Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
4010 172ND ST_BLD6688_2026
merald Fire Fire Sprinkler Specialists 11505 Burnham Dr. NW Ste. 201 Gig Harbor, WA 98332 EmeraldFireLLC.com Phone: 253-857-2056 1 Fax: 253-857-2312 Walmart Arling ton 4010 172nd ST NE, Arlington, WA 98223 Fire Sprinkler Product Submittal Data Walmart Arlington Fire Sprinkler Product Submittal Data Table of Contents Sprinklers • Tyco TY323 TY-FRB 155* K5.6 QRP Hangers/Bracing • Tolco Fig. 99 Threaded Rod • Tolco Fig. 200 Swivel Ring Hanger • Tolco Fig. 980 Seismic Attachment • Tolco Fig. 4A Seismic Brace • Tolco Fig. 1001 Seismic Brace • Tolco Fig. 828 Flange Seismic Attachment • PHD Fig. 353 & 354 Top Beam Clamp • PHD Fig. 358 Retaining Straps Pipe/Fittings • Boursann Mannessman Sch.10 & Sch.40 Black Pipe • Victaulic Firelock Grooved Fittings • Victaulic Mechanical T Bolted Branch Outlets • Victaulic Firelock 009 Grooved Coupling • Victaulic Firelock 004 Grooved Flexible Coupling • Anvil SPF Ductile Iron Threaded Fittings tqCOWorldwide Fire Protection Contacts www.tyco-fire.com Products Series TY-FRB, 5.6 K-factor Recessed Pendent Sprinklers Quick Response, Standard Coverage General The TYCO Series TY-FRB Sprinklers T' Description described herein must be installed and maintained in compliance with this doc- The TYCO Series TY-FRB,5.6 K-factor, ument, as well as with the applicable and Pendent (TY323) standards of the National Fire Protec- Sprinklers described in this data sheet tion Association,in addition to the stan- are quick response,standard coverage, dards of any other authorities having decorative 3 mm glass bulb-type spray jurisdiction. Failure to do so may impair sprinklers designed for use in light or the performance of these devices. ordinary hazard,commercial occupan- cies such as banks, hotels, and shop- The owner is responsible for maintain- ping malls. ing their fire protection system and devices in proper operating condition. The recessed version of the Series TY- The installing contractor or sprinkler FRB Pendent Sprinkler,where applica- manufacturer should be contacted with ble, is intended for use in areas with a any questions. finished ceiling.This recessed pendent I sprinkler uses one of the following- Sprinkler �Z • A two-piece Style 15 Recessed Escutcheon with recessed adjust- Identification r ment up to 5/8 inch (15,9 mm) from the flush pendent position. Number (SIN) • A two-piece Style 20 Recessed Escutcheon with recessed adjust- -ISjP _ ment up to 1/2 inch (12,7 mm) from TY323 . . . . . . Pendent 5.61K, 1/2-NPT the flush pendent position. The adjustment provided by the Technical Recessed Escutcheon reduces the Temperature Rating accuracy to which the fixed pipe drops Data o to the sprinklers must be cut. 155-F(68oC) Intermediate level versions of Series Approvals o TY-FRB Sprinklers are described in UL and C-UL Listed �E} Technical Data Sheet TFP357. Sprin- FM, LPCB, and VdS Approved kler guards and shields are described CE Certified Finishes in Technical Data Sheet TFP780. Sprinklers with Polyester Finish are UL Sprinkler: Refer to Table A and C-UL Listed as Corrosion-Resis- Recessed Escutcheon:White Coated, tant Sprinklers. Chrome Plated, or Brass Plated Maximum Working Pressure Physical Characteristics 175 psi (12.1 bar) Frame. . . . . . . . . . . . . . . . . . . Bronze 250 psi(17.2 bar)" Button. . . . . . . . . . . . . .Brass/Copper *The maximum working pressure of 250 psi Sealing Assembly. . . . . . . . .Stainless IMPORTANT (17.2 bar)only applies to the listing by Un- Steel w/TEFLON Always refer to Technical Data derwriters Laboratories, Inc.(UL). Bulb . . . . . . . . . . . . . . . . . . . . . .Glass Sheet TFP700 for the "INSTALLER Discharge Coefficient Compression Screw. . . . . . . . Bronze WARNING"that provides cautions K=5.6 GPM/psi1/2(80,6 LPM/bar1/2) Deflector. . . . . . . . . . . . . . . . . Bronze with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and installation can permanently dam- age a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. Page 1 of 4 FEBRUARY 2014 TFP172 TFP172 Page 2 of 4 Components: *Temperature rating is ** Pipe thread connections per ISO 7-1 1 Frame 4 - Bulb indicated on Deflector. can be provided on special request. 2 Button 5 - Compression STYLE 15 or 20 3 Sealing Screw ESCUTCHEON PLATE 1/2" 7/16" (11,1 mm) RECESSED Assembly 6 - Deflector* DEFLECTOR* SEATING SURFACE NPT** NOMINAL MAKE-IN ESCUTCHEON 6* I 5 7/16" (11,1 mm) 4 NOMINAL 2" � _I � h MAKE-IN (50,8 mm) 2 2" �1 n 1-3/8" 3 (50,8 mm) (34,9 mm) 1 WRENCH / FLATS 1 1/2" NPT** EFLECTOR* 2-7/8" (73,0 mm)DIA. CROSS SECTION UPRfGI IT PENDENT RECESSED PENDENT FIGURE 1 SERIES TY-FRB )AND PENDENT(TY323)SPRINKLERS 5.6 K-FACTOR, 112 INCH NPT, QUICK RESPONSE Operation Installation /\ The glass bulb contains a fluid which The TYCO Series TY-FRB,5.6 K-factor, WR H RECESS expands when exposed to heat.When a�Pendent (TY323) (USE ONLY the rated temperature is reached, the Sprinklers must be installed in accor- END"A") fluid expands sufficiently to shatter the dance with this section. glass bulb, allowing the sprinkler to activate and water to flow. General Instructions FIGURE 2 Do not install any bulb-type sprinkler if W-TYPE 6 the bulb is cracked or there is a loss SPRINKLER WRENCH Design of liquid from the bulb.With the sprin- kler held horizontally, a small air bub- WRENCH Criteria ble should be present. The diameter of the air bubble is approximately 1/16 RECESS The TYCO Series TY-FRB, 5.6 K-factor, inch (1,6 mm)for the 135°F(57°C)and Upright (T and Pendent (TY323) 3/32 inch(2,4 mm)for the 286°F(141°C) Sprinklers are intended for fire protec- temperature ratings. tion systems designed in accordance with the standard installation rules rec- A leak-tight 1/2 inch NPT sprinkler joint ognized by the applicable Listing or should be obtained by applying a min- Approval agency(such as, UL Listing imum to maximum torque of 7 to 14 t is ft.-Ibs. (9,5 to 19,0 Nm). Higher levels based the requirements of NFPA of torque can distort the sprinkler Inlet 13, and FMM Approval is based on the PUSH WRENCH requirements of FM's Loss Prevention with consequent leakage or impairment Data Sheets).Only the Style 15 or Style of the sprinkler. IN TO ENSURE 20 Recessed Escutcheon is to be used Do not attempt to compensate for ENGAGEMENT for recessed pendent installations. insufficient adjustment in the Escutch- WITH SPRINKLER WRENCHING AREA eon Plate by under-or over-tightening FIGURE 3 the sprinkler. Re-adjust the position of the sprinkler fitting to suit. W-TYPE 7 RECESSED SPRINKLER WRENCH Upright and Pendent Sprinklers The Series TY-FRB Upright and Pen- dent Sprinklers must be installed in accordance with the following instructions. Step 1. Install Pendent sprinklers in the pendent position. Install upright sprin- klers in the upright position. Step 2. With pipe-thread sealant applied to the pipe threads, hand- tighten the sprinkler into the sprinkler fitting. TFP172 Page 3of4 Step 3. Tighten the sprinkler into the 2-7/8" DIA. _ sprinkler fitting using only the W-Type (73,0 mm) 6 Sprinkler Wrench(Figure 2).With ref- erence to Figure 1, apply the W-Type 6 2-1/4" DIA. Sprinkler Wrench to the wrench flats. FACE OF (57,2 mm) Torque sprinklers 7 to 14 ft.-Ibs. (9,5 to SPRINKLER 19,0 Nm). FITTING Recessed Pendent Sprinklers FLUSH The Series TY-FRB Recessed Pendent 3/8 5/16" Sprinklers must be installed in accor- (9,5 7,9 mm) L1 dance with the following instructions. Step A.After installing the Style 15 or } MOUNTING 1/8" Style 20 Mounting Plate over the sprin- SURFACE (3,2 mm) kler threads, and with pipe-thread sealant applied to the pipe threads, CLOSURE SERIES MOUNTING 1-3/8" (34,9 mm) hand-tighten the sprinkler into the TY-FRB PLATE sprinkler fitting. 3/4"(19,1 mm) FIGURE 4 Step B. Tighten the sprinkler into the SERIES TY-FRB RECESSED PENDENT SPRINKLER ASSEMBLY(TY323) sprinkler fitting using only the W-Type WITH TWO PIECE 518 INCH TOTAL ADJUSTMENT STYLE 15 7 Recessed Sprinkler Wrench (Figure RECESSED ESCUTCHEON 3).With reference to Figure 1,apply the W-Type 7 Recessed Sprinkler Wrench to the sprinkler wrench flats. Torque 2-7/8" DIA. sprinklers 7 to 14 ft.-Ibs. (9,5 to 19,0 (73,0 mm) Nm). FACE OF Step C.After ceilinginstallation and fin- SPRINKLER 2-1/4" DIA. ishing, slide on the tyle 15 or Style 20 FITTING (57,2 mm) Closure over the Series TY-FRB Sprin- 5/16 1/4" 1/2"(12,7 mm) kler and push the Closure over the (7,g 6,4 mm) Mounting Plate until its flange comes in FLUSH contact with the ceiling. r J Care and MOUNTING 1/8 Maintenance SURFACE (3,2 mm) The TYCO Series TY-FRB,5.6 K-factor, Upright (TY313)and Pendent (TY323) CLOSURE SERIES MOUNTING 1-3/8" (34,9 mm) Sprinklers must be maintained and ser- TY-FRB PLATE 7/8"(22,2 mm) viced in accordance with this section. FIGURE 5 Before closing a fire protection system SERIES TY-FRB RECESSED PENDENT SPRINKLER ASSEMBLY(TY323) main control valve for maintenance WITH TWO PIECE 112 INCH TOTAL ADJUSTMENT STYLE 20 work on the fire protection system RECESSED ESCUTCHEON that it controls, obtain permission to shut down the affected fire protection Modified sprinklers must be replaced. standards of any other authorities hav- systems from the proper authorities Sprinklers that have been exposed to ing jurisdiction. Contact the installing and notify all personnel who may be corrosive products of combustion, but contractor or sprinkler manufacturer affected by this action. have not operated, should be replaced regarding any questions. Absence of the outer piece of an if they cannot be completely cleaned Automatic sprinkler systems are rec- escutcheon, which is used to cover by wiping the sprinkler with a cloth or ommended to be inspected, tested, a clearance hole, can delay sprinkler by brushing it with a soft bristle brush. and maintained by a qualified Inspec- operation in a fire situation. Care must be exercised to avoid dam- tion Service in accordance with local The owner must assure that the sprin- age to the sprinklers before,during,and requirements and/or national codes. klers are not used for hanging any after installation. Sprinklers damaged objects and that the sprinklers are only by dropping, striking, wrench twist/ cleaned by means of gently dusting slippage,or the like, must be replaced. with a feather duster; otherwise, non- Also, replace any sprinkler that has a operation in the event of a fire or inad- cracked bulb or that has lost liquid from vertent operation may result. its bulb. (Ref. Installation Section.) Sprinklers which are found to be leak- The owner is responsible for the ing or exhibiting visible signs of corro- inspection,testing,and maintenance of sion must be replaced. their fire protection system and devices in compliance with this document, as Automatic sprinklers must never be well as with the applicable standards painted, plated, coated, or other- of the National Fire Protection Associa- wise altered after leaving the factory. tion (e.g., NFPA 25), in addition to the TFP172 Page 4of4 P/N* 77 - XXX - X - XXX SPRINKLER TEMPERATURE FINISH RATINGS SIN } NATURAL BRASS 4,95 186-F(67-G) 370 c 6K i iPRIGHT(112-NPT) TV313 g 155 155°F(68°C) PG VESTER 371 5.6K PENDENT(1/2""NPT) TY323 4 SIGNAL WI 11TE(RAI=9008)oni YESTER a7� �) Use suffix"I"for ISO 7-1 connection; 9 CHROME PLATED 299 —^_^_°F(98-G` for example,77-370-4-175-I '*Eastern Hemisphere sales only 2$6 286-F{441°G) TABLE A SERIES TY-FRB UPRIGHT AND PENDENT SPRINKLERS PART NUMBER SELECTION Limited Ordering Warranty Procedure For warranty terms and conditions,visit Contact your local distributor for avail- www.tyco-fire.com. ability.When placing an order, indicate the full product name and Part Num- ber(P/N). Sprinkler Assemblies with NPT Thread Connections Specify:Series Pen- dent (specify) Sprinkler, SIN (specify), K=5.6, Quick Response, (specify)tem- perature rating, (specify) finish, P/N (specify, refer to Table A). Recessed Escutcheon Specify:Style 15 Recessed Escutcheon with(specify")finish, P/N(specify') Specify: Style 20 Recessed Escutch- eon with(specify")finish, P/N(specify') Refer to Technical Data Sheet TFP770 Sprinkler Wrench Specify: W-Type 7 Sprinkler Wrench, P/N 56-850-4-001 GLOBAL HEADQUARTERS 1400 Pennbrook Parkway,Lansdale,PA 19446 Telephone+1-215-362-0700 Copyright©2014 Tyco Fire Products,LP. All rights reserved. t[�CO TEFLON is trademark of The DuPont Corporation. Fire Protection Products EASY FLOW FIRE SPRINKLER PIPES Borusan Mannesmann is the first manufacturer in Europe and Turkey who has been UL listed and FM Why EASY FLOW fire Easy Flow fire sprinkler pipes approved according to EN standards since 2015 and UL listed and FM approved according to ASTM standards since2007. sprinkler pipes? have perfect roundness. Easy Flow fire sprinkler pipes are UL and FM When all pipes are connected to each other,perfect In recent years,the importance of fire protections systems has increased significantly due to regulations and certified according to EN and ASTM standards.Due alignment occurs and there is no weld gap to be legislations in Occupational Health and Safety area.Fire protection systems have been disseminating in to having high product quality and accredited by filled. Fast, comfortable and secure pre-weld houses,shopping malls,airports and industrial facilities.In Europe over 4.000 and in the U.S over 3.500 lives international institutions,the use of Easy Flow fire preparation is done.It is easy to make butt-welding are lost annually as a result of fire injuries.Consequently,fire protection measures have become an sprinkler pipes provides economic advantages in and it saves labor,time and cost. increasingly vital matter. terms of insuring the buildings against fire. 00 Borusan Mannesmann,a solution partner of its customers in the areas of black,galvanized and grooved pipes,is proud to be the avant-garde of fire protection pipes. Easy Flow fire sprinkler pipes have 1 layer(up to 30 micron) Easy Flow fire sprinkler pipes can be used in wet extinguishing systems including fire cabinet,hydrant and of sand blasted varnish sprinkler systems.Alternatively,BM pipes have applications in sparkling,gas and dry chemical extinguishing systems for fire protection purposes. coating. Special Procedures Applied On Request Advantages Of Easy Flow Fire v��/�/ 1-Provides corrosion protection for 6 months until Sprinkler Pipes I Underwriters Laboratories(UL);is an international independent engineering and security company that tests the final layer is coated. In order to reuse the S Customized pipe length a UL and FM approved in EN standards the compliance of fire-safety systems with fire safety standards for the building elements of the system.UL corroded pipe,sandblasting and painting processes U Production of special steel grades/qualities ig UL and FM approved in ASTM A53 and is headquartered in the USA and serves in 6 continents;it operates in five main strategic areas including are necessary.In some cases,pipes may not be Inner/Out r Epoxy Coating A795 standards. product safety,environment,health,university and verification services.Thousands of types of products, used where atmospheric rust has progressed and W Sandblasting and Primer Coating a It can be produced as black bare,primer materials,and systems are scientifically assessed,tested,and approved by UL in compliance with the risks deep corrosion has occurred.Easy Flow provides W Outer PE(polyethylene)Coating coated(black,gray and red colors)and of electricity,fire,and injury.On the other hand,FM(Factory Mutual);is an independent technical unit of the long lasting fire protection system,provides low 0 Galvanization galvanized. FMI Company that insures great risks such as fire,natural disasters and it certifies the performance of the overhead costs and saves time,labor and scrap. - U Grooving ig The red primer has high adhesion and it is materials and systems.FM performs risk and insurance calculations through engineering analysis,which is resistant to corrosion,water and oil. different from the analysis prepared by insurance statisticians for many years. 2- The priming process applied to Easy Flow a With options of Plain End,Threaded& products is done immediately after the production Coupled or Grooved. Fire protection systems designed by using UL and FM approved system elements(pipe,valve,pump,sprinkler, of pipes.The primer is applied to the adherence S Weld bead can be removed upon request. etc.)avoids,life and property losses and provide economic advantages in insuring buildings against fire. surface without contamination of foreign matter CE certified. such as dirt,dust,etc.before the atmospheric rust Borusan Mannesmann is the first steel pipe manufacturer which have UL and FM certificates according to EN is farmed.Therefore,Easy Flow fire sprinkler pipes standards in Europe. am better quality and long lasting and provide savings from costs of maintenance/repair. About Borusan Mannesmann Inside weld bead is removed a 6 World-Class Plants in Turkey,US and Italy for grooved Easy Flow fire ig Perfect Product Quality with Lean 6 Sigma sprinkler pipes. Production Technique __ a Wide Product Range with High Quality During grooving process,the weld bead causes _ S Exceeding Limits with Continuous R&D measurement deviations and errors in grooved area. -- av Excellent Service with Voice Of Customer Such deflections may cause the seal not to be fully L seated,the clamps not being fully tightened,or even Process all leakages.Easy Flow grooved fire sprinkler pipes Well established sales organization K r. provide perfect connection and combination during 3 Export to more than 35 countries - assembly and also fully compatible with Victaulic S UL and C-UL listed,FM approved,NSF and and Atusa standards. DVGW certified ig Integrated Delivery Services ASTM FM&UL EN FM&UL Nominal OD Wall Wall Weigh Weight FM UL OD Wall FM UL Technical Specifications EASY • Sixes Imm) Thickness Thickn ss (live) Ike/mt PE) (mm) thickn .�1 ROII Gfooved FI (inch (achl /maJ Immj ss - SPRINKLER z,so py FM Approved ,v4 az,z 0.1oz 2e0 ,,n zss ! 33,] 26 aUUC-ULUated 0 Easy Flow 11M 48.3 0.102 2.fi0 1,9] 2.93 ! a24 2,3 ! &1 NFS Certified Li9M wall 2 60,9 0.114 2,90 2]6 4,10 42p 2,6 21/2 73 2,90 3,52 5,23 40,3 2,0 • a Custom Length Availability J - 48,3 ! by ASTM A53/A795 and EN production standards n e9a 0,26 3,20 ss0 9,63 J 1PIPES m.3 o 13a 3?o zse n,a3 Li9M ! 0 Tght tolerances = - 1 39.4 a.o]e 2:00 toy tss wau Bo,3 z,o n/4 e.o]e zoo ,,3a J 76,1 z,1e J .91 Consistent roundness --- scH 7 49,3 O.oea 2,13 sa 2,99 ! ! a Consistent wall thickness r` 12 80,3 0.00a 2,13 1,93 2,08 1 2 in ]3 0.086 2,18 2,6] 3.9] ! COn515tent straightness 9 B8,9 0e. 2,36 3,38 5.04 114,3 2,6 .91 Weldable 41/4" 41 22o 2:10 4,61 ].,s J ff o69 2 ! e1 O J 0 Pressure Tested , - 0.109 2.]] 1,01 2.69 ! a Reliable high steel quality 1 vz•• 4es 6.1oe 2a7 zos 9.n J J a Galvanised or shop primer coated black,red z^ fig3 oe 2:77 s4 3,a3 J J J J oo wan cM uL (RAL 3000,RAL 3002 and Rai 3009)or grey 212 8839 0.120 3,05 4:34 6,6 J ! (mm) Thbkness (RAL 7012) SGH 10 31M" 101.6 0.120 3,05 4,98 ].41 ! J (mm) 4•• 14 ouzo a,os ss2 ea] J 3a] 32 .`y CE,PED Certified s•• 2n 3,2 e ,41,3 0.1. 3,4 9,30 13,85 ! J E� 48,3 " 219,1 0.108 a,]0 18,98 25.26 J J 603 36 10" 2]3.1 0.180 4.]8 21,23 31,62 J J Ma9 m 76,1 9,6 •' - 11Z' W.4 114 2,10 J 869 114' a2,2 0.117 J 114,3 4,5 / ! 1 1M" .,30.12s 3,10 2,3] 3,53 ! 2" fi0,3 0.125 3,18 3,00 4,40 ! tbsl s,0 J J 21/2" ]3 0.188 4,]8 5,40 8.04 sCH 30 3" 089 4,7e 2 ! ,01,8 4,18 9,41 J 34� 1,4,3 0.100 a,]0 0,69 12,91 J 0" 219.1 0.2]] ],04 24,]0 36,01 ! OD Walle FM UL 10" 2]3.1 0,307 7,8 .24 51,03 J (mm) Tnick s 1�,' s23.8 8138 438] J Imml s 17 27 1 3v4" 2fi7 0.113 2,87 1,13 169 J ! M 3,2 1 _ 1" 33,4 0.133 3.38 1.. 2,50 ! J 33,7 4,0 1 11 42,2 0,140 3,56 2:2] 3.38 J EN 112 3,88 10255 I 0.11 J Heaw 60,3 a,5 T 1F2" ]33 a.- 5,16 s:'. Q64 J ! ]6,1 4,5 ! SCH 40 3" B0,9 0.216 SA9 ],58 11,29 ! J 312" 101.6 0.2. 5,]4 9,12 13,58 J 184,3 5,4 9.7 14,:3 0.258 a,s 4,63 21,09 J ! 185,, s,a ! 168.3 0.280 7,11 18,99 28.29 J J 0" 219.1 0322 8.18 30.45 45,34 I 11" ,1 s ] ,s2 A leading European producer of steel pipes,Borusan Mannesmann is the choice of customers across Europe, 1/2 21's 4] 3,91 °e the US and Canada for industrial and residential fire rotection s nkler s stem es. 3/4"- 0.154 t4] P pri Y P P,4 0.179 a,55 2,19 32s6,1e1 ass 3,. 4qs Factory Mutual approved,Underwriters Laboratories&Canadian UL listed,ASTM A53/A795 and EN 2" 0,200 s,08 3,65 5,sCH� production standard Borusan Mannesmann sprinkler pipes...To enhance the safety of your projects with the z1rz 39 0.a0o ],01g75 , professional service and high quality assurance of Borusan Mannesmann,known all over the world. 31/2" 101.E 0.318 0,8 ,02 oBpRUSAN4' 114,3 0.33] 8,W 15,20 22,605: 14,.3 9.3]5 9,52 21,64 31,42BORUSAN �� ►�E-mail:export®bomsan.comJa L_ • ®�/••••Qeso9 ;9;;o aa;oo ss:a, wwv-raaanmannesm�nann.cpm MANNESMANN -V•LVy -. \�// MANNESMANN aaa m Victaulic° FireLockT" Fittings ✓ct—au licr 10.03 1.0 PRODUCT DESCRIPTION Available Sizes • 11/4—8"/DN32—DN200 Maximum Working Pressure • Pressure ratings for Victaulic FireLockTM Fittings conform to the ratings of Victaulic Fire Lock EZTM Style 009N couplings (refer to publication 10.64 for more information). Application • FireLockTM fittings are designed for use exclusively with Victaulic couplings that have been Listed or Approved for Fire Protection Services. Use of other couplings or flange adapters may result in bolt pad interference. • Connects pipe, provides change in direction and adapts sizes or components Pipe Materials • Carbon steel 2.0 CERTIFICATION/LISTINGS e@us < FM> 0LPcB VdS UK C E C A O usre" EN 10311 BS EN 10311 CPR(EU) CPR(UK) No.305/2011 2019 No.465 3.0 SPECIFICATIONS— MATERIAL Fitting: Ductile iron conforming to ASTM A536, Grade 65-45-12. Fitting Coating: (specify choice) ❑ Orange coating. ❑ Red coating(standard for EMEA-1 and Asia Pacific). ❑ Optional: Hot dipped galvanized. ALWAYS REFER TO ANY NOTIFICATIONS AT THE END OF THIS DOCUMENT REGARDING PRODUCT INSTALLATION,MAINTENANCE OR SUPPORT. victaulic.com 10.03 1539 Rev P Updated 07/2022 ©2022 Victaulic Company.All rights reserved. 1 �ctaulic victaulic.com 4.0 DIMENSIONS �CtoE� toE� I p oE C j p- p fa-0 C T t � o ele to � o o � No.001 No.003 No.002 No.006 No.001 No.003 No.002 No.006 90'Elbow 45'Elbow Straight Tee Cap Actual Approximate Approximate Approximate Approximate Nominal Outside Weight Weight Weight Weight Size Diameter C to E Each C to E Each C to E Each T Each inches inches inches lb inches lb inches lb inches lb ON mm I mm kg mm kg I mm kg mm kg 11/4 1.660 - - - - 0.82 0.3 DN32 42.4 - - - - - 21 0.1 11/2 1.900 0.82 0.4 DN40 48.3 - - - - - - 21 0.2 2 2.375 2.75 1.7 2.00 1.8 2.75 2.4 0.88 0.6 DN50 60.3 70 0.8 51 0.8 70 1.1 22 0.3 21/2 2.875 3.00 3.1 2.25 2.2 3.00 3.6 0.88 1.0 73.0 76 1.4 57 1.0 76 1.6 22 0.5 3.000 3.00 3.30 2.25 2.4 3.00 3.8 DN65 76.1 76 1.5 57 1.1 76 1.7 3 3.500 3.38 4.0 2.50 3.1 3.38 5.3 0.88 1.2 DN80 88.9 86 1.8 64 1.4 86 2.4 22 0.5 4.250 4.00 5.7 3.00 5.1 4.00 7.5 108.0 102 2.6 76 2.3 102 3.4 4 4.500 4.00 6.7 3.00 5.6 4.00 8.7 1.00 2.4 DN100 114.3 102 3.0 76 2.5 102 3.9 25 1.1 5 5.563 4.88 12.6 3.25 8.3 4.88 15.7 1.00 4.1 141.3 124 5.7 83 3.8 124 7.1 25 1.9 5.500 4.88 12.4 3.25 8.2 4.88 15.4 DN125 139.7 124 5.6 82.6 3.7 124 6.9 6.250 5.50 12.6 3.50 9.2 5.50 17.9 158.8 140 5.7 89 4.2 140 8.0 6 6.625 5.50 18.3 3.50 11.7 5.50 22.7 1.00 5.9 DN150 168.3 140 8.3 89 5.3 140 10.3 25 2.7 6.500 5.43 17.6 3.50 11.4 5.50 22.0 165.1 140 7.9 89 5.2 140 9.9 8 8.625 6.81 25.5 4.25 20.4 6.94 38.7 1.13 12.7 DN200 219.1 173 11.6 108 9.3 176 17.6 29 5.8 8.515 6.81 23.1 - - 6.94 33.6 - - 216.3 173 10.5 - - 176 15.2 - - 10.03 1539 Rev P Updated 07/202 ©2022 Victaulic Company.All rights reserved. victaulic.com 2 ✓ct-au lic victaulic.com 5.0 PERFORMANCE Flow Data Size Frictional Resistance Equivalent of Straight Pipe' No.002 Actual Elbows Straight Tee Nominal Outside No.001 No.003 Size Diameter 90,Elbow 45'Elbow Branch Run inches inches feet feet feet feet D N m m meters meters meters meters 1 1/4 1.660 - - - DN32 42.4 - - 1 1/2 1.900 - - - - DN40 48.3 - - - - 2 2.375 3.5 1.8 8.5 3.5 DN50 60.3 1.1 0.5 2.6 1.1 21/2 2.875 4.3 2.2 10.8 4.3 73.0 1.3 0.7 3.3 1.3 3.000 4.5 2.3 11.0 4.5 DN65 76.1 1.4 0.7 3.4 1.4 3 3.500 5.0 2.6 13.0 5.0 DN80 88.9 1.5 0.8 4.0 1.5 4.250 6.4 3.2 15.3 6.4 108.0 2.0 0.9 4.7 2.0 4 4.500 6.8 3.4 16.0 6.8 DN100 114.3 2.1 1.0 4.9 2.1 5 5.563 8.5 4.2 21.0 8.5 141.3 2.6 1.3 6.4 2.6 5.500 8.3 4.1 20.6 8.3 DN 125 139.7 2.5 1.3 6.3 2.5 6.250 9.4 4.9 25.0 9.6 158.8 2.9 1.5 7.6 2.9 6 6.625 10.0 5.0 25.0 10.0 DN 150 168.3 3.0 1.5 7.6 3.0 6.500 9.8 4.9 24.5 9.8 165.1 3.0 1.5 7.5 3.0 8 8.625 13.0 5.0 33.0 13.0 DN200 219.1 4.0 1.5 10.1 4.0 8.515 13.0 - 33.0 13.0 216.3 4.0 - 10.1 4.0 The flow data listed is based upon the pressure drop of Schedule 40 pipe. 10.03 1539 Rev P Updated 07/202 ©2022 Victaulic Company.All rights reserved. victaulic.com 3 ✓ctaul�c victaulic.com 6.0 NOTIFICATIONS General Notes NOTE: When assembling Fire Lock EZTM couplings onto end caps, take additional care to make certain the end cap is fully seated against the gasket end stop. For Fire Lock EZTM Style 009N/009H couplings, use FireLockTM No. 006 end caps containing the "EZ" marking on the inside face or No. 60 end caps containing the "QV EZ" marking on the inside face. Non-Victaulic end cap products shall not be used with Style 009/009V/009H/009N couplings. 7.0 REFERENCE MATERIALS 10.64:Victaulic®FireLockTM Rigid Coupling Style 009N 10.02,Victaulic®FireLockTM Rigid Coupling Style 005H with Vic-PIUSTM Gasket System 29.01:Victaulic@ Terms and Conditions of Sale User Responsibility for Product Selection and Suitability Note Each user bears final responsibility for making a determination as to the suitability of This product shall be manufactured by Victaulic or to Victaulic specifications.All products Victaulic products for a particular end-use application,in accordance with industry to be installed in accordance with current Victaulic installation/assembly instructions. standards and project specifications,and the applicable building codes and related Victaulic reserves the right to change product specifications,designs and standard regulations as well as Victaulic performance,maintenance,safety,and warning equipment without notice and without incurring obligations. instructions.Nothing in this or any other document,nor any verbal recommendation, Installation advice,or opinion from any Victaulic employee,shall be deemed to alter,vary,supersede, Reference should always be made to the Victaulic installation handbook or installation or waive any provision of Victaulic Company's standard conditions of sale,installation instructions of the product you are installing.Handbooks are included with each shipment guide,or this disclaimer. of Victaulic products,providing complete installation and assembly data,and are available Intellectual Property Rights in PDF format on our website at www.victaulic.com. No statement contained herein concerning a possible or suggested use of any material, Warranty product,service,or design is intended,or should be constructed,to grant any license Refer to the Warranty section of the current Price List or contact Victaulic for details. under any patent or other intellectual property right of Victaulic or any of its subsidiaries or affiliates covering such use or design,or as a recommendation for the use of such Trademarks material,product,service,or design in the infringement of any patent or other intellectual Victaulic and all other Victaulic marks are the trademarks or registered trademarks of property right.The terms"Patented"or"Patent Pending"refer to design or utility patents Victaulic Company,and/or its affiliated entities,in the U.S.and/or other countries. or patent applications for articles and/or methods of use in the United States and/or other countries. 10.03 1539 Rev P Updated 07/202 ©2022 Victaulic Company.All rights reserved. victaulic.com 4 ✓ctaulic Mechanical-TO Boixed Branch Outlets @ <FM> @ VdS LPCB VNIIPO SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS STYLES 920 AND 920N Victaulic Mechanical-TO Outlet provides a direct branch connection at any location a hole can be cut in pipe.The hole is cut oversize to receive a "holefinder" locating collar which secures the outlet in position permanently.A pressure responsive gasket seals on the pipe O.D. Cross-type connections can be achieved by utilizing two upper housings of the same style and size,with the same or differing branch size connections. NOTE:Style 920 and Style 920N housings cannot be mated to each other to achieve a cross connection. 5 4 Style 920 and Style 920N Mechanical-T outlets are available with grooved or female threaded STYLES 920 AND 920N STYLE 920 CROSS outlet.Specify choice on order. Units are supplied painted with plated bolts.Galvanized hous- PATENTED ings are available,supplied with plated bolts. All sizes of Style 920 and 920N are rated at 500psi/345OkPa working pressure on Schedule 10 and 40 carbon steel pipe.They may also be used on high density polyethylene or poly- butylene(HDPE)pipe. Pressure ratings on HDPE are dependent on the pipe rating.Contact Victaulic for ratings on other pipe.Style 920 and 920N are not recommended for use on PVC plastic pipe. Standard piping practices dictate that the Mechanical-T Styles 920 and 920N must be installed so that the main and branch connections are a true 90°angle when permanently attached to the pipeline surface. Additionally,the Vic-Tap II®hole cutting tool,which allows for hole cutting capabilities on pressurized systems,utilizes the Style 920 Mechanical-T in conjunction with the Series 726 Vic-Ball Valve to create the Style 931 Vic-Tap II Mechanical-T unit.See page 8 for further information. MATERIAL SPECIFICATIONS Housing/Coating:Ductile iron conforming to ASTM A-536,grade 65-45-12,with orange enamel coating. Ductile iron conforming to ASTM A-395,grade 65-45-15, is available upon special request. • Optional: Hot dipped galvanized Gasket:(Specify choice*) • Grade"E" EPDM EPDM(Green color code).Temperature range—30oF to+230oF/-34oC to+110°C. Recommended for cold and hot water service within the specified temperature range plus a variety of dilute acids,oil-free air and many chemical services. UL Classified in accordance with ANSI/NSF 61 for cold+86*F/+30°C and hot+180°F/+82°C. NOT RECOMMENDED FOR PETROLEUM SERVICES. • Grade"T"nitrile Nitrile(Orange color code).Temperature range—20°F to+180°F/-29°C to+82°C. Recommended for petroleum products,air with oil vapors,vegetable and mineral oils within the specified temperature range. Not recommended for hot water services over+150°F/+66°C or for hot dry air over+140°F/+60°C. *Services listed are General Service Recommendations only. It should be noted that there are services for which these gaskets are not recommended. Reference should always be made to the latest Victaulic Gasket Selection Guide for specific gasket service recommendations and for a listing of services which are not recommended. Bolts/Nuts: Heat-treated plated carbon steel,trackhead meeting the physical and chemical requirements of ASTM A-449 and physical requirements of ASTM A-183. JOB/OWNER CONTRACTOR ENGINEER System No. Submitted By Spec Sect Para Location Date Approved Date www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY.©2018 VICTAULIC COMPANY.ALL RIGHTS RESERVED. / toulice REV_O 11.02_1 CARBON STEEL PIPE- HOLE CUT PRODUCTS 11.02 Mechanical-TO Bolted Branch Outlets STYLES 920 AND 920N DIMENSIONS DiameterAppr x. Size Dimensions Weight Each Nominal Size Inc hes '0.13 Inches Inches Inches Inches Inches Inches �y rZ� mm �� mm mro mm rom - 2 x Yz(a)° 920N Soo 1.50 2.00 2.53 1.61 5.35 2.75 3.1 50 15 3450 38.1 51 64 41 136 70 1.5 V /4(a)a 920N 500 1.50 1.97 2.53 _ 1.61 5.35 2.75 3.1 20 3450 38.1 50 64 41 136 70 1.5 1(a)a 920N 500 1.50 1.85 2.53 _ 1.61 5.35 2.75 3.0 W 25 3450 38.1 47 64 41 136 70 1.4 y 1 Y4(a)to 920N 500 1.75 2.05 2.75 3.00 1.61 5.35 3.00 3.5 3.2 oil iT GROOVED OUTLET 32 3450 44.5 52 70 76 41 136 76 1.7 1.5 1�/z(a)to 920N 500 1.75 2.03 2.75 3.12 1.61 5.35 3.25 3.6 3.2 40 3450 44.5 52 70 79 41 136 83 1.7 1.5 Y �Z 25 x Yz(1 §a 920N SOo L50 2.21 2.74 _ 1.82 143 2.0 3.4 65 a) 3450 1.5 .1 70 - 46 1.6 70 .4 3/4(a)§a 920N 500 1.50 2.18 2.74 1.82 5.64 2.75 3.0 V 20 3450 38.1 55 70 46 143 70 1.4 TT 1(a)§a 500 1.50 2.06 2.74 _ 1.82 5.64 2.75 2.9 4 25 920N 3450 38.1 52 70 46 143 70 1.4 w 1114 t(a)n 920N 500 1.75 2.30 3.00 3.25 1.82 6.29 3.00 3.5 3.2 32 3450 44.5 58 76 83 46 160 76 1.7 1.5 FEMALE THREADED OUTLET 1 Yz t(a)a 920N 500 2.00 2.28 3.00 3.25 1.82 6.26 3.25 3.6 3.3 40 3450 50.8 58 76 83 46 159 83 1.7 1.6 Yz(a) 300 1.50 2.22 2.75 2.25 6.46 3.18 3.9 76.1 x 15 920N 2065 38.1 56 70 57 164 81 1.8 • Provides a direct branch connection at 1/4(a) 300 1.50 2.19 2.75 2.25 6.46 3.18 3.9 any location where a hole can be cut 20 920N 2065 38.1 56 70 - 57 164 81 1.8 in the pipe 1(a) 920N 300 1.50 2.07 2.75 2.25 6.46 3.18 3.8 25 2065 38.1 53 70 57 164 81 1.7 • A pressure responsive gasket provides 1'/4(a)o 920N 500 1.75 2.30 3.00 3.31 1.92 6.29 3.00 3.5 3.2 the seal 32 3450 44.5 58 76 84 49 160 76 1.6 1.5 1 Yz(a)a 920N 500 2.00 2.28 3.00 3.31 1.92 6.29 3.25 3.5 3.3 • Request Publication 11.03 for 40 3450 50.8 58 76 84 49 160 83 1.6 1.5 Mechanical-T cross assemblies 3 1/2(a)a 500 1.50 2.52 3.05 _ 2.28 6.15 2.75 3.4 _ 80 x 15 920N 3450 38.1 64 78 58 156 70 1.6 • Pressure rated up to 500 psi/3450 kPa Y4(a)a 920N 500 1.50 2A9 3.05 2.28 6.15 2.75 3.4 on steel pipe; also available for use 20 3450 38.1 63 78 58 156 70 1.6 with HDPE pipe 1(a) 920N 500 1.50 2.38 3.06 _ 2.28 6.15 2.75 3.3 25 3450 38.1 61 78 58 156 70 1.6 • Sizes from 2 x 1/2750 x 15 mm 1 Y4(a)to 920N 500 1.75 2.55 3.25 3.56 2.28 6.15 3.00 3.8 3.7 through 8 x 47200 x 100 mm 32(b) 3450 44.5 65 83 90 58 156 76 1.8 1.8 1/z(a)to 920N 500 2.00 2.78 3.50 3.56 2.28 6.15 3.25 4.1 3.8 40(b) 3450 50.8 71 89 90 58 156 83 1.9 1.8 2(a)a 920N 500 2.50 2.75 3.50 3.56 2.28 6.75 3.88 4.9 4.6 50 3450 63.5 70 89 90 58 172 99 2.3 2.1 31/2 x 2 920N 500 2.50 3.00 _ 3.75 2.44 6.72 3.88 _ 3.8 90 50 3450 63.5 76 95 62 171 99 1.8 IMPORTANT NOTES: TABLE CONTINUED ON PG.3 Style 920 and Style 920N housings cannot be **Center of run to engaged pipe end,female threaded outlet only(dimensions approximate). mated to one another t Available with grooved or female threaded outlet.Specify choice on order. to achieve cross connections. # Center of run to end of fitting. # Female threaded outlets are available to NPT and BSPT specifications. @ See page 7 for Fire Protection approvals and pressure ratings. (a)British Standard female pipe threaded outlet is available as listed.Specify"BSPT clearly on order. (b)For 76.1 mm threaded outlet,specify 21/2'BSPT clearly on order. §Vds approved for fire protection services a LPCB approved for fire protection services 0 Approved for use in China by Tianjin Approvals Company. www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY.©2018 VICTAULIC COMPANY.ALL RIGHTS RESERVED. iCt9uI-we 11.02_2 REV_O CARBON STEEL PIPE-HOLE CUT PRODUCTS 11.02 Mechanical-r Bolted Branch Outlets STYLES 920 AND 920N DIMENSIONS size Awl' Dimensions Run x Branch Hole Vt Y Z -!A -0.00 n1m n1m mm RIM n mm Inches +0.13 Inches Inches Inches Inches InchE s Inches no mm TABLE CONTINUED FROM PAGE 2 4 Yz(a) 500 1.50 3.03 3.56 2.69 7.01 2.75 3.7 - V 100 x 15 920N 3450 38.1 77 90 - 68 178 70 1.8 - 3/4(a)11 920N 500 1.50 3.00 3.56 2.69 7.01 2.75 3.7 20 3450 38.1 76 90 68 178 70 1.8 y 1(a)a 920N 500 1.50 2.88 3.56 _ 2.69 7.01 2.75 3.6 25 3450 38.1 73 90 68 178 70 1.8 GROOVED OUTLET 1 Y4(a)to g20N 500 1.75 3.08 3.78 4.00 2.69 7.01 3.00 4.0 3.6 32(b) 3450 44.5 78 96 102 68 178 76 1.9 1.8 1112(a)to 920N 500 2.00 3.28 4.00 4.00 2.69 7.01 3.25 4.2 3.9 Y Z 40(b) 3450 50.8 83 102 102 68 178 83 2.0 1.9 2(a)tR 920N 500 2.50 3.25 4.00 4.00 2.69 7.01 3.88 5.0 4.6 50 3450 63.5 83 102 102 68 178 99 2.3 2.1 V 2'/2(a)t 920 500 2.75 2.88 4.00 4.00 2.69 7.34 4.63 5.8 5.0 T� 65 3450 69.9 73 102 102 68 186 118 2.6 2.3 T 76.1 mm 920 500 2.75 2.88 4.00 2.69 7.34 4.63 6.4 w 3450 69.9 73 102 68 186 118 2.9 3(a)t 500 3.50 3.31 4.50 4.12 2.69 7.73 5.12 8.4 6.4 80 920 3450 88.9 84 114 105 68 196 130 3.8 2.9 FEMALE THREADED OUTLET 1 1/4(a)n 500 1.75 3.08 3.78 2.63 7.64 3.05 5.0 108.0 x 32 920N 3450 44.5 78 96 67 194 78 2.3 1 h(a)0 920N 500 2.00 3.28 4.00 _ 2.63 7.64 3.25 5.0 • Provides a direct branch connection at 40 3450 50.8 83 102 67 194 83 2.3 _ any location where a hole can be cut 2(a) 920N 500 2.50 3.25 4.00 _ 2.63 7.64 4.00 4.0 in the pipe 50 3450 63.5 83 102 67 194 102 1.9 76.1 mm 920 500 2.75 2.88 4.00 4.00 2.63 7.64 4.29 8.0 789.9 73 102 102 67 194 109 3.6 3.5 the seal 3(a) 920 500 3.50 3.31 4.50 4.50 2.63 7.63 4.88 6.8 6.5 80 3450 88.9 84 114 114 67 194 124 3.1 3.0 • Request Publication 11.03 for 5 1/2(a)t 500 2.00 4.03 4.75 4.75 3.16 9.70 3.69 7.4 7.6 Mechanical-T cross assemblies 125 x 40 920 3450 50.8 102 121 121 80 246 94 3.4 3.4 2(a)t 500 2.50 4.00 4.75 4.75 3.16 9.70 4.38 8.2 8.0 • Pressure rated up to 500 psi/3450 kPa 50 920 3450 63.5 102 121 121 80 246 111 3.7 3.6 on steel pipe; also available for use 21/2(a)t 920 500 2.75 3.63 4.75 4.75 3.16 9.70 4.63 8.3 7.9 with HDPE pipe 65 3450 69.9 92 121 121 80 246 118 3.8 3.6 76.1 mm❑ 920 500 2.75 3.75 _ 4.75 3.16 9.70 4.63 _ 8.0 • Sizes from 2 x V2750 x 15mm 3450 69.9 95 121 80 246 118 3.6 through 8 x 47200 x 100mm 3(a)t 920 500 3.50 3.81 5.00 4.63 3.16 9.70 5.31 8A 8.8 80 3450 88.9 1 97 127 118 80 246 135 3.8 4.0 2 500 2.50 3.75 4.50 _ 3.17 8.00 3.88 8.0 _ 33.0 x 50 920N 3450 63.5 95 114 81 203 99 3.6 3 920 500 3.50 3.81 5.00 _ 3.00 9.46 5.31 8.0 80 3450 88.9 97 127 76 240 1 135 3.6 TABLE CONTINUED ON PG.4 IMPORTANT NOTES: **Center of run to engaged pipe end,female threaded outlet only(dimensions approximate). Style 920 and Style 920N housings cannot be t Available with grooved or female threaded outlet.Specify choice on order. mated to one another t Center of run to end of fitting. to achieve cross connections. # Female threaded outlets are available to NPT and BSPT specifications. @ See page 7 for Fire Protection approvals and pressure ratings. (a)British Standard female pipe threaded outlet is available as listed.Specify"BSPT"clearly on order. (b)For 76.1 mm threaded outlet,specify 2/2"BSPT clearly on order. §Vds approved for fire protection services n LPCB approved for fire protection services 0 Approved for use in China by Tianjin Approvals Company. www.victaulic.com iCtaiLJliL'* VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY.©2018 VICTAULIC COMPANY.ALL RIGHTS RESERVED. REV_O 11.02_3 CARBON STEEL PIPE- HOLE CUT PRODUCTS 11.02 Mechanical-TO Bolted Branch Outlets STYLES 920 AND 920N DIMENSIONS Size Dimensions Nominal Size RIDiameter T-s Thd. Gry.. W y Z Inches '0.13 Inche Inches Inche Inches Inches Inches E Y 00 mm mm mm mm mm mm Win TABLE CONTINUED FROM PAGE 3 1 Y2 t 500 2.00 3.78 4.50 3.30 8.23 3.25 7.0 V 139.7 x 40 920N 3450 50.8 96 114 84 209 83 3.2 - 2 t 920N 500 2.50 3.75 4.50 3.30 8.23 3.88 9.0 - 50 3450 63.5 95 114 84 209 99 4.1 w 6 1 Y4(a) 500 1.75 4.43 5.13 5.13 3.79 9.15 3.25 5.1 4.8 5- "R 150 x 32(b) 920N 3450 44.5 112 130 130 96 232 83 2.3 2.2 GROOVED OUTLET 11/2(a)to 920N Soo 2.00 4.40 5.13 5.13 3.79 9.15 3.25 5.4 5.1 40(b) 3450 50.8 112 130 130 96 232 83 2.4 2.3 2(a)to 920N 500 2.50 4.38 5.13 5.13 3.79 9.15 3.88 6.0 5.6 50 3450 63.5 111 130 130 96 232 99 2.7 2.5 Y Z 65 920 500 69.9 110 130 130 94 10.51 118 8.3 3.4 65 3450 69.9 110 130 130 94 267 118 3.8 3.4 V 500 2.75 4.15 _ 5.21 3.69 10.51 4.63 _ 8.4 T 3450 69.9 105 132 94 267 118 3.8 3(a)t 920 500 3.50 4.31 5.50 5.13 3.69 10.51 5.31 9.9 8.4 w 80 3450 88.9 110 140 130 94 267 135 4.5 3.8 4(a)to 920 500 4.50 3.81 5.75 5.38 3.69 10.51 6.25 10.1 10.1 76.1 mm a 920 100 3450 114.3 97 146 137 94 267 159 4.6 4.6 FEMALE THREADED OUTLET 11/z(a) :-- 2.00 4.41 130 _ 3.63 9.40 3.25 7.8 _ 159.0 x 40 920N 3450 T50.8 112 130 92 239 83 3.5 2(a) 920N 500 2.50 4.38 5.13 _ 3.63 9.40 3.88 8.0 • Provides a direct branch connection at 50 3450 63.5 111 130 92 239 99 3.6 any location where a hole can be cut 76.1 mm 920 500 2.75 4.38 5.50 5.13 3.63 9.40 4.63 9.5 9.5 in the pipe 3450 69.9 111 140 130 92 239 118 4.3 4.3 3 500 3.50 4.31 5.50 5.13 3.63 9.40 5.31 8.1 14.0 • A pressure responsive gasket provides 80 920 3450 88.9 110 140 130 92 239 135 3.7 6.4 the seal 108.Omm 920 500 4.50 4.45 _ 5.38 3.63 9AO 6.12 _ 10.0 3450 114.3 113 1 137 92 239 155 4.5 • Request Publication 11.03 for 4 500 4.50 3.81 1 5.75 3.63 9.40 6.25 18.0 Mechanical-T cross assemblies 100 920 3450 114.3 96.80 146 - 92 239 159 8.2 TABLE CONTINUED ON PG.5 • Pressure rated up to 500 psi/3450 kPa **Center of run to engaged pipe end,female threaded outlet only(dimensions approximate). on steel pipe; also available for use t Available with grooved or female threaded outlet.Specify choice on order. with HDPE pipe t Center of run to end of fitting. • Sizes from 2 x 1/2750 x 15 mm # Female threaded outlets are available to NPT and BSPT specifications. through 8 x 47200 x 100 mm @ See page 7 for Fire Protection approvals and pressure ratings. (a)British Standard female pipe threaded outlet is available as listed.Specify"BSPT"clearly on order. (b)For 76.1 mm threaded outlet,specify 21/2"BSPT clearly on order. §Vds approved for fire protection services a LPCB approved for fire protection services IMPORTANT NOTES: 0 Approved for use in China by Tianjin Approvals Company. Style 920 and Style 920N housings cannot be mated to one another to achieve cross connections. www.victaulic.com iCtaiLJI1C® VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY.©2018 VICTAULIC COMPANY.ALL RIGHTS RESERVED. 11.02_2 REV_0 CARBON STEEL PIPE-HOLE CUT PRODUCTS 11.02 Mechanical-r Bolted Branch Outlets STYLES 920 AND 920N DIMENSIONS size Awl' Dimensions Run x Branch ne Hole Vt Y Z mm no Inches +0.13 Inches Inches Inches Inches InchE s Inches r � TABLE CONTINUED FROM PAGE 4 1 500 1.50 3.88 1 4.56 3.79 9.34 2.75 8.0 165.1 x 25 920N 3450 38.1 99 116 - 96 237 70 3.6 - 1 Y4n 1 500 1.75 4.43 5.13 3.79 9.34 3.25 8.4 32 920N 3450 44.5 113 1 130 96 237 83 3.8 0�� 1 Yz(a)to 500 2.00 4.41 5.13 5.13 3.79 9.34 3.25 8A 5.4 40 920N 3450 50.8 112 130 130 96 237 83 3.8 2.4 GROOVED OUTLET 2(a)t g20N 500 2.50 4.38 5.13 5.13 3.79 9.34 3.88 8.5 6.0 50 3450 63.5 111 130 130 96 237 99 3.9 2.7 76.1 mm 920 500 2.75 4.01 5.13 5.21 3.63 10.51 4.63 8.6 7.6 3450 69.9 110 130 132 92 267 118 3.9 3.4 Y Z 3(a)t 0 920 500 88.9 110 140 130 92 10.51 135 10.2 8.4 1 80 3450 88.9 110 140 130 92 267 135 4.6 3.8 V 4(a)to 920 500 4.50 3.81 5.75 5.38 3.63 10.51 6.25 10.5 8.4 T 100 3450 114.3 97 146 137 92 267 159 4.8 3.8 8 2(a)t 500 2.75 5.44 6.19 6.25 4.81 12.42 4.50 11.6 11.6 w 200 x 50 920 3450 69.9 138 157 159 122 316 114 5.3 5.3 21/2(a)t 920 500 2.75 5.07 6.19 6.19 4.81 12.42 4.50 11.6 11.6 65 3450 69.9 129 157 157 122 316 114 5.3 5.3 FEMALE THREADED OUTLET 76.1 mm n 920 500 2.75 5.25 6.25 4.81 12.42 4.56 11.6 3450 69.9 133 159 122 316 116 5.3 3(a)to Soo 3.50 5.31 6.50 6.50 4.81 12.42 5.31 12.6 11.6 • Provides a direct branch connection at 80 920 3450 88.9 135 165 165 122 316 135 5.7 5.3 any location where a hole can be cut 4(a)tn 92o soo 4so 4.81 6.75 6.38 4.81 12.42 6.25 15.3 zs in the pipe 100 3450 114.3 122 171 162 122 316 159 6.9 5.7 **Center of run to engaged pipe end,female threaded outlet only(dimensions approximate). • A pressure responsive gasket provides t Available with grooved or female threaded outlet.Specify choice on order. the Seal t Center of run to end of fitting. • Request Publication 11.03 for # Female threaded outlets are available to NPT and BSPT specifications. Mechanical-T cross assemblies @ See page 7 for Fire Protection approvals and pressure ratings: • Pressure rated up to 500 psi/3450 kPa (a)British Standard female pipe threaded outlet is available as listed.Specify"BSPT"clearly on order. on steel pipe; also available for use (b)For 76.1 mm threaded outlet,specify 21/2"BSPT clearly on order. with HDPE pipe §Vds approved for fire protection services ❑-PCB approved for fire protection services • Sizes from 2 x 1hY50 x 15 mm 0 Approved for use in China by Tianjin Approvals Company. through 8 x 47200 x 100mm IMPORTANT NOTES: Style 920 and Style 920N housings cannot be mated to each other to achieve cross connections. www.victaulic.com iCtaiLJIiIL'* VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY.©2018 VICTAULIC COMPANY.ALL RIGHTS RESERVED. REV_O 11.02_5 CARBON STEEL PIPE- HOLE CUT PRODUCTS 11.02 Mechanical-TO Bolted Branch Outlets STYLES 920 AND 920N FLOW DATA Flow test data has shown that the total head loss between point(1)and(2)for the Style 920,920N and 929 Mechanical-r fittings can best be expressed in terms of the pressure difference across the inlet and branch.The pressure difference can be obtained from the relationship below. ) Cv and Kv Values Values for flow of water at+60°F/+16°C are shown in the table below. Formulas for CvrK,Values: AP = Q2 Where: AP = Q2 Where: 0 2 Q=Flow(GPM) K 2 Q=Flow(m3/hr) AP=Pressure Drop(psi) AP=Pressure Drop(Bar) Q = C, x AP C =Flow Coefficient Q x AP K =Flow Coefficient = K„ Exaggerated for clarity Equivalent Length of Outlet Size Schedule 40 Carbon Steel Pipe NOMINAL ACTUAL . � O.D. GROOVED '/z 0.840 11 15 21.3 z 9.4 3/4 1.050 16 20 26.7 4 13.7 1 1.315 21 25 33.7 3.. 8 1.8 1'/4 1.660 5'/2 6 50 48 32 42.7 42.9 41.1 1'/z 1.900 53 53 40 48.3 11 11 45.4 45.4 2 2.375 1 112 104 50 60.3 9 10 h 96 89.1 2'/z 2.875 1 119 150 65 73.0 20 12/z 102 128.5 76.1 mm 3.000 16* 161 76.1 138.1 3 3.500 249 237 80 88.9 14 15 213.4 203.1 4 4.500 421 401 100 114.3 20 22 360.8 343.6 t Hazen-Williams coefficient of friction is 120. *Pipe with a wall thickness of 0.165in./4.2mm. 1"Fire Lock-Innovative Groove System(IGS)outlet www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY.©2018 VICTAULIC COMPANY.ALL RIGHTS RESERVED. iCt�iILJI1C® 11.02_9 REV_0 CARBON STEEL PIPE-HOLE CUT PRODUCTS 11.02 Mechanical-r Bolted Branch Outlets STYLES 920 AND 920N FIRE PROTECTION APPROVALS AND PRESSURE RATINGS The information provided below is based on the latest listing and approval data at the time of publication. Listings/Approvals are subject to change and/or additions by the approvals agencies.Contact Victaulic for performance on other pipe and the latest listings and approvals. Approval Agency Run Size Outlet Size Pipe Rated Working Pressures—psi/kPa Actual Nominal Outsi de Vds Size Diameter 21/2-6 2.875-6.625 All 10,40 400 400 400 290 232 1 362 65-150 73.0-168.3 2755 2755 1 2755 1999 1599 2496 21/2-4 2.875-4.500 All DF 300 300 300 290 232 362 65-100 73.0-114.3 2065 2065 2065 1999 1599 2496 21/2-4 2.875-4.500 All SF 300 300 300 290 232 362 65-100 73.0-114.3 2065 2065 2065 1999 1599 2496 6 6.625 3,4 10 300 300 250 290 232 362 150 168.3 2065 2065 1724 1999 1599 2496 6 6.625 3,4 30,40 300 300 300 290 232 362 150 168.3 2065 2065 2065 1999 1599 2496 8 8.625 21/2 10,40 400 _ _ _ 145 200 219.1 2755 1000 8 8.625 3,4 10 300 _ 250 _ 145 200 219.1 2065 1724 1000 8 8.625 3,4 30,40 300 _ 300 _ 145 200 219.1 2065 2065 1000 NOTES: 10 refers to Listed/Approved Schedule 10 steel sprinkler pipe. 40 refers to Listed/Approved Schedule 40 steel sprinkler pipe. DF refers to Listed/Approved Dyna-Flow steel sprinkler pipe manufactured by American Tube Company. SF refers to Listed/Approved Super-Flo steel sprinkler pipe manufactured by Allied Tube and Conduit Corporation. VIC-TAP II HOLE CUTTING TOOL FOR The Vic-Tap II hole cutting tool is designed for use with the Style 931 Vic-Tap II Mechanical-T unit, 4-8"/100-200 MM CARBON STEEL PIPE which is a combination of the Style 920 Mechanical-T and Series 726 Vic-Ball Valve.The Vic-Tap II is capable of tapping into carbon steel pipe systems under pressures up to 500psi/3450kPa. The Style 931 Vic-Tap II Mechanical-T unit is a full port ball valve which can be mounted on 47100mm, 57125mm,67150mm and 87200 mm diameter pipe.The Style 931 comes with a 21h"/65mm grooved outlet. The drill motor is an electric motor with ground fault circuit interrupter(GFCI)in accordance with safety codes. For more information,refer to publication 24.01. www.victaulic.com VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY.©2018 VICTAULIC COMPANY.ALL RIGHTS RESERVED. iCtaILJIiIL'� REV_O 11.02_7 1 s Mechanical-T° bolted Branch Outlets STYLES 920 AND 920N INSTALLATION Reference should always be made to the 1-100 Victaulic Field Installation Handbook for the product you are installing. Handbooks are included with each shipment of Victaulic products for complete installation and assembly data,and are available in PDF format on our website at www.victaulic.com. WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for details. NOTE This product shall be manufactured by Victaulic or to Victaulic specifications.All products to be installed in accordance with current Victaulic installation/assembly instructions.Victaulic reserves the right to change product specifications,designs and standard equipment without notice and without incurring obligations. For complete contact information,visit www.victaulic.com 11.02 1480 REV 0 UPDATED 11/2018 �Ctaill VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY.0 2018 VICTAULIC COMPANY.ALL RIGHTS RESERVED. 11.02_L Victaulic° Firel-ockT" Installation-Ready"" Rigid Couplings ✓ct—au Iiic' Style 009N and Style 109 10.64 Patented Patented 1.0 PRODUCT DESCRIPTION Available Sizes • Style 009N: 11/4— 12"/DN32— DN300 • Style 109: 11/4—2 1/2"/DN32—73.0 mm Pipe Material • Schedule 10, Schedule 40 or specialty carbon steel pipe listed in Section 5. For use with alternative materials and wall thicknesses please contact Victaulic. Maximum Working Pressure • Up to 365 psi/2517 kPa. Function • Joins carbon steel pipe with grooved ends conforming to publication 25.01. • Provides a rigid pipe joint designed to restrict axial or angular movement. 2.0 CERTIFICATION/LISTINGS c @" FM LPCB vdS C E LISTED C104-1a/36 EN 10311 Regulation(EU) No.305/2011 ALWAYS REFER TO ANY NOTIFICATIONS AT THE END OF THIS DOCUMENT REGARDING PRODUCT INSTALLATION,MAINTENANCE OR SUPPORT. System No. Location Spec Section Paragraph Submitted By Date Approved Date victaulic.com 10.64 7072 Rev M Updated 12/2018 ©2018 Victaulic Company.All rights reserved. 1 ictaulic° victaulic.com 3.0 SPECIFICATIONS— MATERIAL Housing: Ductile iron conforming to ASTM A 536, Grade 65-45-12. Ductile iron conforming to ASTM A 395, Grade 65-45-15, is available upon special request. Housing Coating: (specify choice) ❑ Orange enamel (North America, Asia Pacific) ❑ Red enamel (Europe) I-1 Optional for Style 009N: Hot dipped galvanized Gasket: (specify choice) Grade "E" EPDM (Type A) Vic-PIuSTM Pre-lubricated Gasket EPDM (Violet Color Code). Applicable for wet and dry (oil-free air) fire protection systems only. Listed/Approved for continuous use in wet and dry systems. Listed/Approved for dry systems at-40°F/-40°C and above. Not compatible for use with hot water services or steam services. NOTES • Reference should always be made to publication 1-100,Victaulic Field Installation Handbook for gasket lubrication instructions. • Services listed are General Service Guidelines only.It should be noted that there are services for which these gaskets are not compatible.Reference should always be made to publication 05.01,Victaulic Gasket Selection Guide for specific gasket service guidelines and for a listing of services which are not compatible. Bolts/Nuts: (specify choice) Standard: Carbon steel oval neck track bolts meeting the mechanical property requirements of ASTM A449 (imperial) and ISO 898-1 Class 9.8 (M10-M16) Class 8.8(M20 and greater). Carbon steel hex nuts meeting the mechanical property requirements of ASTM A563 Grade B (imperial) and ASTM A563M Class 9 (metric). Track bolts and hex nuts are zinc electroplated per ASTM B633 Fe/Zn 5, finish Type III (imperial) or Type II (metric). ❑ Optional for Style 009N: Stainless steel oval neck track bolts meeting the requirements of ASTM F593, Group 2 (316 stainless steel), condition CW. Stainless steel Heavy Hex nuts meeting the requirements of ASTM F594, Group 2 (316 stainless steel), condition CW, with galling-resistant coating.' Optional bolts/nuts are available in imperial size only. Coupling Linkage: High Strength Steel with comparable physical properties to that of the Track Bolt (ASTM A449). Linkage is zinc electroplated per ASTM B633 Fe/Zn 5, Type III Finish. 10.64 7072 Rev M Updated 12/2018 ©2018 Victaulic Company.All rights reserved. victaulic.com 2 ✓ctaulic° victaulic.com 4.0 DIMENSIONS Style 009N Two-Bolt Installation-Ready Coupling Y Z Y Z X X Style 009N Pre-Assembled Style 009N Joint Assembled Size Bolt/Nut Dimensions Weight Actual Maximum Maximum Allow. Pre-assembled Joint Assembled Outside Working End Pipe End Approx. Nominal Diameter Pressure2 Load2 Separation3 Qty. Size X Y X Y Z (Each) inches inches psi lb inches inches inches inches inches inches inches lb ON mm kPa N mm mm mm mm mm mm mm kg 1 1/4 1.660 365 790 0.10 3/8 x 2 3.13 5.00 2.75 5.00 2.00 1.4 DN32 42A 2517 3514 2.54 2 M10 x 51 79 127 70 127 51 0.6 1 1/2 1.900 365 1035 0.10 3/8 x 2 3.38 5.13 3.00 5.13 2.00 1.5 DN40 48.3 2517 4604 2.54 2 Will x 51 86 130 76 130 51 0.7 2 2.375 365 1617 0.12 3/8 x 21/2 4.00 5.63 3.50 5.63 2.00 1.9 DN50 60.3 2517 7193 3.05 2 M10 x 63 102 143 89 143 51 0.9 21/2 2.875 365 2370 0.12 3/8 x 2'/2 4.50 6.13 4.00 6.13 2.00 2.1 73.0 2517 10542 3.05 2 M 10 x 63 114 156 102 156 51 1.0 3.000 365 2580 0.12 2 3/8 x 21/2 4.63 6.00 4.13 6.13 2.00 2.1 DN65 76.1 2517 11476 3.05 M 10 x 63 118 152 105 156 51 1.0 3 3.500 365 3512 0.12 3/8 x 21/2 5.13 6.75 4.63 6.75 2.00 2.3 DN80 88.9 2517 15622 3.05 2 M10 x 63 130 171 117 171 51 1.0 4 4.500 365 5805 0.17 2 3/9 x 21/2 6.00 7.88 5.63 7.50 2.13 2.9 DN100 114.3 2517 25822 4.32 M10x63 152 200 143 191 54 1.3 4.250 365 5178 0.17 3/8 x 21/2 5.63 7.38 5.38 7.38 2.13 3.1 108.0 2517 23020 4.32 2 M 10 x 63 152 1.87 137 187 54 1.4 5 5.563 365 8872 0.17 2 1/2 x 3 7.25 9.25 6.75 9.13 2.25 5.0 141.3 2517 39456 4.32 M12 x 76 184 235 171 232 57 2.3 5.250 365 7901 0.17 1/2 x 3 6.63 9.00 6.38 9.00 2.25 4.8 133.0 2517 35106 4.32 2 MI x 76 168 229 162 229 57 2.2 5.500 365 8672 0.17 2 1/2 x 3 6.88 9.25 6.75 9.13 2.25 4.9 DN125 139.7 2517 38529 4.32 M12x76 175 235 171 232 57 2.2 6 6.625 365 12582 0.17 '/2 x 31/4 8.38 10.38 7.88 10.13 2.25 6.0 DN150 168.3 2517 44469 4.32 2 M12x83 213 264 200 257 57 2.7 6.250 365 11198 0.17 1/2 x 31/4 7.88 10.00 7.38 9.88 2.25 5.6 159.0 2517 49753 4.32 2 M72 x 83 200 254 187 251 57 2.5 6.500 365 12112 0.17 1/2 x 31/4 8.00 10.25 7.75 10.13 2.25 6.0 165.1 2517 53813 4.32 2 M12 x 83 203 260 197 257 57 2.7 8 8.625 365 21326 0.17 1/8 x 4 10.88 13.38 10.25 13.13 2.50 11.4 DN200 219.1 2517 94863 4.32 2 M16 x 101 276 340 260 333 64 5.2 8.500 365 20712 0.17 5/8 x 4 10.63 13.25 10.25 10.13 2.63 11.4 216.0 2517 55968 4.32 2 M16 x 101 270 337 260 257 67 5.2 10 10.750 300 27229 0.25 7/8 x 61/2 13.75 17.00 13.25 17.13 2.75 22.6 DN250 273.0 2068 121121 6.4 2 M22 x 165 349 432 337 435 70 10.3 12 12.750 300 38303 0.25 7/8 x 61/2 16.00 19.00 15.50 19.13 2.75 27.6 DN300 323.9 2068 170380 6.4 2 M22 x 165 406 483 394 486 70 12.5 2 Working Pressure and End Load are total,from all internal and external loads,based on standard weight(ANSI)steel pipe,standard roll or cut grooved in accordance with Victaulic specifications.See the Listings/Approvals section of this publication for ratings on other pipe. 3 The allowable pipe separation dimension shown is for system layout purposes only.Style 009N couplings are considered rigid connections and will not accommodate expansion or contraction of the piping system. NOTES • When assembling Style 009N or Style 109 couplings onto end caps,take additional care to make certain the end cap is fully seated against the gasket end stop.For Style 009N or Style 109 couplings,use FireLock No.006 end caps containing the"EZ"marking on the inside face or No.60 end caps containing the "QV EZ"marking on the inside face.Non-Victaulic end cap products shall not be used with Style 009N or Style 109 couplings.IMPORTANT:Gaskets intended for the Style 009 or Style 009V couplings cannot be used with the Style 009N or Style 109 coupling.There is no interchanging of gaskets or housings between coupling styles. • Use Of FlushSeal Gaskets For Dry Pipe Systems Style 009N or Style 109 couplings are supplied with Grade"E"Type A gaskets.These gaskets include an integral pipe stop,that once installed provides the similar benefits as a FlushSeal gasket for dry pipe systems.It should be noted that standard Victaulic FlushSeal gaskets cannot be used with the Style 009N or Style 109 couplings. 10.64 7072 Rev M Updated 12/2018 ©2018 Victaulic Company.All rights reserved. victaulic.com 3 ✓ctaulic° victaulic.com 4.1 DIMENSIONS Style 109 One-Bolt Installation-Ready Coupling YB Z YB Z YL YL X X Style 109 Pre-Assembled Style 109 Joint Assembled Size Bolt/Nut Dimensions Weight Actual Maximum Maximum Pipe End Pre-assembled Joint Assembled Outside Working End Separation Approx. Nominal Diameter Pressure4 Load4 Allowable5 Qty.7SizeYL YB X Z YL YB X Z (Each) inches inches psi lb inches inches inches inches inches inches inches inches inches inches lb mm mm kPa N mm mm mm mm mm mm mm mm mm mm kg 1 1/4 1.660 365 790 0.10 3/a x 21/4 1 2.5.88 0 3.13 1.88 1.88 2.63 2.75 1.88 1.4 DN32 42.4 2517 3514 2.54 1 M10 x 57 48 64 79 48 48 67 70 48 0.6 11/2 1.900 365 1035 0.10 3/8 x 21/4 2.00 2.63 3.25 1.88 2.00 2.75 3.00 1.88 1.5 DN40 48.3 2517 4604 2.54 1 M10 x 57 51 67 83 48 51 70 76 48 0.7 2 2.375 365 1616 0.12 3/s x 2 Y2 2.25 2.88 3.88 2.00 2.25 3.13 3.50 2.00 1.8 N5 D0 60.3 2517 7193 3.05 M10 x 6 57 73 98 51 57 79 89 51 0.8 21/2 2.875 365 2370 0.12 1 3/8 x 21/2 2.50 3.13 4.38 1 2.00 2.50 3.38 3.88 2.00 2.1 73.0 2517 10542 3.05 M 10 x 63 64 79 111 51 64 86 98 51 0.9 4 Working Pressure and End Load are total,from all internal and external loads,based on standard weight(ANSI)steel pipe,standard roll or cut grooved in accordance with Victaulic specifications.See the Listings/Approvals section of this publication for ratings on other pipe. 5 The allowable pipe separation dimension shown is for system layout purposes only.Style 109 couplings are considered rigid connections and will not accommodate expansion or contraction of the piping system. NOTES • When assembling Style 009N or Style 109 couplings onto end caps,take additional care to make certain the end cap is fully seated against the gasket end stop.For Style 009N or Style 109 couplings,use FireLock No.006 end caps containing the"EZ"marking on the inside face or No.60 end caps containing the "QV EZ"marking on the inside face.Non-Victaulic end cap products shall not be used with Style 009N or Style 109 couplings.IMPORTANT:Gaskets intended for the Style 009 or Style 009V couplings cannot be used with the Style 009N or Style 109 coupling.There is no interchanging of gaskets or housings between coupling styles. • Use Of FlushSeal Gaskets For Dry Pipe Systems Style 009N or Style 109 couplings are supplied with Grade"E"Type A gaskets.These gaskets include an integral pipe stop,that once installed provides the similar benefits as a FlushSeal gasket for dry pipe systems.It should be noted that standard Victaulic FlushSeal gaskets and cannot be used with the Style 009N or Style 109 couplings. 10.64 7072 Rev M Updated 12/2018 ©2018 Victaulic Company.All rights reserved. victaulic.com 4 ✓ctaulic° victaulic.com 5.0 PERFORMANCE Style 009N Two-Bolt Installation-Ready Coupling Listings/Approvals6 The information provided below is based on the latest listing and approval data at the time of publication. Listings/Approvals are subject to change and/or additions by the approval agencies. Contact Victaulic for performance on other pipe and the latest listings and approvals. Size cULus" FMII VdS LPCB Actual Outside Sch. 10 Sch.40 Sch. 10 Sch.40 Nominal Diameter psi psi psi psi psi psi inches inches kPa kPa kPa kPa kPa kPa DN mm bar bar bar bar bar bar 11/4 1.660 365 365 363 363 363 363 DN32 42.4 2517 2517 2503 2503 2500 2500 25 25 25 25 25 25 11/2 1.900 365 365 363 363 363 363 DN40 48.3 2517 2517 2503 2503 2500 2500 25 25 25 25 25 25 2 2.375 365 365 363 363 363 363 DN50 60.3 2517 2517 2503 2500 2500 2500 25 25 25 25 25 25 2.875 365 365 363 363 363 363 21/2 73.0 2517 2517 2503 2500 2500 2500 25 25 25 25 25 25 3.000 3657 3638 363 363 DN65 76.1 25177 N/A 25038 N/A 2500 2500 257 258 25 25 3 3.500 365 365 363 363 363 363 DN80 88.9 2517 2517 2503 2503 2500 2500 25 25 25 25 25 25 4 4.500 365 365 363 363 363 363 DN100 114.3 2517 2517 2503 2503 2500 2500 25 25 25 25 25 25 4.250 363 363 108.0 N/A N/A 2503 2503 N/A N/A 25 25 5.563 290 365 363 363 232 363 5 2000 2517 2503 2503 1600 2500 141.3 20 25 25 25 16 25 3638 5.250 N/A N/A 25038 N/A N/A N/A 133.0 25 2909 3638 232 363 DN125 5.500 20009 N/A 25038 N/A 1600 2500 139.7 209 258 25 25 300 365 363 363 232 363 6 6.625 2068 2517 2503 2503 1600 2500 DN150 168.3 20 25 257 25 16 25 3638 6.250 N/A N/A 25038 N/A N/A N/A 159.0 25 29010 3638 363 6.500 200010 N/A 25038 N/A N/A 2500 165.1 20 1 1 258 25 6 Listed/Approved for continuous use in wet and dry systems.Listed/Approved for dry systems-40'F/C and above. Please see the Victaulic Installation Manual 1-009N for details concerning when supplemental lubrication is required. 7 cULus listed for DIN 2458(EN 10220)2.6 mm pipe wall. 8 FM approved for BS 1387(EN 10255)Medium 3.6 mm pipe wall. 9 cULus listed for EN 10220 4.0 mm pipe wall. 10 cULus listed for EN 10255 4.5 mm pipe wall. 11 With optional stainless steel fasteners,cULus Listed to 175psi/1207 kPa/12 bar and FM Approved to the FM ratings shown in the above table.The stainless steel fasteners have a marking designation of"316"on the end face of the bolt. 12 cUL listed to 250 psi/1720 kPa/17 bar. 10.64 7072 Rev M Updated 12/2018 ©2018 Victaulic Company.All rights reserved. victaulic.com 5 ✓ctaulic° victaulic.com 5.0 PERFORMANCE (CONTINUED) Style 009N Two-Bolt Installation-Ready Coupling Listings/ApprovalS6 The information provided below is based on the latest listing and approval data at the time of publication. Listings/Approvals are subject to change and/or additions by the approval agencies. Contact Victaulic for performance on other pipe and the latest listings and approvals. Size cULus" FM11 VdS LPCB Actual Outside Sch. 10 Sch.40 Sch. 10 Sch.40 Nominal Diameter psi psi psi psi psi psi inches inches kPa kPa kPa kPa kPa kPa DN mm bar bar bar bar bar bar 8 8.625 300 365 363 363 232 363 DN200 219.1 2068 2517 2503 2503 1600 2500 20 25 25 25 16 25 8.500 290 3638 216.0 2000 N/A 25038 N/A N/A N/A 20 257 10 10.750 300 300 300 300 DN250 273.0 2068 2068 2068 2068 N/A N/A 20 20 20 20 12 30012 300 250 300 12.750 DN300 3.75 206812 2068 1720 2068 N/A N/A 2012 25 17 20 6 Listed/Approved for continuous use in wet and dry systems.Listed/Approved for dry systems-40'F/C and above. Please see the Victaulic Installation Manual 1-009N for details concerning when supplemental lubrication is required. 7 cULus listed for DIN 2458(EN 10220)2.6 mm pipe wall. 8 FM approved for BS 1387(EN 10255)Medium 3.6 mm pipe wall. 9 cULus listed for EN 10220 4.0 mm pipe wall. 10 cULus listed for EN 10255 4.5 mm pipe wall. 11 With optional stainless steel fasteners,cULus Listed to 175psi/1207 kPa/12 bar and FM Approved to the FM ratings shown in the above table.The stainless steel fasteners have a marking designation of"316"on the end face of the bolt. 12 cUL listed to 250 psi/1720 kPa/17 bar. 5.1 PERFORMANCE Style 109 One-Bolt Installation-Ready Coupling Listings/ApprovaIS13 The information provided below is based on the latest listing and approval data at the time of publication. Listings/ Approvals are subject to change and/or additions by the approvals agencies. Contact Victaulic for performance on other pipe and the latest listings and approvals. Size cULus FM Actual Outside Sch. 10 Sch.40 Sch. 10 Sch.40 Nominal Diameter psi psi psi psi inches inches kPa kPa kPa kPa DIN mm bar bar bar bar 11/4 1.660 365 365 365 DN32 42.4 2517 2517 2517 2517 25 25 25 25 1 V2 1.900 365 365 365 365 DN40 48.3 2517 2517 2517 2517 25 25 25 25 2 2.375 365 365 365 365 DN50 60.3 2517 2517 2517 2517 25 25 25 25 2.875 365 365 365 365 21/2 73.0 2517 2517 2517 2517 25 25 25 25 13 Listed/Approved for continuous use in wet and dry systems.Listed/Approved for dry systems-40°F/C and above. Please see the Victaulic Installation Manual 1-109 for details concerning when supplemental lubrication is required. 10.64 7072 Rev M Updated 12/2018 ©2018 Victaulic Company.All rights reserved. victaulic.com 6 ✓ctaulic° victaulic.com 5.2 PERFORMANCE Specialty Pipe Style 009N Two-Bolt Installation-Ready Coupling Listings/Approvals Size Pressure Rating cULus FM psi psi inches kPa kPa Pipe Type DIN bar bar 11/4-4 300 EF DN32—DN100 2068 N/A 20 300 300 EL 11/4 2 2068 2068 DN32—DN50 20 20 300 ET40 1 1/4-2 2068 N/A DN32—DN50 20 300 EZF 3-4 DN80—DN100 2068 N/A 20 300 300 EZT 1 1/4-2 2068 2068 DN32—DN50 20 20 300 11/2-4 FF DN40—DN100 2068 N/A 20 300 300 1 1/4-2 2068 2068 DN32—DN50 20 20 300 300 1 1/4-4 2068 2068 DN32—DN 100 20 20 MF 175 175 6 1205 1205 DN150 12 12 300 1 Y4-2 MT DN32—DN50 2068 20 300 MILT 1 1/4—2 N/A 2068 DN32—DN50 20 300 21/2—4 TF 73.0 mm—DIN100 N/A 2068 20 175 300 WG5,WG5E,WF5,WG7,WG7E,WL7 1 /4—4 1205 2068 DN32—DN100 12 20 300 300 WLS 1 1/4-2 2068 2068 DN32—DN50 20 20 NOTES • EF=EDDY FLOW steel pipe manufactured by Bull Moose Tube Co. • MT=Mega-Thread steel pipe manufactured by Wheatland Tube Co. • EL=EDDYLITE steel pipe manufactured by Bull Moose Tube Co. • MILT=MLT steel pipe manufactured by Wheatland Tube Co • ET40=Eddythread 40 steel pipe manufactured by Bull Moose Tube Co. • TF=Tex-Flow steel pipe manufactured by Tex-Tube Co. • EZF=EZ-Flow steel pipe manufactured by Northwest Pipe Co. • WG5,WG5E,WF5=WGalweld 5,WGalweld 5E,WFlow 5 steel pipe • EZT=EZ-Thread steel pipe manufactured by Youngstown Tube Co. manufactured by Wuppermann Stahl GmbH. • FF=Fire-Flo steel pipe manufactured by Youngstown Tube Co. • WG7,WG7E,WL7=WGalweld 7,Wgalweld 7E,WLight 7 steel pipe • GL=GL steel pipe manufactured by Wheatland Tube Co. manufactured by Wuppermann Stahl GmbH • MF=Mega-Flow steel pipe manufactured by Wheatland Tube Co. • WLS=WLS steel pipe manufactured by Wheatland Tube Co. 10.64 7072 Rev M Updated 12/2018 ©2018 Victaulic Company.All rights reserved. victaulic.com 7 ✓ctaulic° victaulic.com 5.3 PERFORMANCE Specialty Pipe Style 109 One-Bolt Installation-Ready Coupling Listings/Approvals Size Pressure Rating cULus FM inches psi psi kPa kPa Pipe Type DN bar bar 11/a 21/2 AM- 300 DN32—73.0 mm N/A 2068 EF 20 1 1/2—21/z 300 DN40—73.0 mm 2068 N/A 20 1 1/a-2 300 Easy-Flow DN32—DN50 N/A 2068 20 1 1/a-2 300 EL DN32—DN50 N/A 20668 20 1 1/4-2 300 300 ET40 DN32—DN50 2068 2068 20 20 11/a-2 300 DN32—DN50 N/A 2068 EZT 20 1 1/z—2 300 2068 N/A DN40—DN50 20 11/2 21/z 300 300 FF DN40—73.0 mm 2068 2268 11/a-2 300 GL DN32—DN50 N/A 2068 300 300 1 1/a—21/z IMF DN32—73.0 mm 20668 20668 20 20 11/a 2 300 300 MT DN32—DN50 2068 2068 20 20 11/a 2 300 300 MLT DN32—DN50 2068 2068 20 20 300 TF 73.0 1/mm N/A 2068 20 11/a-2 300 WG7,WG7E DN32—DN50 N/A 2068 20 11/a-2 300 WLS DN32—DN50 N/A 2068 020 NOTES • GL=GL steel pipe manufactured by Wheatland Tube Co. • EF=EDDY FLOW steel pipe manufactured by Bull Moose Tube Co. . MF=Mega-Flow steel pipe manufactured by Wheatland Tube Co. • Easy-Flow=Easy-Flow steel pipe manufactured by Borusan . MT=Mega-Thread steel pipe manufactured by Wheatland Tube Co. Mannesmann Boru. . MLT=MLT steel pipe manufactured by Wheatland Tube Co. • EL=EDDYLITE steel pipe manufactured by Bull Moose Tube Co. . TF=Tex-Flow steel pipe manufactured by Tex-Tube Co. • ET40=Eddythread 40 steel pipe manufactured by Bull Moose Tube Co. . WG7,WG7E=WGalweld 7 and WGalweld 7E steel pipe manufactured by • EZT=EZ-Thread steel pipe manufactured by Youngstown Tube Co. Wuppermann Stahl GmbH. • FF=Fire-Flo steel pipe manufactured by Youngstown Tube Co. • WLS=WLS steel pipe manufactured by Wheatland Tube Co. 10.64 7072 Rev M Updated 12/2018 ©2018 Victaulic Company.All rights reserved. victaulic.com 8 ✓ctaulic° victaulic.com 6.0 NOTIFICATIONS 09AWARNING � _ Read and understand all instructions before attempting to install any Victaulic products. • Always verify that the piping system has been completely depressurized and drained immediately prior to installation,removal,adjustment,or maintenance of any Victaulic products. • Wear safety glasses, hardhat,and foot protection. Failure to follow these instructions could result in death or serious personal injury and property damage. • These products shall be used only in fire protection systems that are designed and installed in accordance with current,applicable National Fire Protection Association(NFPA 13, 13D, 13R,etc.)standards,or equivalent standards,and in accordance with applicable building and fire codes.These standards and codes contain important information regarding protection of systems from freezing temperatures,corrosion, mechanical damage,etc. • The installer shall understand the use of this product and why it was specified for the particular application. • The installer shall understand common industry safety standards and potential consequences of improper product installation. • It is the system designer's responsibility to verify suitability of materials for use with the intended fluid media within the piping system and external environment. • The material specifier shall evaluate the effect of chemical composition, pH level,operating temperature,chloride level,oxygen level, and flow rate on materials to confirm system life will be acceptable for the intended service. Failure to follow installation requirements and local and national codes and standards could compromise system integrity or cause system failure, resulting in death or serious personal injury and property damage. 7.0 REFERENCE MATERIALS 05.01:Seal Selection Guide 25.01:Original Groove System(OGS)Groove Specifications 1-009N:Installation Instructions FireLock EZTm Rigid Coupling Style 009N 1-100:Victaulic Field Installation Handbook 1-109:Installation Instructions FireLockTm One-Bolt Rigid Coupling Style 109 I-ENDCAP:Victaulic End Caps Installation Instructions User Responsibility for Product Selection and Suitability Note Each user bears final responsibility for making a determination as to the suitability of This product shall be manufactured by Victaulic or to Victaulic specifications.All products Victaulic products for a particular end-use application,in accordance with industry to be installed in accordance with current Victaulic installation/assembly instructions. standards and project specifications,and the applicable building codes and related Victaulic reserves the right to change product specifications,designs and standard regulations as well as Victaulic performance,maintenance,safety,and warning equipment without notice and without incurring obligations. instructions.Nothing in this or any other document,nor any verbal recommendation, Installation advice,or opinion from any Victaulic employee,shall be deemed to alter,vary,supersede, Reference should always be made to the Victaulic installation handbook or installation or waive any provision of Victaulic Company's standard conditions of sale,installation instructions of the product you are installing.Handbooks are included with each shipment guide,or this disclaimer. of Victaulic products,providing complete installation and assembly data,and are available Intellectual Property Rights in PDF format on our website at www.victaulic.com. No statement contained herein concerning a possible or suggested use of any material, Warranty product,service,or design is intended,or should be constructed,to grant any license Refer to the Warranty section of the current Price List or contact Victaulic for details. under any patent or other intellectual property right of Victaulic or any of its subsidiaries or affiliates covering such use or design,or as a recommendation for the use of such Trademarks material,product,service,or design in the infringement of any patent or other intellectual Victaulic and all other Victaulic marks are the trademarks or registered trademarks of property right.The terms"Patented"or"Patent Pending'refer to design or utility patents Victaulic Company,and/or its affiliated entities,in the U.S.and/or other countries. or patent applications for articles and/or methods of use in the United States and/or other countries. 10.64 7072 Rev M Updated 12/2018 ©2018 Victaulic Company.All rights reserved. victaulic.com 9 ✓ctaulic` Victaulic° Flexible Coupling ✓ctauliic° Style 75 06.05 1-8YDN25-DN200 Exaggerated for clarity 1.0 PRODUCT DESCRIPTION Available Sizes • 1 —87DN25— DN200 Pipe Material • Carbon steel • Stainless steel Maximum Working Pressure • Accommodates pressures ranging from full vacuum (29.9 in Hg/760 mm Hg) up to 500 psi/3447 kPa/34 bar • Working pressure dependent on material, wall thickness and size of pipe Application • Joins standard roll grooved and cut grooved pipe, as well as grooved fittings, valves and accessories • Provides a flexible pipe joint which allows for expansion, contraction and deflection • Up to 50% lighter in weight than standard Victaulic Style 77 or Style 177N flexible couplings 2.0 CERTIFICATION/LISTINGS e@- <&> VdS LPCB USM NOTES • Download publication 10.01 for Fire Protection Certifications/Listings Reference Guide. • See publication 02.06:Victaulic Potable Water Approvals ANSI/NSF for potable water approvals if applicable. ALWAYS REFER TO ANY NOTIFICATIONS AT THE END OF THIS DOCUMENT REGARDING PRODUCT INSTALLATION,MAINTENANCE OR SUPPORT. System No. Location Spec Section Paragraph Submitted By Date Approved Date victaulic.com 06.05 1470 Rev P Updated 10/2017 ©2017 Victaulic Company.All rights reserved. 1 iictauliic° victaulic.com 3.0 SPECIFICATIONS— MATERIAL Housing: Ductile iron conforming to ASTM A536, Grade 65-45-12. Ductile iron conforming to ASTM A395, Grade 65-45-15, is available upon special request. Housing Coating: (specify choice) ❑ Standard: Orange enamel ❑ Optional: Hot dipped galvanized ❑ Optional: Contact Victaulic with your requirements for other coatings. Gasket: (specify choice') ❑ Grade "E" EPDM EPDM (Green stripe color code). Temperature range—30OF to+230°F/-340C to+110°C. May be specified for hot water service within the specified temperature range plus a variety of dilute acids, oil-free air and many chemical services. UL Classified in accordance with ANSI/NSF 61 for cold +73°F/+23°C and hot+180°F/+82°C potable water service and ANSI/NSF 372. NOT COMPATIBLE FOR USE WITH PETROLEUM SERVICES OR STEAM SERVICES. ❑ Grade "T" Nitrile Nitrile (Orange stripe color code). Temperature range—20OF to+180°F/-290C to+82°C. May be specified for petroleum products, air with oil vapors, vegetable and mineral oils within the specified temperature range; not compatible for hot dry air over+140°F/+600C and water over+150°F/+660C. NOT COMPATIBLE FOR USE WITH HOT WATER. ❑ Others For alternate gasket selection, reference publication 05.01: Victaulic Seal Selection Guide- Elastomeric Seal Construction. Services listed are General Service Guidelines only.It should be noted that there are services for which these gaskets are not compatible.Reference should always be made to the latest Victaulic Seal Selection Guide for specific gasket service guidelines and for a listing of services which are not compatible. Bolts/Nuts: (specify choice2) ❑ Standard: Carbon steel oval neck track bolts meeting the mechanical property requirements of ASTM A449 (imperial) and ISO 898-1 Class 9.8 (metric). Carbon steel hex nuts meeting the mechanical property requirements of ASTM A563 Grade B (imperial - heavy hex nuts) and ASTM A563M Class 9 (metric - hex nuts). Track bolts and hex nuts are zinc electroplated per ASTM B633 ZN/FE5,finish Type III (imperial)or Type II (metric). ❑ Optional (imperial): Stainless steel oval neck track bolts meeting the mechanical property requirements of ASTM F593, Group 2 (316 stainless steel), condition CW. Stainless steel heavy nuts meeting the mechanical property requirements of ASTM F594, Group 2 (316 stainless steel), condition CW, with galling reducing coating. 2 Optional bolts/nuts are available in imperial sizes only. 06.05 1470 Rev P Updated 10/2017 ©2017 Victaulic Company.All rights reserved. victaulic.com 2 ✓ctaul�c° victaulic.com 4.0 DIMENSIONS Style 75 --Y� X Pipe End Deflection from Size Separation3 Centerline3 Bolt/Nut Dimensions Weight Actual Outside Approx. Nominal Diameter Allowable Per Cplg. Pipe Qty. Size X Y Z (Each) inches inches inches inches/ft. imperial inches inches inches lb DN mm mm Degrees mm/m metric mm mm mm kg 1 1.315 0-0.06 0.57 3/8 x 2 2.38 4.27 1.77 1.3 DN25 33.7 0-1.6 2°-43' 48 2 M10 x 51 61 108 45 0.6 1 1/4 1.660 0-0.06 0.45 3/8 x 2 2.68 4.61 1.77 1.4 DN32 42.4 0-1.6 2°-10' 38 2 M10 x 51 68 117 45 0.6 1 1/2 1.900 0-0.06 10-56' 0.40 1/8 x 2 2.91 4.82 1.77 1.5 DN40 48.3 0-1.6 33 2 M10 x 51 74 122 45 0.6 2 2.375 0-0.06 1 -31 0 ' 0.32 3/8 x 2 3.43 5.22 1.88 1.7 DN50 60.3 0-1.6 26 2 M10x51 87 133 48 0.8 21/2 2.875 0-0.06 10-15' 0.26 2 3/8 x 2 3.88 5.68 1.88 1.9 73.0 0-1.6 22 M10 x 51 98 144 48 0.9 3.000 0-0.06 10 12 0.26 3/8 x 2 4.00 5.90 1.88 1.9 DN65 76.1 0-1.6 22 2 M10 x 51 102 150 48 0.9 3 3.500 0-0.06 0.22 1/2 x 2 3/4 4.50 7.00 1.88 2.9 DN80 88.9 0-1.6 1-2' 18 2 M12 x 70 114 178 48 1.3 31/2 4.000 0-0.06 0.19 1/2 x 2 3/4 5.00 7.50 1.88 2.9 DN90 101.6 0-1.6 0°54 16 21 M12 x 70 127 191 1 48 1.3 4 4.500 0-0.13 0- 0.34 1/2 x 2 3/4 5.80 8.03 2.13 4.1 DN100 114.3 0-3.2 1 36' 28 2 M12 x 70 147 204 54 1.9 4.250 0-0.13 0.35 1/2 x 2 3/4 5.55 7.79 2.13 3.7 108.0 0-3.2 1 -41 29 2 M 12 x 70 141 198 54 1.7 5.000 0-0.13 1-26 0.25 %x 31/4 6.13 9.43 2.13 5.5 127.0 0-3.2 21 2 M16x83 156 240 54 2.5 5 5.563 0-0.13 10-18 0.27 %x 31/4 6.88 10.07 2.13 5.8 141.3 0-3.2 23 2 M16x83 175 256 54 2.6 5.250 0-0.13 10-21' 0.28 2 5/s x 31/4 6.55 9.37 2.13 6.0 133.0 0-3.2 24 M16x83 166 238 54 2.7 5.500 0-0.13 10-18' 0.28 2 5/s x 3 1/4 6.80 9.59 2.13 6.3 DN125 139.7 0-3.2 24 M16x83 173 244 54 2.9 6.000 0-0.13 1 12' 0.21 2 1/8 x 31/4 7.38 10.48 1.88 6.2 152.4 0-3.2 18 M16x83 187 266 48 2.8 6 6.625 0-0.13 10 5, 0.23 2 1/8 x 3 1/4 8.00 11.07 2.13 7.0 DN150 168.3 0-3.2 18 M16x83 203 281 54 3.2 6.250 0-0.13 10 9, 0.24 2 1/8 x 3 1/4 7.63 10.49 2.13 6.8 159.0 0-3.2 20 M16x83 194 266 54 3.1 6.500 0-0.13 17 0 0.23 5/s x 3 1/4 7.84 10.66 2.08 6.6 165.1 0-3.2 58 2 M16x83 199 271 53 3.0 8.515 0-0.13 0 0.18 3/4 x 41/4 10.19 13.75 2.32 13.2 216.3 0-3.2 0-51' 46 2 M20 x 108 259 350 59 6.0 8 8.625 0-0.13 0 0.18 3/4 x 41/4 10.34 13.97 2.13 12.4 DN200 219.1 0-3.2 0-50' 14 2 M20 x 108 263 355 59 5.6 3 Allowable Pipe End Separation and Deflection figures show the maximum nominal range of movement available at each joint for standard roll grooved pipe. Figures for standard cut grooved pipe may be doubled.These figures are maximums;for design and installation purposes these figures should be reduced by: 50%for 3/4-3 1h"/DN20-DN90;25%for 4"/DN100 and larger. NOTE • Metric thread size bolts are available(color coded gold)for all coupling sizes upon request.Contact Victaulic for details. 06.05 1470 Rev P Updated 10/2017 ©2017 Victaulic Company.All rights reserved. victaulic.com 3 ✓ctaul�c° victaulic.com 5.0 PERFORMANCE Style 75 Size Actual Maximum Outside Working Maximum Nominal Diameter Pressure4 End Load4 inches inches psi lb DN mm kPa N 1 1.315 500 680 DN25 33.7 3447 3,025 1 1/4 1.660 500 1080 DN32 42.4 3447 4,805 1 1/2 1.900 500 1420 DN40 48.3 3447 6,320 2 2.375 500 2215 DN50 60.3 3447 9,860 21/2 2.875 500 3245 73.0 3447 14,440 3.000 500 3535 DN65 76.1 3447 15,730 3 3.500 500 4800 DN80 88.9 3447 21,360 31/2 4.000 500 6300 DN90 101.6 3447 28,035 4 4.500 500 7950 DN 100 114.3 3447 35,380 4.250 450 6380 108.0 3103 28,395 5.000 450 8820 127.0 3103 39,250 5 5.563 450 10935 141.3 3103 48,660 5.250 450 9735 133.0 3103 43,325 5.500 450 10665 DN 125 139.7 3103 47,460 6.000 450 12735 152.4 3103 56,670 6 6.625 450 15525 DN 150 168.3 3103 69,085 6.250 450 13800 159.0 3103 61,405 6.500 450 14930 165.1 3103 66,412 8.515 450 25625 216.3 3103 113,98 8 8.625 450 26280 DN200 219.1 3103 116,945 4 Working Pressure and End Load are total,from all internal and external loads,based on ANSI B36.10 sized carbon steel pipe,grooved in accordance with Victaulic specifications.Contact Victaulic for performance on other pipe. NOTE • WARNING:FOR ONE TIME FIELD TEST ONLY,the Maximum Joint Working Pressure may be increased to 11h times the figures shown. 06.05 1470 Rev P Updated 10/2017 ©2017 Victaulic Company.All rights reserved. victaulic.com 4 ✓ctaul�c° victaulic.com 6.0 NOTIFICATIONS EL&MWARNIA • Victaulic RX roll sets must be used when grooving light-wall/thin-wall stainless steel pipe for use with Victaulic Couplings. Failure to use Victaulic RX roll sets when grooving light-wall/thin-wall stainless steel pipe may cause joint failure, resulting in serious personal injury and/or property damage. NOTICE • Victaulic RX grooving rolls must be ordered separately. They are identified by a silver color and the designation RX on the front of the roll sets. 7.0 REFERENCE MATERIALS 02.06:Victaulic@ Potable Water Approvals ANSI/NSF 05.01:Victaulic@ Seal Selection Guide-Elastomeric Seal Construction 06.15:Victaulic@ Pressure Ratings and End Loads for Victaulic Couplings on Steel Pipe 10.01:Victaulic@ Products for Fire Protection Pinings Systems-Regulatory Aooroval Reference Guide 17.01:Victaulic@ Pipe Preparation for Use on Stainless Steel Pipe With Victaulic Products 17.09:Victaulic@ Ductile Iron Grooved Couplings Performance Data for Stainless Steel Pipe 25.01:Victaulic@ Standard Groove Specifications 26.01:Victaulic@ Design Data 29.01:Victaulic@ Terms and Conditions of Sale 1-100:Victaulic@ Field Installation Handbook User Responsibility for Product Selection and Suitability Note Each user bears final responsibility for making a determination as to the suitability of This product shall be manufactured by Victaulic or to Victaulic specifications.All products Victaulic products for a particular end-use application,in accordance with industry to be installed in accordance with current Victaulic installation/assembly instructions. standards and project specifications,and the applicable building codes and related Victaulic reserves the right to change product specifications,designs and standard regulations as well as Victaulic performance,maintenance,safety,and warning equipment without notice and without incurring obligations. instructions.Nothing in this or any other document,nor any verbal recommendation, Installation advice,or opinion from any Victaulic employee,shall be deemed to alter,vary,supersede, Reference should always be made to the Victaulic installation handbook or installation or waive any provision of Victaulic Company's standard conditions of sale,installation instructions of the product you are installing.Handbooks are included with each shipment guide,or this disclaimer. of Victaulic products,providing complete installation and assembly data,and are available Intellectual Property Rights in PDF format on our website at www.victaulic.com. No statement contained herein concerning a possible or suggested use of any material, Warranty product,service,or design is intended,or should be constructed,to grant any license Refer to the Warranty section of the current Price List or contact Victaulic for details. under any patent or other intellectual property right of Victaulic or any of its subsidiaries or affiliates covering such use or design,or as a recommendation for the use of such Trademarks material,product,service,or design in the infringement of any patent or other intellectual Victaulic and all other Victaulic marks are the trademarks or registered trademarks of property right.The terms"Patented"or"Patent Pending'refer to design or utility patents Victaulic Company,and/or its affiliated entities,in the U.S.and/or other countries. or patent applications for articles and/or methods of use in the United States and/or other countries. 06.05 1470 Rev P Updated 10/2017 ©2017 Victaulic Company.All rights reserved. victaulic.com 5 ✓ctaulrc° pppppp� VASC k*4* p Engineered Solutions This packet contains engineering and product information specific to the following project: PROJECT INFORMATION Project: Ductile Iron Fittings Project Address: Architect: Engineer: Contractor: Submittal Date: March 29,2023 APPROVER INSTRUCTIONS Optional Stainless Steel Bolts&Nuts Review product specifications: Stainless steel bolts and nuts also available.Contact Please review the product specifications and technical information for each an ASC Engineered Solutions representative for more product to ensure suitability of application and use. information. Review product options: Housing If applicable,please review the selected product options on each product Ductile Iron conforming to ASTM A536,Grade 65-45-12 or page to ensure suitability of application and use. Malleable Iron conforming to ASTM A47,Grade 32510. Approve or reject individual products: Options Please complete the approval stamp sectionfor each product. ❑ Rust inhibiting lead-free paint Color:Orange(standard) ❑ Hot Dipped Zinc Galvanized(optional) ❑ Other Colors Available(IE:RAL3000 and RAL9000 For other coating requirements contact a ASC Engineered Solutions representative APPROVAL STAMP ❑Approved ❑Approved as noted ❑Not approved Remarks: PRODUCT INDEX The following products are included in this submittal 3201 90' Elbow 3205 Straight Tee 3221 R Reducing Coupling 3388 Cored Plug 3224 Cap 3221 Coupling 3283 Bushing page 1 ASC-SUB-Package-Cover-v0120210101 SPF Ductile Iron Threaded Fittings CP, ASC `111111�:p Engineered Solutions Fig. 3201900 Elbow Material Specifications Dimensions:ASME B16.3 Material:ASTM A536 Grade 65-45-12 Finish:Black Threads:NPT per ASME 131.20.1 Agency Approvals:All ductile iron threaded fittings are UL/ULC Listed and FM Approved. c �L us Fn� Note:Ductile iron fittings have higher tensile strength than LISTED APPROVED that of steel pipe.Therefore,over tightening can cause For Listings/Approval Details and Limitations,visit damage to pipe threads which may cause Leakage.Ductile ourwebsite at www.asc-es.com or contact an ASC iron fittings should be tightened approximately three turns Engineered Solutions"Sales Representative. beyond hand tight,but no more than four turns. Figure 3201 90°Elbow Nominal Size Maximum DimensionA Approx Wt.Each A Working Pressure A L i in.(mm) psi(kPa) in.(mm) Lbs.(kg) 1 500 1.50 0.62 20 3450 38.10 0.68 --------- ----- - i 11/4 500 1.75 0.90 32 3450 44.45 0.41 A 11/2 500 1.94 1.20 40 3450 49.276 0.54 2 500 2.25 1.85 50 3450 57.15 0.84 A-Working Pressure Ratings are for reference only and based on Sch.40 pipe.For the latest UL/ULC,and FM pressure ratings versus pipe schedule,please visit asc-es.com or contact your local ASC Engineering Solutions'"Representative. So, An ASC Engineered Solution PROJECT INFORMATION APPROVAL STAMP Project: Ductile Iron Fittings ❑Approved Address: ❑Approved as noted Contractor: ❑Not approved Engineer: Remarks: Submittal Date: March 29, 2023 Notes 1: Notes 2: SPF/MI-1.15 page 1 PS—SUB-3201—v0120220118 SPF Ductile r / Engineered Solutions Straight Tee Fig. 3205 Material Specifications Dimensions:ASME B16.3 Material:ASTM A536 Grade 65-45-12 4 Finish:Black / Threads:NPT per ASME 61.20.1 Agency Approvals:All ductile iron threaded fittings are UL/ULC Listed and FM Approved. Note:Ductile iron fittings have higher tensile strength than that of steel pipe.Therefore,over tightening can cause damage to pipe threads which may cause leakage.Ductile c ul us FM iron fittings should be tightened approximately three turns LLsrEo APPROVED beyond hand tight,but no more than four turns. For Listings/Approval Details and Limitations,visit our website at www.asc-es.com or contact an ASC Engineered Solutions"Sales Representative. Figure 3205 Straight Tee Nominalsize Maximum Dimension Approx Wt.Each Working Pressure A In.(mm) psi(kPa) In.(mm) Lbs.(kg) 1 500 1.50 0.85 25 3450 38.10 0.39 A 11/4 500 1.75 1.22 - ------- ----- - 32 3450 44.45 0.55 11/2 500 1.94 1.55 I 40 3450 49.27 0.70 A :—A 2 500 2.25 2.45 50 3450 57.15 1.11 A-Working Pressure Ratings are for reference only and based on Sch.40 pipe.For the latest UL/ULC,and FM pressure ratings versus pipe schedule,please visit asc-es.com or contact your local ASC Engineering Solutiomlm Representative. So, An ASC Engineered Solution PROJECT INFORMATION APPROVAL STAMP Project: Ductile Iron Fittings ❑Approved Address: ❑Approved as noted Contractor: ❑Not approved Engineer: Remarks: Submittal Date: March 29, 2023 Notes 1: Notes 2: SPF/MI-1.15 page 1 PS-SUB-3205-v0120220118 SPF Ductile Iron Threaded Fittings CP, ASC kkp Engineered Solutions Reducing Coupling Fig. 3221 R Material Specifications Dimensions:ASME B16.3 Material:ASTM A536 Grade 65-45-12 Finish:Black Threads:NPT per ASME B1.20.1 Agency Approvals:All ductile iron threaded c 4L us FM fittings are UL/ULC Listed and FM Approved. LRTED APPROVED Note:Ductile iron fittings have higher tensile strength than For Listings/Approval Details and Limitations,visit that of steelpipe.e Therefore,overti tightening can cause ourwebsiteat www.a sc-es.comor contact anAScpp g g Engineered sowtlons"sales Representative. damage to pipe threads which may cause Leakage.Ductile iron fittings should be tightened approximately three turns beyond hand tight,but no more than four turns. Figure 3221R Reducing Coupling Nominal Size Maximum DimensionA Approx Wt.Each Working Pressure A in.(mm) psi(kPa) in.(mm) Lbs.(kg) 1 x'/2 500 1.69 0.39 JJ A 25 x 15 3450 42.92 0.18 1 x 3/4 500 1.69 0.53 25 x 20 3450 42.92 0.24 11/4 x 3/4 500 2.06 0.64 32 x 20 3450 52.32 0.29 A-Working Pressure Ratings are for reference only and based on Sch.40 pipe.Forthe latest UL/ULC,and FM pressure ratings versus pipe schedule,please visit asc-es.com or contact your localASC Engineering Solutions'""Representative. scl� An ASC Engineered Solution PROJECT INFORMATION APPROVAL STAMP Project: Ductile Iron Fittings ❑Approved Address: ❑Approved as noted Contractor: ❑Not approved Engineer: Remarks: Submittal Date: March 29, 2023 Notes 1: Notes 2: SPF/MI-1.15 page 1 PS—SUB-3221R—v0120220118 SPF Ductile Iron Threaded Fittings CP, ASC kkp Engineered Solutions Cored Plug Fig. 3388 Material Specifications Dimensions:ASME B16.14 Material:ASTM A536 Grade 65-45-12 Finish:Black Threads:NPT per ASME 131.20.1 Agency Approvals:All ductile iron threaded fittings are UL/ULC Listed and FM Approved. ♦Pressure-Temperature Ratings in accordance with ASME B16.3 Class 150 Note:Ductile iron fittings have highertensile strength than usTO APPROVED that of steel pipe.Therefore,overtightening can cause For Listings/Approval Details and Limitations,visit damage to pipe threads which may cause Leakage.Ductile our website at www.asc-es.com or contact an ASC iron fittings should be tightened approximately three turns Engineered Solutions'Sales Representative. beyond hand tight,but no more than four turns. Figure 3388 Cored Plug Nominal Size Maximum Dimension A Approx. Working Pressure A Wt.Each in.(mm) psi(kPa) in.(mm) Lbs.(kg) 1/2* 500 0.94 0.10 15 3450 23.87 0.05 3/4 500 1.07 0.17 A20 3450 27.17 0.08 I 1 500 1.25 0.28 25 3450 31.75 0.13 — 11/4 500 1.36 0.44 32 3450 34.54 0.20 11/2 500 1.45 0.62 40 3450 36.83 0.28 2 500 1.56 0.91 50 3450 39.62 0.41 A-Working Pressure Ratings are for reference only and based on Sch.40 pipe.For the latest UL/ULC,and FM pressure ratings versus pipe schedule,please visit asc-es.com or contact your Local ASC Engineering Solutions'"^Representative. `Part supplied as Solid Plug. IS scl� An ASC Engineered Solution PROJECT INFORMATION APPROVAL STAMP Project: Ductile Iron Fittings ❑Approved Address: ❑Approved as noted Contractor: ❑Not approved Engineer: Remarks: Submittal Date: March 29, 2023 Notes 1: Notes 2: SPF/MI-1.15 page 1 PS—SUB-3388—vo120220124 SPF Ductile Iron Threaded Fittings / Engineered Solutions Cap Fig. 3224 Material Specifications Dimensior ASME B16.3 Materi, ASTM A536 Grade 65-45-12 Finish:Black Threads:NPT per ASME 131.20.1 Agency Approvals:All ductile iron threaded c 4� us FM fittings are UL/ULC Listed and FM Approved. LISTED APPROVED Note:Ductile iron fittings have higher tensile strength than For Listings/Approval Details and Limitations,visit that of steel pipe.Therefore,over tightening can cause our website at wwwasc-es.com or contact an ASC Engineered solutions"Sales Representative. damage to pipe threads which may cause leakage.Ductile iron fittings should be tightened approximately three turns beyond hand tight,but no more than four turns. Figure 3224 Cap Nominalsize Maximum Dimension Approx Wt.Each Working Pressure In.(mm) psi(kPa) In.(mm) Lbs.(kg) 1 500 1.16 0.32 25 3450 29.46 0.15 A 11/4 500 1.28 0.43 32 3450 32.51 0.20 11/2 500 1.33 0.60 40 3450 33.78 0.27 2 500 1.45 0.91 50 3450 36.83 0.41 A-Working Pressure Ratings are for reference only and based on Sch.40 pipe.For the Latest UL/ULC,and FM pressure ratings versus pipe schedule,please visit asc-es.com or contact your local ASC Engineering Solutions'"'Representative. So, An ASC Engineered Solution PROJECT INFORMATION APPROVAL STAMP Project: Ductile Iron Fittings ❑Approved Address: ❑Approved as noted Contractor: ❑Not approved Engineer: Remarks: Submittal Date: March 29, 2023 Notes 1: Notes 2: SPF/MI-1.15 page 1 PS-SUB-3224-v0120220118 SPF Ductile Iron Threaded Fittings 2 AS C / Engineered Solutions Coupling Fig. 3221 Material Specifications Dimensior, ASME B16.3 Material:ASTM A536 Grade 65-45-12 Finish:Black Threads:NPT perASME 61.20.1 Agency Approvals:All ductile iron threaded fittings are UL/ULC Listed and FM Approved. Note:Ductile iron fittings have higher tensile strength than that of steel pipe.Therefore,over tightening can cause c ul us FM damage to pipe threads which may cause leakage.Ductile VLV APPROVED iron fittings should be tightened approximately three turns LISTED beyond hand tight,but no more than four turns. For Listings/Approval Details and Limitations,visit ourwebsiteatw w.asc-es.com or contact an ASC "Wo Engineered Solutions"Sales Representative. Figure 322 Coupling Nominal5ize Maximum DimensionA Approx Wt.Each E Working Pressure A A In.(mm) psi(kPa) In.(mm) Lbs.(kg) 1 500 1.67 0.40 i 25 3450 42.42 0.18 i i 11/4 500 1.93 0.57 ---i-- 32 3450 49.02 0.26 i 11/2 500 2.15 0.75 i 40 3450 54.61 0.34 i 2 500 2.53 1.15 50 3450 64.26 0.52 A-Working Pressure Ratings are for reference only and based on Sch.40 pipe.Forthe latest UL/ULC,and FM pressure ratings versus pipe schedule,please visit asc-es.com or contact your local ASC Engineering Solutions'"'Representative. So, An ASC Engineered Solution PROJECT INFORMATION APPROVAL STAMP Project: Ductile Iron Fittings ❑Approved Address: ❑Approved as noted Contractor: ❑Not approved Engineer: Remarks: Submittal Date: March 29, 2023 Notes 1: Notes 2: SPF/MI-1.15 page 1 PS-SUB-3221-v0120220118 SPF Ductile Iron Threaded Fittings / Engineered Solutions Bushings Fig. 3283 Material Specifications Dimenslor ASME B16.14 F Materi7' ASTM A536 Grade 65-45-12 Finish:Black Threads:NPT per ASME 61.20.1 Agency Approvals:All ductile iron threaded fittings are UL/ULC Listed and FM Approved. c �L us Fm Note:Ductile iron fittings have higher tensile strength than LISTED APPROVED that of steel pipe.Therefore,over tightening can cause For Listings/Approval Details and Limitations,visit damage to pipe threads which may cause leakage.Ductile our website at www.asc-es.com or contact an ASC iron fittings should be tightened approximately three turns Engineered Solutions'Sales Representative. beyond hand tight,but no more than four turns. Figure 3283 Bushings Nominal size Maximum Dimensions Male(M)x Working Style Ap Eachprox F i + B Female(F) Pressure A A B c in.(mm) psi(kPa) in.(mm) in.(mm) in.(mm) - Lbs.(kg) A 1 x 1/2 500 0.75 0.25 1.42 Outside 0.22 M- 25 x 15 3450 19.05 6.35 36.06 0.10 1 x 3i4 Soo 0.75 0.25 1.42 0.17 Inside Head 25 x 20 3450 19.05 6.35 36.06 Outside 0.08 11/4 x 1 500 0.80 0.28 1.76 Outside 0.28 32 x 25 3450 20.32 7.11 44.70 0.13 11/2 x 1 500 0.83 0.31 2.00 0.45 Outside F C � B 40 x 25 3450 21.08 7.874 50.80 0.20 � 11/2 x 11/4 500 0.83 0.31 2.00 0.30 Outside 40 x 32 3450 21.08 7.874 50.80 0.14 A 2 x 1 500 0.88 0.41 1.95 Inside 0.67 50 x 25 3450 22.35 10.414 49.43 0.30 M- 2x11/4 500 0.88 0.34 2.48 Outside 0.73 Outside Head 50 x 32 3450 22.35 8.636 62.99 0.33 2 x 11/2 500 0.88 0.34 2.48 0.61 50 x 40 3450 22.35 8.636 62.99 Outside 0.28 ♦-Working Pressure Ratings are for reference only and based on Sch.40 pipe.Forthe latest UL/ULC,and FM pressure ratings versus pipe schedule,please visit asc-es.com or contact your local ASC Engineering Solutiom'"Representative. So, An ASC Engineered Solution PROJECT INFORMATION APPROVAL STAMP Project: Ductile Iron Fittings ❑Approved Address: ❑Approved as noted Contractor: ❑Not approved Engineer: Remarks: Submittal Date: March 29, 2023 Notes 1: Notes 2: SPF/MI-1.15 page 1 PS-SUB-3283-v0120220118 Threaded Accessories B3205 -Threaded Rod (right-hand threads - both ends) B3205L-Threaded Rod (right& left hand threads) Size Range: 3/8"-16 thru 7/8"-9 rod TL Material: Steel Specify Length Function: Recommended for use as a hanger support in hanger assemblies. L Rod is threaded on both ends with right hand threads of the length shown.Also available with left and right hand threads-specify Fig. B3205L when ordering. TL Maximum Temperature: 750°F(399°C) A Finish: Plain or Electro-Galvanized. Contact customer service for alternative Thread Size finishes and materials. Order By: Figure number, rod size, length and finish 0000 Standard Design Load Thread Size Thread Length TL 650°F(343°C) 750°F(399°C) Part No. A in. (mm) Lbs. (M) Lbs. (M) B3205-3/8 x V 3/8"-16 21/2" (63.5) 730 (3.25) 572 (2.54) B3205-1/2 x V 1/2"-13 21/2" (63.5) 1350 (6.00) 1057 (4.70) B3205-5/8xV 5/8"-11 21/2" (63.5) 2160 (9.61) 1692 (7.52) B3205-3/4 x V 3/4'-10 3" (76.2) 3230 114.37) 2530 (11.25) B3205-7/8 X V 7/8"-9 31/2" (88.9) 4480 (19.93) 3508 (15.60) For larger sizes consult full line pipe hanger catalog. ATR - All Threaded Rod - 120" (3.05m) Lengths OPM TOLCOT'" Fig. 99 - All Threaded Rod Cut To Length Size Range: 1/4"-20 thru 7/8"-9 rod in 120" lengths or cut to length Material: Steel Maximum Temperature: 750°F(399°C) Finish: Plain or Electro-Galvanized. Contact customer service for alternative finishes and materials. Approvals: Included in our Seismic Engineering Guidelines approved by the State of California Office of Statewide Health Planning and Development(OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to our Seismic Engineering Guidelines, OPM-0052-13. Order By: Figure number, rod size, length and finish - Part No.-Size x Length Threads Recommended Load Approx.Wt./100 Ft. ATR Fig.99 Per Inch Lbs. (M) Lbs. (kg) ATR 1/4"x 120 99-1/4"x length 20 240 (1.07) 12 (5.44) ATR 3/8"x 120 99-3/8"x length 16 730 (3.24) 29 (13.15) ATR 1/2"x 120 99-1/2"x length 13 1350 (6.00) 53 (24.04) ATR 5/8"x 120 99-5/8"x length 11 2160 (9.60) 89 (40.37) ATR 3/4"x 120 99-3/4"x length 10 3230 (14.37) 123 (55.79) ATR 7/8"x 120 99-7/8"x length 9 4480 (19.93) 170 (77.11) For larger sizes consult full line pipe hanger catalog. All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwise specified. Eaton 96 B-Line series Fire Protection Solutions Pipe Hangers Fig. 200 - "Trimline" Adjustable Band Hanger (B-Line Fig. B3170NF) QTOLCO Fig. 20OF "TFiMllineff Admustable Band Hanger with Felt Lining. (B Line Fig. B317ONFF) c @us Fig. 200C "TFiMllineff Admustable Band Hanger with Plastie Coated (B Line Fig. B317ONFC) LISTED Fig. 200S "TFiMllineff Adjustable Band Hanger with Non Captured Nut. FM Size Range: a�Eo Fig. 200 - 1/2" (15mm)thru 8" (200mm) pipe Material: Steel, Pre-Galvanized to G90 specifications Function: For fire sprinkler and other general piping purposes. Knurled -- swivel nut design permits hanger adjustment after installation. Features: • (1/2" (15mm)thru 2" (50mm)) Flared edges ease installation for all pipe types and protect CPVC plastic pipe from abrasion. Captured design keeps adjusting nut from separating with hanger. Hanger is easily B f installed around pipe. For hanger with non-captured nut order Fig. 200S. t • (21/2" (65mm)thru 8" (200mm)) Spring tension on nut holds it securely in hanger before installation.Adjusting nut is easily removed. Approvals: Underwriters Laboratories listed (1/2" (15mm)thru 8" (200mm)) in the USA(UL)and Canada (cUL)for steel and CPVC plastic pipe and Fig.200-1/2.200 3/4 Factory Mutual Engineering Approved(FM) (3/4" (20mm)thru 8" (200mm)). Fig.200-1 to 200-2 Fig.200-21/2to 200-8 Conforms to Federal Specifications WW-H-171 E&A-A-1192A, Type 10 and Manufacturers Standardization Society ANSI/MSS SP-69&SP-58, _ Type 10. Maximum Temperature: 650OF(343'C) Finish: Pre-Galvanized. Stainless Steel materials will be supplied with (2) hex nuts in place of a knurl nut. Order By: Figure number and pipe size Designed to meet or exceed requirements of o, FM DS 2-0. Fig.200 a Fig.200C Fig.200E Pipe Size Rod Size A B Approx.Wt./100 \ ti Part No. in. (mm) in. (mm) in. (mm) Ibs. (kg) 200-1/2 1/2" (15) 3/8"-16 31/8" (79.4) 25/8" (66.7) 11 (5.0) 200-3/4 3/4" (20) 3/8"-16 31/8" (79.4) 21/2" (63.5) 11 (5.0) 200-1 1" (25) 3/8"-16 33/8" (85.7) 25/8" (66.7) 12 (5.5) 200-11/4 11/4" (32) 3/8"-16 33/4" (94.0) 27/8" (73.0) 13 (5.9) 200-11/2 11/2" (40) 3/8"-16 37/8" (98.4) 27/8" (73.0) 14 (6.4) 200-2 2" (50) 3/8"-16 41/2" (114.3) 3" (76.3) 15 (6.9) 200-21/2 21/2" (65) 3/8"-16 55/8" (142.9) 41/8" (104.7) 27 (12.3) 200-3 3" (75) 3/8"-16 57/8" (149.1) 4" (101.6) 29 (13.3) Fig.200S 200-31/2 31/2" (90) 3/8"-16 73/8" (187.3) 51/4" (133.3) 34 (15.6) 200-4 4" (100) 3/8-16 73/8" (187.3) 5" (127.0) 35 (16.0) 200-5 5" (125) 1/2"-13 91/8" (231.8) 61/4" (158.7) 66 (30.2) 200-6 6" (150) 1/2"-13 101/8" (257.2) 63/4" (171.4) 73 (33.4) 200-8 8" (200) 1/2"-13 131/8" (333.4) 83/4" (222.2) 136 (62.3) All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwise specified. B-Line Fire Protection Solutions 21 by EJ-N Seismic Bracing Fig. 980 -TOLCO Universal swivel sway brace attachment-3/8r"-16 to 3/4"40 rods Fig. 980H -TOLCO Universal swivel sway brace attachment-1/8'-9 to 11/4"-7 Size Range: One size fits bracing pipe 1" (25mm)thru 2" (50mm), B-Line series OPM C@US 12 gauge(2.6mm)channel. LISTED Material: Carbon steel Function: Multi-functional attachment to structure or braced pipe fitting. Features: This product's design incorporates a concentric attachment opening which is critical to the performance of structural seismic connections and in accordance with 980 NFPA 13, 2019 Section 18.5.11.5. The Fig. 980 mounts to any surface angle and the D break off bolt head assures verification of proper installation. Installation: Fig.980 is the structural or transitional attachment component of a longitudinal or lateral sway brace assembly. It is intended to be combined with the B "bracing pipe" and TOLCO'"" "braced pipe" attachment, Fig. 1001, 2002, 3000, 4L or A approved attachment to pipe to form a complete bracing assembly. NFPA 13 guidelines Set Bolt Mounting Hardware should be followed. Included Is Not Included To Install: Place the Fig. 980 onto the "bracing pipe".Tighten the set bolt until the head breaks off. Attachment can pivot for adjustment to proper brace angle. 061, Approvals:—Underwriters Laboratories Listed in the USA(UL)and Canada (cUL). UL Listed for the following brace member type pipes: Sch. 40, KSD 3562.Ask the factory for additional information as it may vary by product size. Included in our Seismic Engineering Guidelines approved by the State of California Office of Statewide Health Planning and Development(OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to our Seismic Engineering Guidelines, OPM-0052-13. For FM Approval information refer to FM Approved page 61. Note: Fig. 980 Swivel Attachment and Fig. 1001, 2002, 3000, 4L, or approved attachment to pipe make up a sway brace system of UL Listed attachments and bracing materials which satisfies the requirements of Underwriters Laboratories and the National Fire Protection Association (NFPA) Finish: Plain, Electro-Galvanized or Stainless Steel. Contact customer service for alternative finishes. Order By: Figure number and finish. r, Fig. .9Il0 Pat. #6,273,372, Pat. #6,517,030, Pat. #6,953,174, 11 Pat. #6,708,930, Pat. #7,191,987, Pat. #7,441,730, Pat. #7,669,806 Brace A B D** Max.Design Approx.Wt./100 Fig.4B shown Catalog# in. (mm) in. (mm) in. (mm) Load(cULus) Ibs. (kg) Ibs./(kN) *980-3/8 7/16 (11.1) 1600(7.12) 149 (67.6) La: *980-'/2 91/16 (14.3) 2100(9.34) 148 (67.1) *980-5/s 49/1s (114.9) 21/1s (52.4) 11/16 (17.5) 2100(9.34) 147 (66.7) Fig.1001 �\ *980-3/4 13/16 (20.6) 2100(9.34) 146 (66.2) Fig.M 980H 7/s 15/16 (23.8) Fig.980H 402 (182.3) ` 980H-1 11/16 (27.0) is not 400 (181.4) \ 980H-11/a 63/4 (171.4) 31/2 (88.9) 13/16 (30.2) UL Listed 397 (180.1) + Brace or FM 980H-1'/4 15/16 (33.3) Approved 390 (176.9) Lateral Brace *Sizes available in stainless steel(980S Vo,980S 1/2,980S s/a,and 980S 1/4)and have the same UL rating as what is listed. **Mounting attachment hole size. Eaton's B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components, resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are combined with products not provided by Eaton. All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwise specified. Eaton 60 B-Line series Fire Protection Solutions Seismic Bracing Fig. 980-TOLCO Universal swivel sway brace attachment-3/8"-16 to 3/4'-10 rods Fig. 980H -TOLCO Universal swivel sway brace attachment-1/8'-9 to 11/4"-7 Size Range: One size fits bracing pipe 1" (25mm)thru 2" (5omm), B-Line series O 12 gauge (2.6mm) channel. FM Material: Carbon steel OPM APPROVED Function: Multi-functional attachment to structure or braced pipe fitting. Features: This product's design incorporates a concentric attachment opening which is critical to the performance of structural seismic connections and in accordance with NFPA 13, 2019 Section 18.5.11.5.The Fig. 980 mounts to 980 any surface angle and the break off bolt head assures verification of proper ' installation. D Installation: Fig.980 is the structural or transitional attachment component of a J 9� longitudinal or lateral sway brace assembly. It is intended to be combined with B the "bracing pipe" and TOLCO'" "braced pipe" attachment, Fig. 1000, 1001, A 3000,4L, or other TOLCO approved attachment to pipe to form a complete bracing assembly. NFPA 13 guidelines should be followed. set Bolt Mounting Hardware To Install: Place the Fig. 980 onto the "bracing pipe".Tighten the set bolt until Included Is Not Included the head breaks off. Attachment can pivot for adjustment to proper brace angle. Approvals:—Approved by Factory Mutual Engineering(FM). Included in our Seismic Engineering Guidelines approved by the State of California Office of Statewide Health Planning and Development(OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to `. our Seismic Engineering Guidelines, OPM-0052-13. For UL Listed information refer to UL Listed page 60. Note: Fig. 980 Swivel Attachment and Fig. 1000, 1001, 4L or other TOLCO —A't approved attachment to pipe that make up a sway brace system of bracing materials which satisfies the requirements of Factory Mutual Engineering and the National Fire Protection Association (NFPA) Finish: Plain, Electro-Ga Ivan ized or Stainless Steel. Fig.980 Contact customer service for alternative finishes. ; Order By: Figure number and finish. Fig 1001 Pat. #6,273,372, Pat. #6,517,030, Pat. #6,953,174,Pat. #6,708,930, Pat. #7,191,987, Pat. #7,441,730, Fig.980/ l Pat. #7,669,806 ` Designed to meet or exceed requirements of FM DS 2-8. Fig.4L Brace #" Longitudinal Lateral Brace Brace A B D** Max. Design Load*** (FM) Approx.W000 Catalog# in. (mm) in. (mm) in. (mm) 30°-44° 45°-59° 60°-74° 75°-90* Ibs. (kg) Ibs./(kN) Ibs./(kN) Ibs./(kN) IbsJ(kN) 980-3/8 7/16 (11.1) 149 (67.6) 980-'/2 9/,s (14.3) 2370 2790 3360 3750 148 (67.1) 98U 5/6 49/16 (114.9) 2'/16 (52.4) 11/16 (17.5) (10.54) (12.41) (14.94) (16.68) 147 (66.7) 980 3/4 13/16 (20.6) 146 (66.2) 980H 7/8 15/16 (23.8) 402 (182.3) 980H-1 11/16 (27.0) 400 (181.4) 63/4 (171.4) 31/2 (88.9) Fig.980H is not UL Listed 980H-1'/8 13/16 (30.2) or FM Approved 397 (180.1) 980H-1'/4 15/16 (33.3) 390 (176.9) **Mounting attachment hole size. ***Installed with 1"or 11/4"schedule 40 brace pipe. Eaton's B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components, resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton,except that, in addition to the other exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are combined with products not provided by Eaton. All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwise specified. B-Line series Fire Protection Solutions 61 Eaton C - - - Fig. 4A - Pipe Clamp for Sway Bracing Component of State of California OSHPD Approved C Seismic Restraints System us Size Range — 4"thru 8" pipe. For sizes smaller than 4" use TOLCOO Fig. 4. LIST® Material — Carbon Steel B Function — For bracing pipe against sway and seismic disturbance. Approvals — Underwriters' Laboratories Listed in the USA(UL)and Canada(cUL) ..- 4"thru 8". Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development(OSHPD). Installation Instructions — The Fig.4A is the"braced pipe"attachment component of a longitudinal, lateral or riser brace assembly. It is intended to I A be combined with the"bracing pipe"and TOLCO transitional and structural attachment component(s)to form a complete bracing assembly. NFPA 13 and/or f OSHPD guidelines should be followed. / To Install — Place the Fig.4A over the pipe to be braced.Attach TOLCO D transitional fitting, either Fig.980, 910 or 909,to the clamp ears.Tighten bolts and nuts;torque requirement is a minimum of 50 ft. lbs.Transitional fitting attachment can pivot for adjustment to proper brace angle. Finish — Plain Note — Available in Electro-Galvanized and HDG finish or Stainless Steel materials. C Order By — Figure number, pipe size and finish 0 I Fig.4A- Longitudinal Brace ° Fig.4A- Lateral Brace Cooper B-Line,Inc.'s("Cooper B-Line")seismic bracing components are designed to be compatible only with other Cooper B-Line bracing components, resulting in a listed seismic bracing assembly.Cooper B-Line's warranty for seismic bracing components will be the warranty provided in Cooper B-Line's standard terms and conditions of sale made available by Cooper B-Line,except that,in addition to the other exclusions from Cooper B-Line's warranty, Cooper B-Line makes no warranty relating to Cooper B-Line's seismic bracing components that are combined with products not provided by Cooper B-Line. Dimensions•Weights Pipe Max.Horizontal Approx. Sizes A B C D Bolt Size Design Load Wt./100 4 8 Yz 9/6 3 3/8 3 T116 1/2 1600 221 5 9 3/4 9/16 3 7/8 4 3/8 'h 1600 253 6 11 1/2 5/8 5 5 1/8 'h 2015 513 8 13'/4 3/4 6'1/1e 61/8 1/2 2015 601 COOPER B-LINE 1375 Sampson Ave•Corona,CA 92879•800.786.5266•FAX:951.737.0330 www.tolco.com -.A �J —Am—a0v COOPER B-Line Seismic Bracing TOLCO Fig. 1001 - sway brace attachment (UL listed) Size Range: Pipe size to be braced: 1"(25mm)thru 8"(200mm) IPS. Pipe size used for bracing: 1" (25mm)and 1'/4' (32mm) Schedule 40 IPS. OPM C UL US Material: Steel LISTED Function: For bracing pipe against sway and seismic disturbance.The pipe attachment component of a sway brace system: Fig. 1001 is used in conjunction with a Fig. 900 Series fitting and joined together with bracing pipe per NFPA 13, forming a complete sway brace assembly. Features: Can be used to brace schedule 7 through schedule 40 IPS. Field adjustable, making critical pre-engineering of bracing pipe length unnecessary. Unique design requires no threading of bracing pipe. Comes assembled and ready for installation. Fig. 1001 has built-in visual verification of correct installation. See installation note below. 0 Installation Note: Position Fig. 1001 over the pipe to be braced and tighten two hex head cone point set bolts until heads bottom out.A minimum of 1" (25mm) pipe extension is recommended. Brace pipe can be installed on top or bottom of pipe to be braced. Approvals: Underwriters Laboratories Listed in the USA(UL)and Canada (cUL). UL Listed Set Bolts for the following sprinkler type pipes: Sch.40 (and as brace member), Sch. 10, Bull Moose Included Eddy Flow,Wheatland Mega Flow, DIN 2448, KSD 3562 (and as brace member), KSD 3507.Ask the factory for additional information as it may vary by product size. Included in our Seismic Engineering Guidelines approved by the State of California Office of Statewide Health Planning and Development(OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to our Seismic Engineering Guidelines, OPM-0052-13. For FM Approval information refer to FM Approved page 67. Finish: Plain, Electro-Galvanized or Hot Dip Galvanized. Contact customer service for alternative finishes and materials. ti Order By: Order by figure number, pipe size to be braced, followed by pipe size used for bracing (1" (25mm)or 1'/4°(32mm)), and finish. i Pipe Part Number&Approx.Wt./100 Design Load-Lbs. Size 1"(25mm)Brace Pipe 11/4"(32mm)Brace Pipe For Brace Pipe Size 1"/11/4-' Sch.7 Sch.10 Sch.40 in. (MM) Lbs. (kg) Lbs. (kg) 1"/1'/4" 1"/1'/4" 1"/1'/4" 1" (25) 1001-1 X1 104.6 (47.4) 1001-1 X 1'/4 122.2 (55.4) -/- -/- 1000/1000 11/4" (32) 1001-11/4 X 1 105.2 (47.7) 1001-1'/4 X 11/4 122.6 (55.6) 1000/1000 1000/1000 1000/1000 1'/2" (40) 1001-11/2 X 1 107.0 (48.5) 1001-1'/2 X 11/4 124.7 (56.6) 1500/1500 1500/1500 1500/1500 2" (50) 1001-2 X 1 112.6 (51.1) 1001-2 X 11/4 129.2 (58.6) 1500/1500 1500/1500 1500/1500 *21/2"(65) 1001-21/2 X 1* 136.3 (61.8) 1001-21/2 X 11/4* 154.4 (70.0) 2000/2000 2000/2000 2000/2000 3" (80) 1001-3 X 1 145.0 (65.8) 1001-3 X 11/4 163.1 (74.0) 2000/2000 2000/2000 2000/2000 4" (100) 1001-4 X 1 158.6 (71.9) 1001-4 X 11/4 176.7 (80.1) 2000/2000 2000/2000 2000/2000 5" (100) 1001-5 X 1 173.2 (78.6) 1001-5 X 1'/4 191.4 (86.8) -/- 2000/2000 2000/2000 *6" (150) 1001-6 X 1* 190.0 (85.2) 1001-6 X 11/4* 206.0 (93.4) 2000/2000 2000/2000 2000/2000 *8" (200) 1001-8 X 1* 217.4(111.5) 1001-8 X 11/4* 265.3(120.3) -/- 2000/2000 2000/2000 *Note: Metric sizes available for 65mm, 150mm, 200mm pipe size with 25mm and 32mm brace pipe size. Contact the factory. 0 O Fig.1001 All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwise specified. Eaton 66 B-Line series Fire Protection Solutions Seismic Bracing TOLCO Fig. 1001 - sway brace attachment (FM approved) Size Range: Pipe size to be braced: 1"(25mm)thru 8" (200mm) IPS. Pipe size used QpM FM for bracing: 1"(25mm)and 11/4"(32mm) Schedule 40 IPS. APPROVED Material: Steel Function: For bracing pipe against sway and seismic disturbance.The pipe attachment component of a sway brace system: Fig. 1001 is used in conjunction with a Fig. 900 Series fitting and joined together with bracing pipe per NFPA 13, forming a complete sway brace assembly. Features: Can be used to brace schedule 7 through schedule 40 IPS. Field adjustable, making critical pre-engineering of bracing pipe length unnecessary. Unique design requires no threading of bracing pipe. Can be used as a component of a four-way riser brace. Comes assembled and ready for installation. Fig. 1001 has built-in visual verification of correct installation. See installation note below. Installation Note: Position Fig. 1001 over the pipe to be braced and tighten two hex head cone point set bolts until heads bottom out.A minimum of 1" (25mm) pipe extension is recommended. Brace pipe can be installed on top or bottom of set Bolts pipe to be braced. Included Approvals: Approved by Factory Mutual Engineering (FM). Included in our / Seismic Engineering Guidelines approved by the State of California Office of Statewide Health Planning and Development(OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to our Seismic Engineering Guidelines, OPM-0052-13. For LIL Listed information refer to LIL Listed page 66. Finish: Plain, Electro-Galvanized or Hot Dip Galvanized. Contact customer service for alternative finishes and materials. Order By: Order by figure number, pipe size to be braced,followed by pipe size used for bracing (1"(25mm)or 1'/4"(32mm)) , and finish. Important Note: Fig. 1001 is precision manufactured to perform its function as a critical component of a complete bracing assembly.To ensure performance, the FM Approval requires that Fig. 1001 must be used only with other TOLCO'" bracing products.The Fig. 1001 is not intended for use with the Fig.907 4-way Longitudinal Brace Attachment. Designed to meet or exceed requirements of FM DS 2-8. Design Load-For Sch.7,Sch.10,&Sch.40 Pipe Pipe Part Number&Approx.Wt./100 Allowable Horizontal Capacity(Ibf)Per Installation'23 Size 1"(25mm)Brace Pipe 11/4"(32mm)Brace Pipe 30°-44° 45°-59° 60°-74° 75°-90° in. (mm) Lbs. (kg) Lbs. (kg) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) 1" (25) 1001-1 X 1 104.6 (47.4) 1001-1 X 11/4 122.2 (55.4) 1800 (8.01) 2550 (11.34) 3120 (13.88) 3490 (15.52) 11/4"(32) 1001-11/4 X 1 105.2 (47.7) 1001-1'/4 X 11/4 122.6 (55.6) 1230 (5.47) 1740 (7.74) 2140 (9.52) 2380 (10.59) 11/2"(40) 1001-11/2 X 1 107.0 (48.5) 1001-1'/2 X 11/4 124.7 (56.6) 1230 (5.47) 1740 (7.74) 2140 (9.52) 2380 (10.59) 2" (50) 1001-2 X 1 112.6 151.1) 1001-2 X 11/4 129.2 (58.6) 1230 (5.47) 1740 (7.74) 2140 (9.52) 2380 (10.59) *21/2"(65) 1001-21/2 X 1* 136.3 (61.8) 1001-21/2 X 11/4* 154.4 (70.0) 800 (3.56) 1130 (5.03) 1380 (6.14) 1540 (6.85) 3" (80) 1001 3 X 1 145.0 (65.8) 1001 3 X 11/4 163.1 (74.0) 850 (3.78) 1200 (5.34) 1470 (6.54) 1640 (7.30) 4" (100) 1001-4 X 1 158.6 (71.9) 1001-4 X 11/4 176.7 (80.1) 850 (3.78) 1200 (5.34) 1470 (6.54) 1640 (7.30) 5" (100) 1001-5 X 1 173.2 (78.6) 1001-5 X 11/4 191.4 (86.8) 510 (2.27) 730 (3.25) 890 (3.96) 990 (4.40) *6"(150) 1001-6 X 1* 190.0 (85.2) 1001-6 X 11/4* 206.0 (93.4) 510 (2.27) 730 (3.25) 890 (3.96) 990 (4.40) *8"(200) 1001-8 X 1* 217.4 (111.5) 1001-8 X 11/4* 265.3 (120.3) 510 (2.27) 730 (3.25) 890 (3.96) 990 (4.40) FM Approved when used with 1 or 11/4 inch NPS Schedule 40 Gl3 T 3091,EN 10255H,or JIS G3451 steel pipe as the brace member. 3 Load rating for LW above refers to FM Approved Lightwall Pipe commonly referred to as"Schedule 7".These ratings may also be applied when EN 10220 and GB/T 8163 steel pipe. Load rating for Schedule 10 above may be applied to GB/T 3092,EN 10255M and H,or JIS G3454,FM Approved Thinwall,or Schedule 40 steel pipes. Note: See UL load ratings in UL Listed Design Load chart shown under drawing. *Note: Metric sizes available for 65mm, 150mm,200mm o X pipe size with 25mm and 32mm brace pipe size. Contact the factory. i Fig.1001 All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwise specified. B-Line series Fire Protection Solutions 67 Eaton Seismic Structural Attachments TOLCO Fig. 828- universal sway brace attachment to steel c&US < FM > OPM Size Range: One size accommodates all Fig. 900 Series sway brace attachments. LISTED APPROVED Fits from 3/8" (9.4mm)to'/a° (22.2mm)thick steel structure. For thicknesses less than a/a" (9.4mm) refer to Fig. 825 and Fig. 825A. Material: Steel Function: To attach sway brace assemblies and/or hanger assemblies to structural steel members. ® 1 Set Screws Features: Permits secure non-friction connection without drilling or welding. Unique and design allows offset placement on wide flange beam, C-channel, open web,welded steel �® i='Attachment g p g p I Bolt and Nut trusses, etc. Secures brace to structure either across or along the beam. Break-off set Included bolts allow for visual verification of proper installation torque. Approvals: Underwriters Laboratories Listed in the USA and Canada (cULus). Factory Mutual Approved (FM). Included in our Seismic Engineering Guidelines approved by the State of California Office of Statewide Health Planning and Development(OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please Flange Maximum thickness LIL Rated load refer to our Seismic Engineering Guidelines, OPM-0052-13. .375"—.499" 1090 lbs.(4.84kN) Installation: The Fig. 828 is the structural attachment component of a longitudinal or .500"—.875" 1370lbs.(6.09kN) lateral sway brace assembly. It is intended to be combined with a TOLCO transitional attachment, "bracing pipe" and a TOLCO "braced pipe" attachment to form a complete bracing assembly. NFPA 13, FM IDS 2-8, and/or OSPHD guidelines should be followed. To Install: Slide the Fig. 828 on the flange of the beam, truss, or girder. Be sure the attachment is fully engaged to the rear of the opening.Tighten the cone point set screws until the heads break off. Remove the flange nut from the carriage bolt. Install a TOLCO swivel fitting (Fig, 909, 910, 980, *986). Use flange nut to secure the swivel fitting. *Not UL listed when used in combination with Fig. 986 Finish: Plain or Electro-Galvanized Weight: Approx.Wt./100-341 lbs. (154.7kg) Order By: Figure number and finish Patent Pending Note: Retaining strap not required. FM Approved Allowable Horizontal Load With Brace Perpendicular To Beam Brace Angle(degrees from vertical) Beam,truss or girder 30°-441 45°-59° 60°-741 75°-90° Fig.828 980 2220 3340 4040 Fig.828 (4.35OkN) (9.780kN) (14.8501<N) (17.970kN) — li May pivot FM Approved Allowable Horizontal Load in any With Brace Parallel To Beam direction Brace Angle(degrees from vertical) 30°-44° 45°-59° 60°-74° 75°-90° 820 1270 1490 1650 (3.64OkN) (5.640kN) (6.620kN) (7.33OkN) FM Approved design loads are based on ASD design method. Eaton's B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components, resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are combined with products not provided by Eaton. All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwise specified. updated 4-&21 Eaton 16 B-Line series Seismic Bracing Products www.phd-ft- DOMESTIC BEAM CLAMP FIG. 350, 353, 354, 355, 356, & 357 Function: Designed for attaching hanger rod to the top flange of a beam or bar D- joist,where the flange thickness does not exceed 3/4"(19.05mm). The open U design permits rod adjustment. The universal design of the 3/8" 1 Fig. 353 allows it to be used in an inverted position on the bottom Iv flange of a beam as well. 3 Material: Malleable iron with hardened steel cup point set screw and locknut Finish: Plain or electro-galvanized(Hot dipped galvanized with electro- (19.05) galvanized hardware upon request) A Approvals: Underwriters' Laboratories Listed in the U.S. (UL), Canada(CUL), for sizes 3/8"to 7/$"only. Factory Mutual Approved for rod sizes 3/8"and E 1/2"only. Complies with Federal Specifications A-A-1192A(Type 19) c©Us 0 B and Manufacturers' Standardization Society ANSI/MSS SPSP-58 USTED APPROVED (Type 19)which supersedes ANSI/MSS SP-69. Fig. 353 sized for 3/8"rod can be used in an inverted position(bottom of beam) and follows the same U.S. (UL), Canada(CUL), and Factory Mutual Approvals. Used in this manner the 3/8"Fig. 353 also complies with Federal Specifications A-A-1192A(Type 23) and Manufacturers' Standardization Society ANSI/MSS SPSP-58 (Type 23)which supersedes ANSI/MSS SP- 69. (Approvals are only valid for beam clamps with locknut). Ordering: Specify figure number,rod size,material, and finish. Set screw Torque Nominal % 1/2 Caution should be NOTE: When a torque wrench is unavailable, the setscrew should be tightened Thread Size taken not to over so it contacts the I-beam and then an additional'/4 to turn. Rec. in-lbs. 60 125 tighten the set screw Torque N-m (6.8) 04.1) Figure Rod M LoadeC Wt.Each Numbers Size A B C D E Max.Pipe Size lbs. kN lbs. kg *350 1/4 7/8 (22.23) 11/2 (38.10) 15/8 (41.28) 1/2 (12.70) N/A N/A 250 (1.11) .34 (.15) A 353 3/8 7/8 (22.23) 11/2 (38.10) 15/8 (41.28) 1/2 (12.70) 4 (100) 400 (1.78) .33 (.15) 354 1/2 1 (25.40) 11/2 (38.10) 111/16 (42.86) 1/2 (12.70) 8 (200) 500 (2.22) .34 (.15) 355 5/8 11/16 (26.99) 11/2 (38.10) 17/8 (47.63) 518 (15.88) 8 (200) 600 (2.67) .39 (.18) 356 3/4 15/16 (33.34) 13/4 (44.45) 2% (60.33) 5/E (15.88) 8 (200) 800 (3.56) .63 (.29) 357 7/8 15/16 (33.34) 13/4 (44.45) 2% (60.33) 5/8 (15.88) 8 (200) 1200 (5.34) .60 (.27) " 1/4"Fig.350 Not UL or FM approved. n 3/8"Fig. 353 Reversible design approved for bottom beam use. Unless otherwise specified, all dimensions on drawings and in charts are in inches and dimensions shown in parentheses are in millimeters. BFAM CLAMPS --plul�nfg com FIG. 358 RETROFIT RETAINING STRAP Function: Designed for use with Fig. 345,Fig. 350, and Fig. 360 to offer C more secure fastening of beam clamps to beam where seismic protection is provided. Material: Carbon steel(Type 304 or 316 Stainless Steel upon request) Finish: Pre-galvanized Approvals: Underwriters' Laboratories Listed in the U.S. (UL) and Canada (CUL)for 3/8" and t/Z" rod sizes only. Meets NFPA13 cus requirements for hangers and fasteners subject to earthquakes. UsTED Ordering: Specify figure number, length,rod size, and material. NOTE: Use jam nut over hanger rod to secure retaining strap. 2 inches (50.8) should be added to beam flange width to determine length. Wt.Each Rod Size Length C 4112(114.3) 6(152.4) 8(203.2) 10(254.0) 12(304.8) 14(355.6) 318 .06 (.027) .08 (.036) .11 (.050) .14 (.064) .17 1 (.077 .21 (.095) 1/2 .06 (.027) .08 (.036) .11 (.050) .14 (.064) .17 (.077) .20 (.091) Unless otherwise specified,all dimensions on drawings and in charts are in inches and dimensions shown in parentheses are in millimeters. CONSTRUCTION NOTES 1 I I 1.ALL WORK PER NFPA 13 2019 STANDARDS. I 1 I r J 2.EMERALD FIRE TO MODIFY EXISTING SYSTEM TO ACCOMMODATE TENANT MODIFICATIONS TO AREA OF WORK. 1 ` b 3.EMERALD FIRE EXTENT OF WORK LIMITED TO RAISING 1 I SPRINKLER EHADS TO NEW SOFFIT CEILING HEIGHT.NO W o I PENDENTS WERE RELOCATED/ADDED/REMOVED,ETC. N I 4.PENDENT SPRINKLERS SHALL NOT EXCEED 130 SQ.FT. F F SPACING. U_ L In 1 E I I 5.ALL THREADED PIPING SHALL BE SCHEDULE 40 Q I 1 7 I BLACK STEEL. Q U W M I 1 I S.ALL TESTING AND INSPECTIONS PER NFPA 13 2019. J (L J I �OQ I 1 I I Lu I 1 I I YZ0NW WI ¢ I Zmm Rmwr-' I Z JDJA I w nmaIQLL �� �I LUogcl) ' WNALMART SUPERCENTER _ ARLINGTON I w, zl WI w �—��W wl I I I I I I I I I P I AREA OF WORK I I I � I O FIRE SPRINKLER PLAN z.. 2 WALMARTARLINGTON 18" -0" N City of Arlington SHEET SIZE IS TRUE e,�4 Building Department SCALE WHEN ABOVE Sprinkler Legend APPROVED LINE MEASURES AS NOTED Symbol Manufacturer SIN Modelauanti K-Factor Type Size Response Finish Temperature Note Kevin Olander- 09/02/2025 Tyco 3 -FRB 6 5.8 Fentlent 11 Qulek 11-1 155•F REVISIONS: roJx1=8 No changes authorized unless approved by ,ovonJoc the Building Official ° )000000000= Al SECTION DETAIL LEGEND DETAIL NUMBER U X W SITE MAP FPX FP PAGE NUMBER vj O 1 30'-0 N w QX Qx 4J SYMBOLS LEGEND rw N O wwN w —-+ EXISTING PIPE Z m T 1f FLEXIBLE DROP U 3 O r Z o EX. PENDENTTO REMAIN Z Z N FLEX DROP DETAIL 0. i I--ti O Z �i .i O EX. UPRIGHT TO REMAIN I.-�I-- J Flex Q O Z IL c:JiZ Hose J�� O r ro xo«x Pipe - ..: c w ` O CL w U. MEABRY Arlo FLEX DROP DETAIL A !� ' r* N MEllT ururr MEAT unury J r ,t •` r DRAW BY, CS/MH AREA OF WORK VIEW « onre 08/26/25 91�1 oe n: 225059 SHEET NO: BULKHEAD SECTION AT DEMO BULKHEAD SECTION AT FPS BAKERY AND MEAT UTILITY BAKERY AND MEAT UTILITY r rx..xxrxxux.vmw ;1 SECTION VIEW 1 E ..Id Fi,.,HBIIBngren 1 VICINITY MAP 7223-0107-C Level3 11 O r Em==ltl Fir--LLC 3 r EMERAFL9 11 NOT TO SCALE NTS I 1 B-2S- 11 CITY OF ARLINGTON 18204 59th Avenue NE,Arlington,WA 98223 INSPECTIONS:360-403-3417-Permit Center:360-403-3551 BUILDING PERMIT 4010 172ND ST Permit#: 6688 Parcel#:00930300000301 PERMIT EXPIRES 180 DAYS AFTER DATE OF ISSUANCE. Scope of Work:Fire Sprinkler TI modification to meet client and code requirements Valuation:3000.00 CONTRACTOR Walmart,Inc. Emerald Fire Emerald Fire LLC PO BOX 8050 M/S 0555 11505 Burnham Dr STE 201 11505 Burnham Dr BENTONVILLE,AR 72712-8050 Gig Harbor Gig Harbor,WA 98332 2538572056 2538572056 UC:602-211-955 EXP:05/31/2026 LIC:EMERAFL980MR EXP:07/19/2026 MECHANICAL CONTRACTOR PLUMBING CONTRACTOR LIC#: EXP: LIC#: EXP: W JOB DESCRIPTION PERMIT TYPE: FIRE SPRINKLER CODE YEAR: 2021 STORIES: 1 CONST.TYPE: VA DWELLING UNITS: OCC GROUP: B;Business BUILDINGS: OCC LOAD: PERMIT APPROVAL The issuance or granting of this permit shall not be construed to be a permit for,or approval of,any violation of this Code or any other ordinance or order of the City,of any state or federal law,or of any order,proclamation,guidance advice or decision of the Governor of this State.To the extent the issuance or granting of this permit is interpreted to allow construction activity during any period of time when such construction is prohibited or restricted by any state or federal law,or order,proclamation,guidance advice or decision of the Governor of this State,this permit shall not authorize such work and shall not be valid.The building official is authorized to prevent occupancy or use of a structure where in violation of this Code,any other City ordinances of this jurisdiction or any other ordinance or executive order of the City,or of any state or federal law,or of any order,proclamation,guidance advice or decision of the Governor.The building official is authorized to suspend or revoke this permit if it is determined to be issued in error or on the basis of incorrect,inaccurate or incomplete information,or in violation of any City ordinance,regulation or order,state or federal law,or any order,proclamation,guidance or decision of the Governor. I AGREE TO COMPLY WITH CITY AND STATE LAWS REGULATING CONSTRUCTION AND IN DOING THE WORK AUTHORIZED THEREBY;NO PERSON WILL BE EMPLOYED IN VIOLATION OF THE LABOR CODE OF THE STATE OF WASHINGTON RELATING TO WORKMEN'S COMPENSATION INSURANCE AND RCW 18.27. THIS APPLICATION IS NOT A PERMIT UNTIL SIGNED BY THE BUILDING OFFICIAL OR HIS/HER DEPUTY AND ALL FEES ARE PAID. IT IS UNLAWFUL TO USE OR OCCUPY A BUILDING OR STRUCTURE UNTIL A FINAL INSPECTION HAS BEEN MADE AND APPROVAL OR A CERTIFICATE OF OCCUPANCY HAS BEEN GRANTED.IBC I10/IRC110. SALES TAX NOTICE: Sales tax relating to construction and construction materials in the City of Arlington must be reported on your sales tax return form and coded City of Arlington#3101. 9/3/2025 09/03/2025 Applicant Signature Date Building Official Date _ CONDITIONS Adhere to approved plans.Permit shall be onsite for inspections. Call for inspections. The property owner shall ensure that the construction project complies with all applicable zoning codes and regulations.The property owner shall also ensure that the construction project does not cause any adverse impact on the surrounding environment or community.The property owner shall be responsible for obtaining all necessary permits and approvals from the relevant authorities before commencing construction.The property owner shall ensure that the construction project complies with all applicable design review requirements. THIS PERMIT AUTHORIZES ONLY THE WORK NOTED.THIS PERMIT COVERS WORK TO BE DONE ON PRIVATE PROPERTY ONLY.ANY CONSTRUCTION ON THE PUBLIC DOMAIN(CURBS,SIDEWALKS,DRIVEWAYS, MARQUEES,ETC.)WILL REQUIRE SEPARATE PERMISSION. T PERMIT FEES Date Description Fee Amount 09/03/2025 Web Only-Fire System Plan Review $200.00 09/03/2025 Credit Card Service $6.00 09/03/2025 Processing/Technology $25.00 09/03/2025 Fire Sprinkler System $175.00 Total Due: $406.00 Total Payment: S406.00 Balance Due: $0.00 CALL FOR INSPECTIONS Call by 3:30 pm for next day inspection,allow 48 hours for Fire Inspections When calling for an inspection please leave the following information: Permit Number,Type of Inspection being requested,and whether you prefer morning or afternoon INSPECTION INFORMATION I Pass/Fail CONSTRUCTION NOTES 1 I I 1.ALL WORK PER NFPA 13 2019 STANDARDS. I 1 I r J 2.EMERALD FIRE TO MODIFY EXISTING SYSTEM TO ACCOMMODATE TENANT MODIFICATIONS TO AREA OF WORK. 1 ` b 3.EMERALD FIRE EXTENT OF WORK LIMITED TO RAISING 1 I SPRINKLER EHADS TO NEW SOFFIT CEILING HEIGHT.NO W o I PENDENTS WERE RELOCATED/ADDED/REMOVED,ETC. N I 4.PENDENT SPRINKLERS SHALL NOT EXCEED 130 SQ.FT. F F SPACING. u_ L In 1 E I I 5.ALL THREADED PIPING SHALL BE SCHEDULE 40 Q I 1 7 I BLACK STEEL. Q U W M I 1 I S.ALL TESTING AND INSPECTIONS PER NFPA 13 2019. J (L J I �OQ I 1 I I Lu I 1 I I YZ0NW WI ¢ I Zmm Rmwr-' I Z JDJA I w nmaIQLL �� �I LUogc') ' WALMART SUPERCENTER ARLINGTON I w, zl WI w �-��W _ wl I I I I I I I I I P I AREA OF WORK YYI I I I � I O FIRE SPRINKLER PLAN 2 WALMARTARLINGTON 1'.. 1•• N SHEET SIZE IS TRUE o r z a SCALE WHEN ABOVE LINE MEASURES AS Sprinkler Legend NOTED Symbol Manufacturer SIN Model Quanti K-Factor Type Size Response Finish Temperature Note Tyco 3 -FRB 6 5.8 Pentlent X Qulek Bress 155°F REWWONS: Total=8 J000 0 0( 1 � Al SECTION DETAIL LEGEND DETAIL NUMBER U X W SITE MAP LFPX FP PAGE NUMBER vj O 1 30'-0 N w QX Qx 4J SYMBOLS LEGEND rw N O wwN (n --+ EXISTING PIPE Z w ...... .. .......r 1f FLEXIBLE DROP 11 N O Z 0 o EX. PENDENTTO REMAIN �Z Z N FLEX DROP DETAIL 0. i ~ti O z 7 �i .i O EX. UPRIGHT TO REMAIN J Flex ° ' Q O Z d c z Hose J w O r ro xe«x Pipe - ..: 0 w w �,�o ® LL .� MEABRY FLEX DROP DETAIL MEAT- MEAT unury J r ,t •` r oJuwN ev CS/MH AREA OF WORK VIEW '�; ,,,, GATE: 08/26/25 q} 1��.: 91�1 oe n: 225059 SHEET NO: BULKHEAD SECTION AT DEMO BULKHEAD SECTION AT FPS BAKERY AND MEAT UTILITY BAKERY AND MEAT UTILITY r re..xerxxue.vmw ;1 SECTION VIEW r Michael TOAtl Mellengren 1 VICINITY MAP 7223-0107-C Level3 11 O r Em==ltl File, ����� II 3 r EMERAFL9 11 NOT TO SCALE NTS ; 1 B-2S- 11 i FIRE SPRINKLER PERMIT APPLICATION • Community and Economic Development City of Arlington• 18204 59th Ave NE•Arlington,WA 98223 • Phone(360) 403-3551 Type of Permit: ❑ New Installation ✓❑ System Modification ❑ Phased Installation Property Address. 4010 172nd St NE Suite No.: Project Valuation: 3000 Lot#: Parcel ID No.: 00930300000301 Preferred Contact: ❑ Owner ❑Applicant ❑ Contractor Project Description: Fire Sprinkler TI to meet client and code requirements Owner Name: Jackson Dean Construction Phone No.: Email Address: Cell No.: Mailing Address: City: State: Zip: Applicant Name: Rex Rainsberger Phone No.: Email Address: Same as contractor Cell No.: Mailing Address: City: State: Zip: Contractor Name: Emerald Fire Office No.: 253-857-2056 Email Address: permits@emeraldfirellc.com emeraldfirellc.com Cell No.: Mailing Address: 11505 Burnham Dr city: Gig Harbor State: WA zip: 98332 L&I Contractor License Number: EME RAF L950MR Expiration Date: 0712026 SUBMITTAL REQUIREMENTS: Provide Information on All Equipment to be Installed Prior to Installation ELECTRONIC FILES OF THE FOLLOW: ❑ Complete and Scaled Plans ❑ Hydraulic Calculations Q Equipment Specifications for Each Fire Sprinkler Permit Application ❑ Specification Sheets ❑ Wiring Diagrams (Point to Point Wiring) ❑ Electrical Plans,if applicable FIRE SPRINKLER SYSTEMS (105.7.1, 105.7.4, 105.7.11) ** DEVICES include separate individual portions of a Fire Sprinkler System such as: Sprinklers Heads, Risers, Valves, Pull Stations, and other such devices. (Each piece is one device) PLAN REVIEW FEES Less than $5,000.00 = $100.00 $5,000.00 &over-based on project valuation (Plan Review Fee is 65%of project valuation as calculated per Table 4-1) REV11.2020 Page 1 of 3 REINSPECTION / PHASED INSTALLATION INSPECTIONS Submit Phasing Plan with Application - review and approval required REINSPECTION FEES SHALL BE PAID PRIOR TO INSPECTION FEE Reinspection/Phased Installation fee is charged per hour (1 hour minimum) $75.00 Hydrostatic Pressure Test(1 test included per permit) $150.00 Cover Inspection (1 cover inspection included per permit) $75.00 Fire Pump (1 fire pump inspection per permit) inspection requires 2 hours $150.00 ✓❑ TENANT IMPROVEMENT OR SYSTEM MODIFICATION (NFPA 13/13R) Number of Devices" Device Fee Subtotal 1to2 $ 75.00 = $ 3 to 5 $125.00 = $ 6 to 10 $175.00 = $ 175 11 to 20 $225.00 = $ 21 to 40 $300.00 = $ 41 to 100 $375.00 = $ 101 to 200 $475.00 = $ 201 to 300 $575.00 = $ > 300 $600.00 plus$50.00 per 100 additional devices(round up) Total Number of Devices = 6 $600.00 + 1 $ 175 = $ 175 Hydraulically Designed Systems Yes ❑ No ❑ Yes = Permit Fee x 2 $ PERMIT FEE SUBTOTAL $ NEW COMMERCIAL SYSTEM (NFPA 13/13R) Number of Devices" Device Fee Subtotal 1 to 100 $375.00 = $ 101 to 200 $475.00 = $ 201 to 300 $600.00 = $ > 300 $625.00 plus$50.00 per 100 additional devices(round up) Total Number of Devices = $625.00 + 1 $ _ $ Hydraulically Designed Systems Yes ❑ No ❑ Yes = Permit Fee x 2 $ PERMIT FEE SUBTOTAL $ RESIDENTIAL (NFPA 13D) Number of Devices" Device Fee Subtotal 1 to 10 $175.00 = $ 11 to 25 $225.00 = $ 26 + $275.00 = $ *NFPA 13D SYSTEM INSTALLED(NOT REQUIRED)Permit Fee Reduced 50% = $ PERMIT FEE SUBTOTAL $ REV2022 Page 2 of 3 ❑ HOOD SUPPRESSION SYSTEM Type of System No. of Units Cost per Unit Subtotal Pre-Engineered x $200.00 = $ Custom Engineered x $275.00 = $ PERMIT FEE SUBTOTAL $ ❑ STANDPIPE SYSTEM Type of Standpipe No. of Units Cost per Unit Subtotal Class I - new or existing x $150.00 = $ Class II - new or existing x $150.00 = $ PERMIT FEE SUBTOTAL $ ❑ FIRE PUMP Fire Pump x $300.00 each = $ PERMIT FEE SUBTOTAL $ ❑ SPRAY BOOTHS (105.7) &INDUSTRIAL OVENS (105.7.7) NOTE.SEPARATE SPRINKLER PERMIT REQUIRED Type of Booth No. of Units Cost per Unit Subtotal Pre-Engineered w/documents x $150.00 = $ Site-built or used w/o documents x $250.00 = $ Industrial Oven x $250.00 = $ PERMIT FEE SUBTOTAL $ Plan review fee due at time of submittal TOTAL PERMIT FEE $ 175 PLAN REVIEW FEE $ 100 Processing/Technology Fee $25.00 TOTAL $ 300 I hereby certify that I am the ❑ Owner, ❑Applicant, ❑■ Contractor,and authorized to sign this application and that the above information is correct and construction on, and the occupancy and the use of the above-described property will be in accordance with the laws,rules and regulation of the State of Washington,and the City of Arlington. Rex Ra i n s b e rg e r 8/26/2025 Signature Print Name Date SAVE PRINT REV2022 Page 3 of 3 Permit#: 6688 Permit Date: 08/26/25 Permit Type: FIRE SPRINKLER Project Name: Walmart Arlington Applicant Name: Emerald Fire Applicant Address: 11505 Burnham Dr STE 201 Applicant, City, State, Zip: Gig Harbor Contact: Rex Rainsberger Phone: 2538572056 Email: permits@emeraldfirellc.com Scope of Work: Fire Sprinkler TI modification to meet client and code requirements Valuation: 3000.00 Square Feet: 500 Number of Stories: I Construction Type: VA Occupancy Group: B; Business ID Code: Permit Issued: 09/03/2025 Permit Expires: 03/03/2026 Form Permit Type: FIRE SPRINKLER Status: COMPLETE Assigned To: Hannah Hardwick Property Parcel# Address Legal Description Owner Name Owner Phone Zoning 569 Other Retail 00930300000301 4010 172ND ST Walmart,Inc. Trade-Apparel& Accessories NEC Contractors Contractor Primary Contact Phone Address Contractor Type License License# Emerald Fire LLC 2538572056 11505 Burnham CONSTRUCTION UBI 602-211-955 Dr CONTRACTOR 11505 Burnham CONSTRUCTION Construction Emerald Fire LLC 2538572056 EMERAFL980MR Dr CONTRACTOR Contractor Inspections Date Inspection Type Description Scheduled Date Completed Date Inspector Status FS07.FIRE onsite contact is shane 09/17/2025 SPRINKLER FINAL Rubash,253-606-1190 09/19/2025 09/19/2025 FIRE Approved Requests Sam Plan Reviews Date Review Type Description Assigned To Review Status 08/26/2025 FIRE SPRINKLER BUILDING Approved 08/26/2025 FIRE SPRINKLER TI for deli remodel FIRE Approved Fees Fee Description Notes Amount Enter 1 if permit is for:fire alarm,or fire Web Only-Fire System Plan Review sprinkler $200.00 Credit Card Service $6.00 Processing/Technology $25.00 Fire Sprinkler System Commercial NFPA 13/13R $175.00 Credit Card Service $6.00 Total $412.00 Attached Letters Date Letter Description 09/03/2025 Building Permit 08/26/2025 Web Form-Building Application Payments Date Paid By Description Payment Type Accepted By Amount 08/26/2025 Keith Hillstrom 241321419 $6.00 08/26/2025 XBP Conf: $200.00 241321419 09/03/2025 Keith Hillstrom 241937898 Hannah Hardwick $6.00 09/03/2025 XBP Conf: $200.00 241937898 Outstanding Balance $0.00 Notes Date Note Created By: 02/02/2026 Expiration Notice sent LaNay Hendrick Uploaded Files Date File Name 09/03/2025 28093862-Permit Issued.pdf 09/03/2025 28093855-20250826 BLD6688 Approved Plans.pdf 08/26/2025 dfd86c96c496f849006907bc68a0967e walmart arlington fpplan.pdf 08/26/2025 e5589423ccl2422fd7f2cl5ld497e0a4 wm arlington application.pdf 08/26/2025 192b63a90e63397b304flf2ac2f8a00b wm arlington product data.pdf