkfp.com Scope of Work: Install new fire alarm system in portable P1 &P2. Tie new system to existing fire alarm system in school. Existing school fire alarm sequence of operation remain the same. Valuation: 4800.00 Square Feet: 3400 Number of Stories: 1 Construction IA Type: Occupancy Group: E; Education ID Code: Permit Issued: 11/21/2023 Permit Expires: 05/20/2024 Form Permit Type: FIRE ALARM Status: COMPLETE Assigned To: Hannah Hardwick Property Parcel# Address Legal Description Owner Name Owner Phone Zoning ARLINGTON 31051200200300 1216 E 5TH ST SCHOOL DISTRICT 690 EDUCATION 16 Inspections Date Inspection Type Description Scheduled Date Completed Date Inspector Status 12/27/2023 FA00.FIRE ALARM 9AM Requested 01/05/2024 01/05/2024 BUILDING Approved FINAL Plan Reviews Date Review Type Description Assigned To Review Status 11/07/2023 FIRE ALARM BUILDING In Review Fees Fee Description Notes Amount Enter 1 if permit is for:fire alarm or fire Web Only-Fire System Plan Review sprinkler $200.00 Processing/Technology $25.00 FACP/Transmitter-New $200.00 FACP/Transmitter-Replace $125.00 Fire Alarm System Permit NFPA 72- 105.7.3 $375.00 Credit Card Service $6.00 Credit Card Service $21.75 Total $952.75 Attached Letters Date Letter Description 11/20/2023 Building Permit 11/03/2023 Web Form-Building Application Payments Date Paid By Description Payment Type Accepted By Amount 11/03/2023 XBP Conf: $200.00 157761942 11/03/2023 Chuan-Jen Pan 157761942 $6.00 11/21/2023 XBP Conf: $725.00 159109749 11/21/2023 Chuan-Jen Pan 159109749 Kristin Foster $21.75 Outstanding Balance $0.00 Notes Date Note Created By: 11/21/2023 sent permit for signature to applicant Hannah Hardwick Filled out refund request form for the overcharge of the plan review fee.Applicant entered 11/06/2023 Hannah Hardwick valuation incorrectly which overcharged the plan review fee. 11/06/2023 emailed applicant requesting hard copies of the plans Hannah Hardwick Uploaded Files Date File Name 11/21/2023 17565935-2023 BLD5684 IssuedPermit.pdf 11/06/2023 17406944-20231106 BLD5684 Refund Request Form.pdf 11/03/2023 7184e10042f9bf6ll4ld776678db0227 12641774-fire alarm eagle creek elem school pdf 11/03/2023 b6a829cb26e3edab297b8c7c3cfd9c33 eagle creek portable pl p2 fas data sheets submittals rev0.pdf 11/03/2023 254750b94462d6clOf67a9c3a22a9cfa eagle creek portable pl p2 fas drawings rev.0a.pdf