The URL can be used to link to this page

Home My WebLink About19721 47th Ave Ne_BLD2172_2026 • Endeavor 0 IL TM All Wood Stove ZOP• - Owner's Manual nm • Freestanding Stove • Mobile-Home Approved -- • Alcove Approved • Hearth-Stove Approved J Save these instructions for future reference AWARNING HOT GLASS WILL CAUSE BURNS. DO NOT TOUCH GLASS UNTIL COOLED, NEVER ALLOW CHILDREN TO TOUCH GLASS. SAFETY NOTICE: If this appliance is not properly installed, a house fire may result. For your safety, follow the installation directions. Contact local building or fire officials about restrictions and installation inspection requirements in your area. © Copyright 2015, T.I. TM $10.00 100-01334 C US L i ste d �ISTO TRAVIS INDUSTRIES 4131122 Intertek HOUSE OF FIRE Tested to: ULC 1482, ULC S627, & ULC S628 Introduction Introduction We welcome you as a new owner of a Lopi Endeavor wood-burning stove. In purchasing a Lopi Endeavor you have joined the growing ranks of concerned individuals whose selection of an energy system reflects both a concern for the environment and aesthetics. The Lopi Endeavor is one of the finest appliances the world over. This manual will explain the installation, operation, and maintenance of this appliance. Please familiarize yourself with the Owner's Manual before operating your appliance and save the manual for future reference. Included are helpful hints and suggestions which will make the installation and operation of your new appliance an easier and more enjoyable experience. We offer our continual support and guidance to help you achieve the maximum benefit and enjoyment from your appliance. Important Information No other Lopi Endeavor appliance has the same serial number as yours. The serial number is stamped onto the label on the back of the appliance. Register your warranty online at: traviswarranty.com This serial number will be needed in case you require Save Your Bill of Sale. service of any type. To receive full warranty coverage, you will need to Model: Lopi Endeavor ND show evidence of the date you purchased your heater. We suggest that you attach your Bill of Sale to this Serial Number: page so that you will have all the information you need in one place should the need for service or information Purchase Date: occur. Purchased From: NATIONAL We suggest that our woodburning hearth FIREPLACE INSTITUTE° products be installed and serviced by Elprofessionals who are certified in the U.S. by the National Fireplace Institute® (NFI) as NFI Woodburning Specialists or who are certified in Canada by d CERTIFIED Wood Energy Technical Wood Energy Training (WETT)• Technical Training w.wwnficertified.org ©Travis Industries 100-01334 4131122 Safety Precautions 3 Introduction ......................................................2 Understandinq Your Heater's Combustion Important Information......................................2 System............................................................22 Installation Options..........................................6 Burning Your Heater......................................22 Features............................................................6 Optional Blower Operation...........................23 Heating Specifications.....................................6 Re-Loading the Stove....................................23 Dimensions.......................................................6 Overnight Burn...............................................23 Emissions.........................................................6 Normal Operating Sounds............................23 Packing List......................................................7 Hints for Burning ...........................................24 Planning the Installation..................................7 Selecting Wood..............................................24 Preparation for Installation....................................7 Why Dry Wood is Key.........................................24 Additional Accessories Needed for Installation.....7 Wood Cutting and Storage..................................24 Stove Installation Considerations..........................7 Do Not Burn List..................................................25 Floor Protection Requirements......................8 Troubleshooting.............................................26 Stove Placement Requirements.....................8 Daily Maintenance (while stove is in use)...27 Clearances........................................................8 Remove Ash (if necessary).................................27 Top View-Straight Installation .............................9 Clean the Glass(if necessary)............................27 Top View-Corner Installation...............................9 Monthly Maintenance (while appliance is in Chimney Connector Requirements..............10 use)..................................................................28 Chimney Requirements.................................11 Door and Glass Inspection..................................28 Creosote-Formation and Need for Removal.....28 Chimney Termination Requirements...........12 Yearly Maintenance.......................................29 Outside Air Requirements.............................12 Touch-Up Paint...................................................29 Alcove Installation Requirements................13 Cleaning the Air Duct and Blower(if applicable).29 Mobile Home Requirements..........................14 Firebrick and Baffle Inspection............................29 Standard Ceiling with a Factory Built Chimney...15 Door Parts.......................................................30 Cathedral Ceiling with a Factory Built Chimney..15 Replacing the Glass............................................30 Exterior Factory Built Chimney............................16 Replacing the Door Gasket.................................30 Hearth Stove Positive Connection ......................16 Replacing the Door Handle.................................30 Hearth Stove Direct Connection..........................17 Firebox Parts 31 .................................................. Interior or Exterior Masonry Chimney.................17 Floor and Side Firebrick Removal & Replacement31 Safety Notice ..................................................18 Baffle Removal & Replacement....................32 Before Your First Fire....................................18 Air Tube Removal & Replacement 32 ............... Verify the Installation...........................................18 Listing Label........................................................34 Curing the Paint..................................................18 Carbon Monoxide(CO)Emissions......................18 Door Shell Installation...................................35 Over-Firing the Stove..........................................18 Nickel (Cast Iron)Doors Only.............................35 Opening the Door...........................................19 Stove Leg Installation....................................37 Bypass Operation ..........................................19 Pedestal (Part#99200106)............................38 Starting a Fire.................................................20 Using Outside Air with the Pedestal....................38 Adjusting the Burn Rate................................21 Outside Air Boot Installation (Part number Approximate Air Control Settings........................21 99200134)........................................................39 ©Travis Industries 100-01334 4131122 Precautions4 Safety The viewing door must be Gasoline or other flammable closed and latched during liquids must never be used to operation. start the fire or"Freshen Up"the Smoke from this appliance may fire. Do not store or use active a smoke detector when as gasoline or other flammable the door is open. liquids in the vicinity of this Never block free airflow through appliance. the air vents on this appliance. This appliance is designed and Ashes must be disposed in a approved for the burning of cord 0 metal container with a tight lid wood only. Do not attempt to and placed on a non- burn any other type of fuel other combustible surface well away than cord wood in this ASHES from the home or structure. appliance, it will void all warranties and safety listings. Do not touch the appliance while Keep furniture, drapes, curtains, it is hot and educate all children wood, paper, and other of the danger of a high- combustibles a minimum of 36" temperature appliance. Young away from the front of the children should be supervised 36" appliance. when they are in the same room as the appliance. This appliance must be properly Contact your local building installed to prevent theROk officials to obtain a permit and possibility of a house fire. Theinformation on any installation instructions must be strictlyrestrictions or inspection adhered to. Do not use requirements in your area. makeshift methods orNotify your insurance company compromise in the installation. of this appliance as well. Inspect the chimney connector and chimney at least twice This appliance must be monthly and clean if necessary. connected to a listed high Creosote may build up and Type Clay temperature (UL 103 HT) cause a house fire. HT Liner residential type chimney or an Do not connect this appliance to approved masonry chimney with any chimney serving another a standard clay tile, or stainless appliance. steel liner. ©Travis Industries 100-01334 4131122 Safety Precautions 5 When installed in a mobile home, this appliance must be Do not place clothing or other bolted to the floor, have outside I flammable items on or near this Mobile air, and not be installed in the appliance. bedroom (Per H.U.D. Home requirements). Check with local building officials. 0 Never try to repair or replace This wood heater has a any part of this appliance unless manufacturer-set minimum low instructions are given in this a burn rate that must not be manual. All other work must be altered. It is against federal done by a trained technician. Q regulations to alter this setting or Do not make any changes or otherwise operate this wood modifications to an existing heater in a manner inconsistent masonry fireplace or chimney to with operating instructions in this install this appliance. manual. Allow the appliance to cool before carrying out any Over-firing the appliance may maintenance or cleaning. /� cause a house fire. If a unit or chimney connector glows, you are over-firing. Maintain the door and glass seal Do not use a grate or other and keep them in good device to elevate the fire off of condition. the firebox floor. Burn the fire Do not operate this heater with directly on the bricks. broken or missing glass. Avoid placing wood against the glass when loading. Do not slam the door or strike the glass. Do not throw this manual away. Travis Industries, Inc. grants This This manual has important no warranty, implied or Manual operating and maintenance stated, for the installation or instructions that you will need at maintenance of your a later time. Always follow the appliance, and assumes no instructions in this manual. responsibility of any consequential damage(s). Smoke and CO Detectors: Make sure your home has a working smoke detector, especially near any bedrooms. We recommend having a smoke and/or CO detector in the same room as the wood heater for additional safety. Proposition 65 Warning: Fuels used in gas,woodburning or oil fired appliances, and the products of combustion of such fuels, contain chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. California Health&Safety Code Sec. 25249.6 ©Travis Industries 100-01334 4131122 • Stove Installation • qualified installers only) Installation Options Features • Freestanding 0 2.2 Cubic Foot Firebox Volume (62 Liter) • Freestanding in an Alcove 0 Single Operating Control • Freestanding in a Mobile Home 9 Accepts Logs Up to 18" Long (457mm) • Freestanding Hearth Stove 9 Steel Plate Construction (5/16" & 3/16") (8mm & 10mm) • Heavy Duty Refractory Firebrick • Optional High-Tech Blower Heating Specifications Approximate Maximum Heating Capacity (in square feet)* 1,200 to 2,000 Maximum BTUs per Hour(Cord Wood Calculation) 72,400 Maximum Burn Time Up to 10 Hours * Heating capacity will vary depending on the home's floor plan, degree of insulation, and the outside temperature. It is also affected by the quality and moisture level of the fuel. This model was not tested for efficiency however it is assigned a default efficiency of 63% by the EPA under previous subpart AAA. Efficiency of this wood heater will be affected by the operational burn rate and the moisture content of the wood used as fuel. Dimensions 23-1/2" \/ 24"610mm 597mm 5-3/4"146mm '�� 6"152mm o 1-3/4"44mm 1 Note: \ Measure side,corner,and back clearances from the stove top. Measure front clearances from the stove face. Height: Sculptured or Cast Legs....30-5/8"778mm Pedestal.............................34-5/8"879mm Weight:448 Lbs. 203 Kilos Figure 1 Emissions This heater meets the 2015 U.S. EPA's crib wood emission limits for wood heaters sold after May 15, 2015. Tested to Method 28, 5H this heater has been shown to deliver heat at rates ranging from 9,300 to 42,200 BTU/hr and an emission value of 1.9g/h. ©Travis Industries 100-01334 4131122 Stove • n (for qualified installers only) SAFETY NOTICE: Please read this entire manual before you install and use your new room heater. Failure to follow instructions may result in property damage, bodily injury, or even death. Contact local building or fire officials about restrictions and installation inspection requirements in your area. Packing List • Wood moisture meter • Bypass tool Planning the Installation 0 We suggest that you have an authorized Travis Industries dealer install your stove. If you install the stove yourself, your authorized dealer should review your installation plans. 0 Check with local building officials for any permits required for installation of this stove and notify your insurance company before proceeding with installation. 0 The location of your wood heater in your home will decide how affectively the heat produced will spread throughout your house. Attention to the home design with consideration of natural convection and air circulation should be taken into account when choosing the placement of your heater within the home. Preparation for Installation • Check for damage to the exterior of the stove (dents should be reported, scratches can be fixed by applying touch up paint). (• Check the interior of the firebox (replace cracked firebrick and make sure baffle is in place). UThe stove can be lightened by removing the firebricks and baffle (page 31)- replace before operation. Additional Accessories Needed for Installation • Door Shell Old Part#(includes ashlip trim) New Part#(no ashlip trim) Small Black 99300195 96100634 Small Brass 99300196 96100635 Small Pewter 99300197 96100636 • Legs or Pedestal Stove Installation Considerations The table below details the six most common types of installations and the considerations for each type. Alternative methods of installation are available if they comply with local building codes. Installation Type Considerations Standard Ceiling with a Factory Built Chimney Requires ceiling and roof penetration (Page 15) 0Provides best draft Cathedral Ceiling with a Factory Built Chimney 0Cathedral style chimney support required (Page 15) Provides best draft Exterior Factory Built Chimney Uses two elbows to route chimney outside (Page 16) Exterior chimney is hidden from the room • Elbows reduce draft • Optional exterior chase reduces cold air blockage Hearth Stove Positive Connection Utilizes existing masonry or zero clearance(metal)chimney (Page 16) Provides good draft due to full reline • Easier to clean than direct or horizontal hearth stove Hearth Stove Direct Connection Utilizes existing masonry or zero clearance(metal)chimney (Page 17) Requires construction of a"block-off plate" • Draft reduced due to elbows&chimney cross section Interior Masonry Chimney Utilizes existing masonry chimney(not approved for zero clearance (Page 17) (metal)fireplaces) ©Travis Industries 100-01334 4131122 Stove Installation • qualified installers • Floor Protection Requirements • Stove must be placed on the Travis Industries legs or pedestal. • Floor protection must extend to the sides, rear, and front of the stove (see "Clearances" below for minimum floor protection). NOTE: When installed with reduced clearance connector, the clearance to the back wall may be less than the floor protection requirement. In this case, the floor protection must extend to the wall. • Floor protection must be non-combustible and at least .018"thick (26 gauge). Stove Placement Requirements /A\ Clearances may be reduced by methods specified in NFPA 211, listed wall shields, pipe shields, or other means approved by local building or fire officials. • Stove must be placed so that no combustibles are within, or can swing within (e.g. drapes, doors), 36" (914mm)of the front of the stove • If the stove is placed in a location where the ceiling height is less than 7' (2134mm), it must follow the requirements in the section "Alcove Installation Requirements" • Must maintain the clearances to combustibles listed below(drywall, furniture, etc.): Clearances • The following clearances must be met (see Figure 2 and Figure 3) Clearance Requirements: Single-wall Connector Reduced Clearance* A Sidewall to stove 15" 381 mm 13" 330mm B Back-wall to stove 15" 381 mm 4.26— 108mm** C Corner-wall to stove 15" 381 mm 6.5" 165mm D Connector to sidewall 24" 610mm 21.5" 546mm E Connector to back-wall 17.75" 451 mm 6.5" 165mm F Connector to corner-wall 24" 610mm 15" 381 mm G Side&Rear Floor Protector 6" 152mm (US) 6" 152mm (US) 8"200mm (Canada) 8"200mm (Canada) H Front Floor Protector 16"406mm (US) 16"406mm (US) 18"450mm (Canada) 18"450mm (Canada) *Reduced clearance installations require one of the chimneys and connectors listed below: AMERI-TEC model DCC with model HS chimney DURAVENT model DVL with DURATEC or DURA-PLUS chimney GSW Super Chimney Twenty-One connected directly to appliance I.C.C.Excel(2100-2 Can.)(103-HT USA)chimney with HP connector METALFAB model DW connector with TG chimney OLIVER MACLEOD PROVENT model PV connector with model 3103 chimney SECURITY model DP connector with SECURITY model ASHT or S2100 chimney SELKIRK METALBESTOS model DS connector with model SSII chimney Standard Masonry Chimney with any one of the above listed connectors NOTE: Reduced clearance connectors may not connect to the flue collar—an appliance adapter may be required. **If using the optional GreenStart Igniter, 6" (153mm) clearance is required to allow for igniter installation. NOTE: Reduced clearance connectors may not connect to the flue collar, an appliance adapter may be required. NOTE: Mobile home installations must use the reduced clearance connector and clearances listed above. NOTE: Standard residential installations with reduced clearance connector may use the"Connector to Wall" clearance determined by the connector manufacturer if approved by local code. This clearance is established by the connector manufacturer and falls under the connector manufacturer's listing. "Stove to Wall"clearances must always be met. ©Travis Industries 100-01334 4131122 Stove • qualified ' Top View - Straight Installation e b O Measure rear and side clearances from the 24"610mm g nearest edge of the stove top. a �5-3/4"146mm ONOTE: Vent diameter varies depending on Li brand and model. 23-1/2" 597mm OMeasure front clearances from the face of the stove (unibody). h k Figure 2 Top View - Corner Installation OMeasure rear and side clearances from the nearest edge of the stove top. f c 24"610mm O NOTE: Vent diameter varies depending on 146mm brand and model. 9 OMeasure front 23-1/2" clearances from the face 597mm i of the stove (unibody). h k Figure 3 ©Travis Industries 100-01334 4131122 1 Stove Installationqualified Chimney Connector Requirements • Chimney connector is required from the flue collar of the stove to the factory-built chimney or masonry chimney. • The chimney connector must be 6" diameter and a minimum 24 gauge black steel, or one of the reduced-clearance connectors listed on page 8. NOTE: Aluminum or galvanized steel is not allowed—these materials cannot withstand the flue temperatures and may give off toxic fumes when heated. NOTE: Standard residential installations may use single-wall connector(Mobile-Homes may not). • The chimney connector may not pass through a ceiling, attic, roof, closet, or any other concealed space (use listed UL 103 HT chimney—see "Chimney Requirements for details). DO NOT USE CONNECTOR PIPE AS CHIMNEY. • IN CANADA: Where passage through a wall or partition of combustible construction is desired, the installation shall conform to CAN/CSA-B365, Installation Code for Solid-Fuel-Burning Appliances and Equipment. • The chimney connector should be as short and direct as possible. No more than 180'of elbows (two 900 elbows, or two 45'&one 900 elbow, etc.) may be used for the entire system (connector and chimney).. Horizontal runs should slope upwards 1/4" per foot and be a maximum 36" long. • The chimney connector must be installed with the crimped end pointing downwards. This prevents creosote from leaking to the exterior of the pipe. • The chimney connector must be fastened to the stove and each adjoining section (and chimney). • Standard residential installations may use single-wall connector(Mobile-Homes may not) • Standard residential installations with reduced clearance connector may use the clearance determined by the manufacturer of the connector for the connector to wall clearance or the clearance listed in this manual. Offsets must be used to maintain the stove to wall clearance. Mobile homes must use the clearances listed in this manual under"Additional Requirements for Mobile Home Installations". ©Travis Industries 100-01334 4131122 Stove Installationqualified installers only) Chimney Requirements • DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE. • UL 103 HT Chimney must be used from the first ceiling or floor penetration to the chimney cap. • Use 6" diameter type UL 103 HT chimney from one manufacturer(do not mix brands)or code approved masonry chimney with a flue liner. • Chimney must be fastened to each adjoining section. • Follow the chimney manufacturer's clearances and requirements. • Use the chimney manufacturer's fire stops, attic guards, roof supports, and flashings when passing through a ceiling. • No more than 1800 of elbows (two 900 elbows, or two 450&one 900 elbow, etc.) may be used for the entire system (connector and chimney). NOTE: Additional elbows may be allowed if draft is sufficient. Whenever elbows are used the draft is adversely affected. Additional chimney height may be required to boost draft. b (a) Min. System Height 15' Max. System Height 33' (b) Roof Penetration and Termination (see O chimney manufacturer's requirements) b (c) Chimney Sections C i (d) Floor Penetration (see chimney manufacturer's requirements) (e) Min. air space to combustibles (see chimney manufacturer's requirements—typically 2") _ (f) Connector—see "Chimney Connector" on the O previous page. Is N E f Figure 4 Drafting Draft is the force which moves air from the appliance up through the chimney. The amount of Performance draft in your chimney depends on the length of the chimney, local geography, nearby obstructions and other factors. Too much draft may cause excessive temperatures in the appliance and may damage the heater. Inadequate draft may cause backpuffing into the room and 'plugging' of the chimney. Inadequate draft will cause the appliance to leak smoke into the room through appliance and chimney connector joints. An uncontrollable burn or excessive temperature indicates excessive draft. ©Travis Industries 100-01334 4131122 12 Stove • qualified installers only) Chimney Termination Requirements • Must have an approved cap (to prevent water from entering) • Must not be located where it will become plugged by snow or other material • Must terminate at least 3' above the roof and at least 2' above any portion of the roof within 10' (see Figure 5). Min.2' (610mm) Min. 3' (914mm) 10'(3.04M) Min.2' (610mm) 10'(3.04M) Min. 3'(914mm) Figure 5 Outside Air Requirements • Required for mobile homes & in certain localities (check with building officials). • Must not be drawn from an enclosed space (garage, unventilated crawl space). May be drawn from ventilated crawl space (a)or exterior of home (d). Must have suitable rodent/debris screen and rain protection (hood). • Requires the optional outside air kit(sku 99200139—see (c)and (e) below), air boot(for legs), or pedestal (b). • Air duct maximum length is 15' (4.57M)with a minimum cross section of 16 square inches (10404mm) or 6' (1.82M)with a minimum cross section of 7 square inches (4489mm). II II I b I a r e C d d Figure 6 ©Travis Industries 100-01334 4131122 Stove • n (for qualified installers only) Alcove Installation Requirements Whenever the stove is placed in a location where the ceiling height is less than 7' (2134mm)tall, it is considered an alcove installation. Because of the reduced height, the special installation requirements listed below must be met. • Chimney connector and chimney must be one of the following types: AMERI-TEC model DCC with model HS chimney DURAVENT model DVL with DURATEC or DURA-PLUS chimney GSW Super Chimney Twenty-One connected directly to appliance I.C.C.Excel(2100-2 Can.)(103-HT USA)chimney with HP connector METALFAB model DW connector with TG chimney OLIVER MACLEOD PROVENT model PV connector with model 3103 chimney SECURITY model DP connector with SECURITY model ASHT or S2100 chimney SELKIRK METALBESTOS model DS connector with model SSII chimney Standard Masonry Chimney with any one of the above listed connectors NOTE: Reduced clearance connectors may not connect to the flue collar—an appliance adapter may be required. • Alcoves are classified as combustible or non-combustible. Non-combustible alcoves must have walls and a ceiling that are 3 1/2" (89mm)thick of a non-combustible material (brick, stone, or concrete - see Figure 7). This non-combustible material must be spaced and ventilated at least 1" (25mm)off of all combustible materials (walls, ceiling, etc.)to allow air to move around the non-combustible walls and ceiling. All other alcoves are considered combustible. The clearances below must be met: Minimum Clearance (See the Figure 7 below) Combustible Alcove Non-Combustible Alcove A Sidewall to stove 13" 330mm 6" 152mm B Back-wall to stove 4-1/4" 108mm 2" 51mm D Connector to sidewall 21-1/2" 546mm 14-1/2" 368mm E Connector to back-wall 6-1/2" 165mm 4-1/4" 108mm G Maximum depth of alcove 48" 1219mm 48" 1219mm H Minimum width of alcove 50" 1270mm 36" 914mm J Minimum height of alcove 84" 2134mm 6" (152mm)above stove top Non-combustible alcove construction(on walls and ceiling)-see the explanation above. 0 Ventilated air space e Min.3\ co mm) non- lJ� \\1 combustible material 1"(25mm) Min. _ N �m E ' of \ Non-combustible reinforcer Figure 7 ©Travis Industries 100-01334 4131122 14 Stove • n (for qualified installers only) Mobile Home Requirements • Outside air must be installed - see "Outside Air Requirements" on page 12 • Chimney connector and chimney must be one of the following types: AMERI-TEC model DCC with model HS chimney DURAVENT model DVL with DURATEC or DURA-PLUS chimney GSW Super Chimney Twenty-One connected directly to appliance I.C.C.Excel(2100-2 Can.)(103-HT USA)chimney with HP connector METALFAB model DW connector with TG chimney OLIVER MACLEOD PROVENT model PV connector with model 3103 chimney SECURITY model DP connector with SECURITY model ASHT or S2100 chimney SELKIRK METALBESTOS model DS connector with model SSII chimney Standard Masonry Chimney with any one of the above listed connectors NOTE: Reduced clearance connectors may not connect to the flue collar—an appliance adapter may be required. • Stove placement must maintain the following clearances to combustibles (drywall, furniture, etc.) Rear heat b e A/ shield c a d O f c Measure all clearances from the nearest edge of the stove top. Figure 8 Minimum Clearance Reduced Clearance (See the illustration above) Connector A Sidewall to stove 13" 330mm B Back-wall to stove 4-1/4" 108mm C Corner-wall to stove 6-1/2" 165mm D Connector to sidewall 21-1/2" 546mm E Connector to back-wall 6-1/2" 165mm F Connector to corner-wall 15" 381 mm • If using offsets, use the connector clearance listed in Figure 9, 1 12"Min. not the connector manufacturer's clearance. 1 (305mm • The appliance must be secured to the floor(consult your building official). Secure the outside air boot to the floor and Minimum Connector stove to insure the stove does not dislocate. Clearance (as outlined above) • Mobile home installations require a spark arrester at the imum chimney termination. Cle ance Stove • The appliance must be grounded to the chassis of the mobile (as outlined above) home (consult your building official). • WARNING: DO NOT INSTALL IN SLEEPING ROOM. • CAUTION: THE STRUCTURAL INTEGRITY OF THE MOBILE HOME FLOOR, WALL, AND CEILING/ROOF MUST BE Figure 9 MAINTAINED. ©Travis Industries 100-01334 4131122 Stove • qualified installers only) 15 Standard Ceiling Chimney Cap (See the section"Chimney with a Factory Termination Requirements" Follow the chimney Built Chimney for more details) manufacturer's instructions and clearances for roof penetrations. A storm collar Chimney Sections and flashing are required (some require a radiation Insulation shield). Follow the chimney manufacturer's instructions `•. Minimum Air Space to and clearances for floor Combustibles(See penetrations. A ceiling Chimney Manufacturer's support is required, an attic Instructions-usually 2") insulation shield is required where insulation is present. Minimum 15' Chimney Connector Sections Maximum 33' Floor Protection (See the section"Floor , Stove Clearances Protection Requirements" � (See the section "Stove for more details) Placement Requirements" for more details) JXI Figure 10 Cathedral Ceiling Chimney Cap /� with a Factory (See the section "Chimney Built Chimney Termination Requirements" for more details) Follow the chimney Chimney Sections manufacturer's instructions and clearances for roof penetrations. A storm Minimum Air Space to collar,flashing, and Combustibles(See Chimney cathedral-style chimney Manufacturer's Instructions- support are required usually 2") (some require a radiation shield). Chimney Minimum 15' Connector Maximum 33' Sections Floor Protection Stove Clearances (See the section "Floor �� (See the section "Stove Protection Requirements" Placement Requirements" for more details) for more details) Figure 11 ©Travis Industries 100-01334 4131122 • Stove Installationqualified installers only) Exterior Factory Follow the chimney Built Chimney Chimney Cap manufacturer's (See the section "Chimney instructions and Termination Requirements" clearances for roof NOTE: for more details) penetrations. A storm Exterior chimneys are Chimney Sections collar and flashing are subject to greater required (some moisture and creosote Minimum Air Space to require a radiation accumulation due to the Combustibles(See shield). Chimney Manufacturer's Wall Bands lower temperatures. An Minimum 15' Instructions-usually 2") and insulated chase will Supports Maximum 33' reduce these Min. 18" Insulated Tee accumulations (the clearance to (with cleanout proper clearances to the ) chimney must be ceiling ( Follow the chimney maintained). /- �.� manufacturer's Chimney Connector instructions and Sections clearances for wall penetrations. A wall radiation shield Floor Protection (thimble)is (See"Floor required. Protection Stove Clearances Requirements" (See the section"Stove Optional for details) Placement Requirements" insulated for more details) chase CJ JlJ ggFigure 12 shin Hearth Stove _� p epventsfwatertrom Positive NOTE:The entire fireplace and entering chimney must be clean, undamaged, Connection and meet all local building codes (UBC,etc.). Damage must be NOTE: repaired prior to installation. The chimney must be 15'to 33'tall. Most factory-built chimney manufacturers The liner must be make stainless steel stainless steel connector or flexible vent. Follow chimney liners, either the liner manufacturer's flexible or rigid. This instructions installation provides a wide variety pp of installation options. Combustible Make sure to follow the Mantle manufacturer's Min. 18" Airtight Insulated instructions for Clean-Out installation and support. Remove damper or wire it open Floor Protection (See the section Floor Protection Requirements" See the section for more details) Stove Placement Requirements"for minimum clearances _- required. I I I I I I I I I I Figure 13 ©Travis Industries 100-01334 4131122 Stove • qualified installers only) 17 NOTE:The chimney must have a clay Hearth Stove Direct tile liner. If it does not,the installation Connection must use a positive connection(full reline). The entire fireplace and chimney must be clean, undamaged, Clay NOTE: and meet all local building codes(UBC, Liner etc.). Damage must be repaired prior Stainless steel This type of installation is to installation. The chimney must be chimney connector not allowed in Canada. 15'to 33'tall. must Extend 1'past Max.8" the block-off plate or NOTE: to the flue liner Direct connections require Airtight installation of an airtight, �- Insulated non-combustible block-off Combustible Mantle Clean-Out plate or damper adapter. Min. 18" — 1 Remove damper 11 or wire it open Block-off plate or damper adapter Floor Protection See the section (See the section"Floor I "Stove Placement Protection Requirements" Requirements"for for more details) minimum clearances required. I I I I I I Figure 14 Interior or Exterior NOTE:The chimney must have a Masonry Chimney clay tile liner. If it does not,the installation must use a positive connection(full reline). The ' Clay Liner entire fireplace and chimney must NOTE: be clean, undamaged,and meet Min. 18" This type of installation is all local building codes(UBC, clearance not allowed in Canada. etc.). Damage must be repaired to ceiling prior to installation. The chimney must be 15'to 33'tall. NOTE: �A This type of This type of installation See the section"Stove T installation requires requires a UBC approved Placement Requirements"for -_ a UBC approved minimum clearances required. masonry connector masonry connector or a or a factory built factory built(U.L. Listed) (U.L. Listed)wall wall thimble. Chimney connector sections thimble. See the section Make sure the "Floor Protection clean-out seals in Requirements" place. Figure 15 ©Travis Industries 100-01334 4131122 18 Operating • Appliance Safety Notice If this appliance is not properly installed, a house fire may result. For your safety, follow the installation directions. Contact local building or fire officials about restrictions and installation inspection requirements in your area. /A\ Read and follow all of the warnings on pages 4 and 5 of this manual. Before Your First Fire Verify the Installation Before starting the stove, verify that the stove is properly installed and all of the requirements in this manual have been followed. /A Keep all flammable materials 36" away from the front of the stove (drapes, furniture, clothing, etc.). Curing the Paint 2 to 4 hours Follow the steps below to cure the paint(first fire): a 4 7- a) Open doors and windows in the room to ventilate the heater during the curing process. b)Vacate the room. The fumes from the initial heating process are non-toxic but may be unpleasant. c) Slowly bring the heater to a medium burn (400oF/204'C)for 45 minutes. Then increase the burn temperature to a hot burn (600°F/315°C)for an additional 45 minutes. This will cure the paint. Door Gasket-The door gasket might adhere to the paint on the front of the heater. Leave the door slightly ajar for the first fire and be careful when opening the door after the first fire. Carbon Monoxide (CO) Emissions Smoke from wood heaters contain CO. This gas is an indication of incomplete combustion and is detrimental to the environment and to your health. The more visible the smoke, the higher the CO levels. Burning dry wood is the most significant step you can take to reduce CO emissions. It is also important to understand the combustion process so you can burn your heater efficiently. Read the manual thoroughly so that you can operate your heater in the most efficient and clean manner possible. Over-Firing the Stove DO NOT OVERFIRE THIS HEATER: Attempts to achieve heat output rates that exceed heater design specifications can result in permanent damage to the heater. This stove was designed to operate at a high temperature. But due to differences in vent configuration, fuel, and draft, this appliance can be operated at an excessive temperature. If the stove top or other area starts to glow red, you are over-firing the stove. Shut the air control down to low and allow the stove to cool before proceeding. /A Over-firing may lead to damage of plated surfaces. If you are uncertain of over-firing conditions, we suggest placing a stove thermometer(e.g. Rutland®Model 710)directly over the door on the stove top- temperatures exceeding 800° are generally considered over-firing and will void the warranty. ©Travis Industries 100-01334 4131122 Operating • • • • Opening the Door Rotate Swing the door the door handle. open. /A\ The door becomes hot during use. Use a glove to open the door if the handle is hot. 0 To prevent smoke from entering the room, open the air control before opening the door. You can also open the door a small amount and let air enter the firebox. Bypass Operation The bypass controls the flow of smoke inside the heater. When pulled out, smoke goes directly up the flue, creating more draft. When pushed in, the smoke goes around the baffle, utilizing the secondary combustion and making the heater more efficient. • When starting or re-loading, pull the bypass out. • During normal operation, push the bypass in. Bypass Pulled Out Use the included pull tool Used for starting and re-loading to operate the bypass rod O O Bypass Pushed In Used for normal operation O eO ©Travis Industries 100-01334 4131122 1 Operating • Appliance Starting a Fire Since the dawn of time man has debated the best way to start a fire. Some use the boy-scout"tee-pee"; some prefer the "tic-tac-toe" stack. Either way, review the hints and warnings below to ensure proper fire starting. • Make sure the air control is pulled out. If additional air is needed, open the doors 1/4" during the first five minutes of start-up. 0 /A Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or"freshen up" a fire in this stove. Keep all such liquids well away from the stove while it is in use. /A\ DO NOT USE CHEMICALS OR FLUIDS TO START THE FIRE. DO NOT BURN GARBAGE OR FLAMMABLE FLUIDS SUCH AS GASOLINE, NAPHTHA OR ENGINE OIL. Do not place such fuel within space heater installation clearances or within the space required for charging and ash removal. /A\ If using a firestarter, use only products specifically designed for stoves -follow the manufacturer's instructions carefully. /A\ HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE SKIN BURNS. 0 If the smoke does not pass up the chimney, ball up one sheet of newspaper, place it in the center of the firebox and light it. This should start the chimney drafting (this eliminates "cold air blockage"). 0 Use plenty of kindling to ensure the stove reaches a proper temperature. Once the kindling is burning rapidly, place a few larger pieces of wood onto the fire. ©Travis Industries 100-01334 4131122 Operating • Appliance 21 Adjusting the Burn Rate Use the air control slider to control the burn rate of the stove. See the illustration below for details. Use the air control to O change the burn rate. Low Burn High Burn (air con ro c Fosed) (air control open) 0o ly � Approximate Air Control Settings Overnight Burn Fully in to 1/8" open Medium Burn 1/8" to 5/8" open Medium High Burn 5/8" to fully open High Burn Fully open (pulled out) The air control becomes hot during operation - use gloves or a tool to prevent burns. 0 The air control may take several minutes to influence the burn rate. When making adjustments, you Umay wish to let the stove burn for 10 minutes to gauge performance. ©Travis Industries 100-01334 4131122 22 Operating • Appliance Understanding Your Heater's Combustion System This heater uses a dual combustion system detailed below: Primary Combustion: This is the combustion (fire)that takes place directly on the wood. Primary combustion determines how fast the fire burns. Air for primary combustion is supplied through the air control. When you adjust the air control you control the amount of air that reaches the fire and creates primary combustion. The air control supplies air to the air wash (the air holes above the door opening—used to help clean the glass) and through the pilot orifice (center bottom of the door opening). By using the air control, and supplying air through these two openings, you control primary combustion. Secondary Combustion: This is the combustion (fire)that does not contact the wood. Secondary combustion burns the visible emissions or smoke that is not consumed during primary combustion. During some phases of combustion you will see secondary combustion. It appears as a glowing flame at the top of the firebox. Air for secondary combustion is supplied by the air tubes at the top of the firebox. Items to Consider: • During medium and high burn rates the stove will manage secondary and primary combustion on its own. When the heater is set to a low burn rate more care is needed to ensure the secondary combustion system works properly. Make sure the stove is hot and a good coal bed is established before adjusting your heater to low burn. • Understanding the combustion system in this heater will help minimize the visible emissions this heater releases into the environment. The primary pilot orifice at the center bottom of the door opening is designed to help the secondary combustion at low burn settings. The pilot provides a small amount of air that burns up through the fuel load providing the heat and flame needed for the secondary system to ignite. The air tubes under the baffle need to remain ignited for low burns to be effective. • As you load your heater for a low burn, take care in placing the wood. This will affect how well your secondary system works as the wood is consumed. Do not block the pilot orifice. Stack wood so the pilot air can burn its way up between the pieces, helping your heater burn effectively throughout the low fire. This will reduce the visible emissions your heater produces and increase the amount of heat you get from the wood. If you are unsure how well your heater is burning look at the chimney cap to monitor visible emissions. Burning Your Heater Startinq a Fire: When starting a fire it is imperative to get the heater hot and drafting as quickly as possible. This promotes combustion and reduces emissions. There are many ways to start a fire and you will become adept as you become familiar with the way your heater burns. Before you start, make sure your burn rate setting (air control) is all the way open and the by-pass (if equipped) is open. We suggest that you use a layer of crumpled newspaper covered with a three layers of small kindling, stacked tic tac toe style with approximately'/2"-1"gaps between them. Continue to layer wood on top of the kindling with the same air gaps using slightly bigger pieces increasing in size as you stack upward with the final layer being 3-5" diameter pieces loaded on the top. This should fill the firebox. Light the newspaper in several places near the door opening. Shut the door but do not latch it, creating a small opening to allow air to feed the kindling fire. Never leave your heater unattended if your door is not latched shut. While the kindling burns the fire will heat and ignite the larger pieces above. Once the whole load is burning shut and latch the door leaving the burn rate on high. Depending on your heater, the chimney, and the outside environment, you may need to leave your bypass open for up to 20 minutes after lighting the fire. If the fire dies when you shut the bypass you will need to leave it open longer. The presence of a hot coalbed is critical to good combustion. We cannot overstate the importance of a hot coal bed before slowing your burn rate or re-loading your heater. We recommend that you allow the first ignition load of wood to burn through at the high burn rate. This will get your heater up to temperature and establish a coal bed. Reloading: When reloading a hot heater set the burn rate on high for at least 15 min before slowing it down. Low Burn: If preparing for an overnight or low burn a longer heat up period may be necessary. Reload the heater full of wood making sure there are air gaps between the wood pieces so the pilot air can burn up through the middle load keeping the secondary combustion system hot and active throughout the burn. After loading, burn the heater on high for at least 15 minutes before setting the air control to low. Excessive creosote buildup (or sooting) in the heater at the end of a low burn signifies that the heater was not hot enough and the wood load was not burned long enough on high after loading before shutting down the air control. ©Travis Industries 100-01334 4131122 Operating • Appliance 23 Optional Blower Operation The blower will turn on once the stove is up to temperature. This is typically 15 to 30 minutes after starting the fire. Follow the directions below to alter the blower speed. OFF HIGH LOW Turn the dial all the way counter- The high position is all the way counter- Turn the dial all the clockwise until it clicks off. clockwise,without clicking off. way clockwise. OF F HI OFF. Hill OFF. HI LO O LO O BLOWER BLOWER cc CONTROL CONTROL CO.. L VThe blower may be used to affect heat output (i.e.: to reduce heat output, turn the blower down). /A\ Route the power cord in a location where it will not come in contact with the appliance or become hot. Re-Loading the Stove Follow the directions below to minimize smoke spillage while re-loading the stove. 1 Open the air control all the way (pull out). 2 Open the door slightly. Let the airflow inside the firebox to stabilize before opening the doors fully. 3 Load wood onto the fire. Overnight Burn This stove is large enough to accommodate burn times up to eight hours. Follow the steps below to achieve an overnight burn. 1 Move the air control to high burn and let the stove become hot (burn for approximately 15 minutes). 2 Load as much wood as possible. Use large pieces if possible. 3 Let the stove burn on high for 15 minutes to keep the stove hot, and then turn the air control to low. 4 In the morning, the stove should still be hot, with embers in the coal bed. Stir the coals and load small pieces of wood to re-ignite the fire, if desired. 0 Differences if chimney height and draft may lower overall burn times. Normal Operating Sounds Creaks and Clicks: The 3/16"and 5/16"steel may creak or click when the stove heats up and cools down-this is normal. Blower Sounds: The blower will make a slight"humm"as it pushes air through the stove. Hint: Make sure the leveling bolts on legs are extended- preventing the hearth from amplifying any vibrations. ©Travis Industries 100-01334 4131122 24 OperatingYourAppliance Hints for Burning • Get the appliance hot before adjusting to low burn • Use smaller pieces of wood during start-up and high burns to increase temperature • Use larger pieces of wood for overnight or sustained burns • Stack the wood tightly together to establish a longer burn • Be considerate of neighbors &the environment: burn dry wood only • Burn small, intense fires instead of large, slow burning fires when possible • Learn your appliance's operating characteristics to obtain optimum performance Selecting Wood /A Burn only untreated wood. Burning other materials such as wood preservatives, metal foils, coal, plastic, sulfur, or oil may damage the stove. • Dry Wood is Key— 15-20% Wet � A moisture content Wood Wood • Dry wood burns hot, emits less / Leads / / Leads smoke and creates less creosote. ,I �yo • Split wood stored in a dry area will T° be fully dry within a year. This \I T 1\ insures dry wood. If purchasing Less pq More �� j wood for immediate use, test the Heat ��„\'1' I„�� Heat wood with a moisture meter. Some 40eads Leads experienced wood burners can "'` ` T° measure wood moisture by ^y knocking pieces together and listening for a clear"knock" and not More Smoke Less Smoke a "thud". and Creos toe and Creostoe • Testing Wood Moisture—Split a piece of wood down the middle and test the center using a wood moisture meter. Why Dry Wood is Key When burned wet wood must release water stored within the wood. This cools the fire, creates creosote, and hampers a complete burn. Ask any experienced wood burner and he or she will agree: dry wood is crucial to good performance. Wood Cutting and Storage Cut wood to length and Store the wood off the ground in a chop into quarters. covered area. Allow for airflow Air Flow around the wood to dry the wood. [ - - - . ' - _ b � Air Flow Air Flow 1r ©Travis Industries 100-01334 4131122 Operating • Appliance 25 Do Not Burn List This heater is designed to burn natural wood only. Higher efficiencies and lower emissions generally result when burning air dried seasoned hardwoods, as compared to softwoods or to green or freshly cut hardwoods. DO NOT BURN: (1) Garbage; (2) Lawn clippings or yard waste; (3) Materials containing rubber, including tires; (4) Materials containing plastic; (5) Waste petroleum products, paints or paint thinners, or asphalt products; (6) Materials containing asbestos; (7) Construction or demolition debris; (8) Railroad ties or pressure-treated wood; (9) Manure or animal remains; (10) Salt water driftwood or other previously salt water saturated materials; (11) Unseasoned wood; or (12) Paper products, cardboard, plywood, or particleboard. The prohibition against burning these materials does not prohibit the use of fire starters made from paper, cardboard, saw dust, wax and similar substances for the purpose of starting a fire in an affected wood heater. Burning these materials may result in release of toxic fumes or render the heater ineffective and cause smoke. ©Travis Industries 100-01334 4131122 • Operating • Appliance Troubleshooting Problem Possible Cause Smoke Enters Room During 0 Open the air control (pg. 21). Start-Up 0 Cold Air Blockage- burn a piece of newspaper to establish a draft. • If the flame is not getting enough air, a small crack in the door is all that is needed. Kindling Does Not Start - Fire • Open the air control (pg. 21). Smolders 0 Not enough starter paper- use additional newspaper if necessary. • If the flame is not getting enough air, a small crack in the door is all that is needed. Smoke Enters Room While Re- 0 Open the air control before opening the door(pg. 21). Loading 0 Let the air stabilize before fully opening the door. Then open the door approximately 1 inch. Let air go into the firebox for a few seconds. Once the smoke appears to be flowing up the chimney consistently, open the door. • Insufficient Draft- Chimney height and outside conditions can negatively affect draft. In these cases a small amount of smoke may enter the home. Adding more piping or a draft-inducing cap may help. Stove Does Not Burn Hot Enough • Wood is Wet-see the section "Selecting Wood" on page 24 for details on wood. • Make sure the air control is all the way open. Slide the control back and forth to insure the control is not stuck. • Insufficient Draft- Chimney height and outside conditions can negatively affect draft. In these cases the fire may burn slowly. Adding more piping or a draft-inducing cap may help. Blower Does Not Run 0 Stove is Not Up to Temperature-This is normal. The blower will come on when the stove is hot- usually 15 to 30 minutes. • Electricity is Cut to the Blower- Check the household breaker or fuse to make sure it is operable. Stove Does Not Burn Long 0 Depending upon wood, draft, and other factors, the Enough burn time may be shorter then stated. Make sure the doors are sealing and not allowing air into the firebox- See the section "Door and Glass Inspection" on page 28 for details. • Check the ash bed for coals. Often, coals are still glowing under a slight bed of fly ash. By raking these into a pile you can re-start your stove quickly. ©Travis Industries 100-01334 4131122 Maintaining Your Appliance 27 /A\ Failure to properly maintain and inspect your appliance may reduce the performance and life of the appliance, void your warranty, and create a fire hazard. /A\ Establish a routine for the fuel, wood burner and firing technique. Check daily for creosote build-up until experience shows how often you need to clean to be safe. Be aware that the hotter the fire the less creosote is deposited, and weekly cleaning may be necessary in mild weather even though monthly cleaning may be enough in the coldest months. Contact your local municipal or provincial fire authority for information on how to handle a chimney fire. Have a clearly understood plan to handle a chimney fire. Daily Maintenance (while stove is in use) Remove Ash (if necessary) Whenever ashes get 3 to 4 inches deep in your firebox or ash pan, and when the fire has burned down and cooled, remove excess ashes. Leave an ash bed approximately 1 inch deep on the firebox bottom to help maintain a hot charcoal bed. Let the stove cool completely before removing ashes (wait at least two hours after the last coal has extinguished). Ashes should be placed in a metal container with a tight-fitting lid. The closed container of ashes should be placed on a noncombustible floor or on the ground, away from all combustible materials, pending final disposal. The ashes should be retained in the closed container until all cinders have thoroughly cooled. • Ash removal is not required once it builds up. 1/2"to 1" of ash may be desirable because it slows the burn rate. Generally, remove ash once it has built up over 1". Follow the directions below to remove ash. 1 Let the stove cool completely (at least two hours after the last coal has extinguished). 2 Place a cloth or cardboard protector over the hearth to catch ash and protect against scratching. 3 Open the doors and scoop the ash into a metal container with a tight fitting lid. The closed container of ashes should be placed on a noncombustible floor or on the ASHES ground, away from all combustible materials, pending final disposal. /A\ Improperly disposed ashes lead to fires. Hot ashes placed in cardboard boxes, dumped in back yards, or stored in garages, are recipes for disaster. 0 Wood-burning stoves are inherently dirty. During cleaning have a vacuum ready to catch spilled ash U (make sure ash is entirely extinguished). 0 There are vacuum cleaners specifically made to remove ash (even if the ash is warm). Contact your dealer for details. Clean the Glass (if necessary) This appliance has an air wash to keep the glass clean. However, burning un-seasoned wood or burning on lower burn rates leads to dirtier glass All°w'he stove t°fully cool.Apply glass cleaner or soapy water to the inside of (especially on the sides). Clean the glass by the paper Wipe w""newspaper era paper towel. following the directions below. Do not clean glass with abrasive cleaners. For Stubborn Creosote: \ Dip newspaper or a paper towel in cool ashes and wipe it on the glass.The ash acts as a light abrasive. UThe glass will develop a very slight haze over time. This is normal and will not affect viewing of the fire. ©Travis Industries 100-01334 4131122 i Maintaining YourAppliance Monthly Maintenance (while appliance is in use) /A\ Make sure the appliance has fully cooled prior to conducting service. Door and Glass Inspection The door must form an air-tight seal to the firebox for the stove to work correctly. Inspect the door gasket to make sure it forms an air-tight seal to the firebox. 0 The door can be lifted off the hinges if extensive repairs are conducted. High-Temperature anti-sieze • Use wood stove gasket \ may be used on the door y cement to re-adhere hinges to eliminate squeaks. . • loose gasket. If the glass is damaged,replace • • Severely frayed or thread-bare it-see"Replacement Parts"for E gasket should be replaced. details. • • • The door latch should pull the door against the face of the stove (but not so tight as to not allow full handle rotation). If the latch requires adjustment, follow the directions below. Side View of Door Handle Exploded View Door Cam Door Handle ••Door Cam Adjustment: To tighten,remove Washers a washerfrom the inside of the door frame. To loosen, Use a 9/16" place an additional Door Frame socket wrench to washers on the remove this nut. inside of the door frame or loosen the nut 1/2 turn. Creosote - Formation and Need for Removal When wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moisture to form creosote. The creosote vapors condense in the relatively cool chimney flue of a slow- burning fire. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote makes an extremely hot fire. The chimney and chimney connector should be inspected at least once every two months during the heating season to determine if a creosote buildup has occurred. If creosote has accumulated, it should be removed to reduce the risk of a chimney fire. /A\ If you are not certain of creosote inspection, contact your dealer or local chimney sweep for a full inspection. Excess creosote buildup may cause a chimney fire that may result in property damage, injury, or death. ©Travis Industries 100-01334 4131122 Maintaining Your Appliance 29 Yearly Maintenance /A\ Make sure the appliance has fully cooled prior hu conducting service. Touch-Up Paint Included with the owner's pack nf this appliance ksn can nfStove'8hte@ point. To touch up nicks or dulled pnint, apply the paint while the appliance is cool. Sand rusted or damaged areas before preparation (use 120'ght Touch-Up sandpaper). Clean Wait' Paint hour before starting the appliance. The touched up area will appear darker than the surrounding paint until it cures from heat. Curing will give off some fumes while curing—open windows toventilate. Cleaning the Air Duct and Blower (if applicable) Use a vacuum to clean the air ducts (ohanne|a). This prevents dust from burning and creating odors. The optional blower should be vacuumed every year to remove any buildup of dust, lint, etc. BOTTOM OF Use a vacuum cleaner to remove any STOVE buildup on the screens of the blower. 00 Firebrick and Baffle Inspection Use the illustration on page 31 ana reference for checking the following items. Make sure the appliance ia cool before proceeding. Baffle Firebricks -check the bricks along the ceiling of the firebox to make sure they are intact and have nu gaps between them. Slide the bricks bo eliminate any gaps. Baffle Supports ' make sure the front and back baffle supports in are place and not degraded. Slight scaling or rusting of the metal is normal. Secondary Air Tubes - Check the two air tubes and collars to make sure they are intact and not severely deteriorated. Slight scaling or rusting of the metal ia normal. Make sure the push pins hold the air tubes in place. Floor and Wall Firebricks- replace any severely damaged firebrick along the side or floor of the firebox. @ Travis Industries 100'01334 4131122 30 Maintaining Your Appliance Door Parts 13 NOTE:Place the glass gasket around the perimeter of the door retainer. NOTE:Glue the door gasket 9/16"Wrench to the door retainer. ID# Description Qty Part# lD# Description Qty Part# Door Shell-Brass 230-00572 Door Shell-Pewter 230-00568 7 Door Handle Asbly-Black 1 224-14042 8 Door Handle Spring-Black 1 250-00372 Door Handle Asbly-Brass 99900410 Door Handle Spring-Brass 250-00591 1 Door Handle Asbly-Pewter 224-14052 1 Door Handle Spring-Pewter 250-00365 Replacing the Glass /A\ The glass must not contact the door retainer or glass clips directly. The glass gasket and glass clip gaskets insulate the glass hy prevent cracking. Do not over-tighten the glass clips. See "Door Shell Installation" (pg. 35)for details on removing the door handle and shell. NOTE: The glass gasket is placed in the grove along the inside perimeter of the door retainer. Make sure the glass clip screws are all fully tightened -they must be flush with the door retainer for the door shell to install. Replacing the Door Gasket The door gasket inserts into the outer groove nf the door retainer. Stove gasket cement holds itinplace. Before installing, remove any residual cement. Lay the gasket in place (start at the lower left corner) and cut off any excess gasket(do not stretch the gasket. The cement fully cures with heat from the stove. You may need to open and close the door repeatedly to get the gasket to seat fully. Replacing the Door Handle See the illustration above for a component list (see pg. 28 for details on adjusting the door). @ Travis Industries 100'01334 4131122 Maintaining Your Appliance 31 Firebox Parts 1 6 9 7 6 O O 11 1 r 5 11 11 4% 4 11 11 12 11 11 11 11 13 11 11 13 ID# Description Oty Part# ID# Description Qty Part# 1 Air Tubes&Sleeve 1 98900233 2 Air Tube Roll Pins 6 98900357 3 Air Tube Retainer Sleeve 3 250-00042 4 Baffle Support,Front 1 99900251 5 Baffle Support, Rear 1 99900250 6 Damper Plate 1 98900322 7 Damper Slider 1 98900342 8 Gasket,Damper Plate 1 91001701 9 Damper Yoke 1 98900325 10 Damper Extension Rod 1 98900332 with Pull Ring 11 Brick-9"x 4.5"un-cut 1 18 251-00000 1 1 12 1 Brick,Cut—9"x 2.125" 2 251-00055 13 Brick,Cut—9"x 3.687 1 4 251-00022 Floor and Side Firebrick Removal & Replacement Do not pry firebrick -they chip and crack easily. Remove the floor firebricks first. The side firebricks are removed later because they are pinned in place by the floor firebrick. Clean the firebox prior to replacing the firebrick. ©Travis Industries 100-01334 4131122 Maintaining32 YourAppliance Baffle Removal & Replacement 1 Push the front firebricks up and feed them forward, guiding them out the door. Repeat for the rear firebricks. Bypass Rod (&Yoke) Front Baffle Support Baffle Firebrick /Bypass Damper Front Air Tube ��Bypass Support -4'oo� O O o Bypass Gasket Support Tabs Center Baffle Support 2 The baffle supports rest on support tabs. 3 The bypass support and damper are difficult to remove and should only be removed if necessary. Remove the rear secondary air tube (see the following section for instructions). Slide the bypass support forward until the bypass rod can be disconnected from the bypass damper. Slide the damper forward and remove. The bypass support is removed by sliding it forward and rotating it downwards (the bypass holder fits very snug inside the firebox and is very heavy, making it difficult to remove). The bypass gasket rests on the side and rear air channels. Try not to damage it when removing the bypass holder. Air Tube Removal & Replacement Air Tube Collar Air Tube O Remove the left pin on the air tube collar � a 0 i 00 0 0 Roll Pin L ® Slide the air tube to the left, swing it 000 down and remove from the firebox. 0 00 ©Travis Industries 100-01334 4131122 Limited 7 Year Warranty 33 Register your TRAVIS INDUSTRIES,INC.Limited 7 Year Warranty online at traviswarrantv.com. TRAVIS INDUSTRIES,INC.warrants this gas appliance (appliance is defined as the equipment manufactured by Travis Industries,Inc.)to be defect-free in material and workmanship to the original purchaser from the date of purchase as follows: Check with your dealer in advance for any costs to you when arranging a warranty call. Mileage or service charges are not covered by this warranty.This charge can vary from store to store. Years 1 &2-COVERAGE:PARTS&LABOR Firebox Assembly: Ceramic Glass: Re-Installation Allowance: Firebox,Baffle Supports,Air Tubes,Air Channels,Convection Chamber Glass(breakage from thermal shock) In cases where heater must be removed from home for Door Assembly: Firebrick: repairs,a partial cost of re-installation is covered(pre- Solid Brass or Cast Door,Latch Assembly,Glass Retainers Breakage from thermal shock authorization required) Plated Finish Accessories: One-Way Freight Allowance: Plated Door,Legs,etc.See"Conditions&Exclusions"#9 below. Legs,Pedestal,Panels,Blower One-way freight allowance on pre-authorized repair Air Control Assembly: done at factory is covered. Slider Plate,Pressure Plate Exclusions: Paint,Gasketing Years 3 Through 5-COVERAGE: PARTS&LABOR Firebox Assembly: Door Assembly: One-Way Freight Allowance Firebox,Baffle Supports,Air Tubes,Air Channels,Convection Chamber Solid Brass or Cast Door,Latch One-way freight allowance on pre-authorized Air Control Assembly Assembly,Glass Retainers repair done at factory is covered. Slider Plate,Pressure Plate Exclusions: Paint,Gasketing,Plated Finish,Accessories(Legs,Pedestal,Panels,Blower),Glass,Firebrick,Re-Installation Allowance Years 6&7-COVERAGE:PARTS ONLY Firebox Assembly: Door Assembly: Air Control Assembly Firebox,Baffle Supports,Air Tubes,Air Channels,Convection Chamber Solid Brass or Cast Door,Latch Assembly,Glass Retainers Slider Plate,Pressure Plate Exclusions: Paint,Gasketing,Plated Finish,Accessories(Legs,Pedestal,Panels,Blower),Glass,Firebrick,Re-Installation Allowance,One- Way Freight Allowance,Labor CONDITIONS&EXCLUSIONS 1. This new appliance must be installed by a qualified installer. It must be installed,operated,and maintained at all times in accordance with the instructions in the Owner's Manual. Any alteration,willful abuse,accident,neglect,or misuse of the product shall nullify this warranty. 2. This warranty is nontransferable,and is made to the ORIGINAL purchaser,provided that the purchase was made through an authorized Travis dealer. 3. Discoloration and some minor expansion,contraction,or movement of certain parts and resulting noise,is normal and not a defect and,therefore,not covered under warranty. Over-firing(operation where the steel may glow red)of this appliance can cause serious damage and will nullify this warranty. 4. The warranty,as outlined within this document,does not apply to the chimney components or other Non-Travis accessories used in conjunction with the installation of this product.If in doubt as to the extent of this warranty,contact your authorized Travis retailer before installation. 5. Travis Industries will not be responsible for inadequate performance caused by environmental conditions such as nearby trees,buildings,roof tops,wind,hills or mountains or negative pressure or other influences from mechanical systems such as furnaces,fans,clothes dryers,etc. 6. This Warranty is void if: a. The unit has been operated in atmospheres contaminated by chlorine,fluorine or other damaging chemicals. b. The unit is subject to submersion in water or prolonged periods of dampness or condensation. c. Any damage to the unit,combustion chamber,heat exchanger or other components due to water,or weather damage which is the result of,but not limited to,improper chimney/venting installation. 7. Exclusions to this 7 Year Warranty include: injury,loss of use,damage,failure to function due to accident,negligence,misuse,improper installation,alteration or adjustment of the manufacturer's settings of components,lack of proper and regular maintenance,damage incurred while the appliance is in transit,alteration,or act of God. 8. This 7 Year warranty excludes damage caused by normal wear and tear,such as paint discoloration or chipping,worn or torn gasketing,chipped or cracked firebrick,etc. Also excluded is damage to the unit caused by abuse,improper installation,modification of the unit,or the use of fuel other than that for which the unit is configured(use cord wood only). 9. Damage to brass or plated surfaces caused by fingerprints,scratches,melted items,or other external sources left on the surfaces from the use of abrasive cleaners is not covered in this warranty. Damage to the surfaces from over-firing(operation where the steel may glow red)is not covered in this warranty. 10. TRAVIS INDUSTRIES,INC.is free of liability for any damages caused by the appliance,as well as inconvenience expenses and materials. Incidental or consequential damages are not covered by this warranty. In some states,the exclusion of incidental or consequential damage may not apply. 11. This warranty does not cover any loss or damage incurred by the use or removal of any component or apparatus to or from the Travis appliance without the express written permission of TRAVIS INDUSTRIES,INC. and bearing a TRAVIS INDUSTRIES,INC.label of approval. 12. Any statement or representation of Travis products and their performance contained in Travis advertising,packaging literature,or printed material is not part of this 7 year warranty. 13. This warranty is automatically voided if the appliance's serial number has been removed or altered in any way.If the appliance is used for commercial purposes, it is excluded from this warranty. 14. No dealer,distributor,or similar person has the authority to represent or warrant Travis products beyond the terms contained within this warranty. TRAVIS INDUSTRIES,INC.assumes no liability for such warranties or representations. 15. Travis Industries will not cover the cost of the removal or re-installation of hearths,facing,mantels,venting or other components. 16. If for any reason any section of this warranty is declared invalid,the balance of the warranty remains in effect and all other clauses shall remain in effect. 17. This 7 year warranty is the only warranty supplied by Travis Industries,Inc.,the manufacturer of the appliance. All other warranties,whether express or implied, are hereby expressly disclaimed and purchaser's recourse is expressly limited to the warranties set forth herein. IF WARRANTY SERVICE IS NEEDED: 1. If you discover a problem that you believe is covered by this warranty,you MUST REPORT it to your Travis dealer WITHIN 30 DAYS,giving them proof of purchase,the purchase date,and the model name and serial number. 2. Travis Industries has the option of either repairing or replacing the defective component. 3. If your dealer is unable to repair your appliance's defect,he may process a warranty claim through TRAVIS INDUSTRIES,INC.,including the name of the dealership where you purchased the appliance,a copy of your receipt showing the date of the appliance's purchase,and the serial number on your appliance. At that time,you may be asked to ship your appliance,freight charges prepaid,to TRAVIS INDUSTRIES,INC. TRAVIS INDUSTRIES,INC.,at its option,will repair or replace,free of charge,your appliance if it is found to be defective in material or workmanship within the time frame stated within this 7 year warranty. TRAVIS INDUSTRIES,INC.will return your appliance,freight charges(years 1 to 5)prepaid by TRAVIS INDUSTRIES,INC.,to your regional distributor,or dealership. 4. Check with your dealer in advance for any costs to you when arranging a warranty call. Mileage or service charges are not covered by this warranty.This charge can vary from store to store. ©Travis Industries 100-01334 4131122 34 Listing Label Listing Label DO NOT REMOVE THIS LABEL CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT INSTALLATION AND RESTRICTIONS IN YOUR AREA. SUITABLE FOR USE IN CONVENTIONAL RESIDENTIAL INSTALLATIONS,MANUFACTURED HOMES AND ALCOVES. MODEL: SERIAL NO: c 1 I us Intertek •, ENDEAVOR FR Report No.B0508PRT-001 Certified for USA and Canada Control No.4000515 CONFORMS TO UL STD 1482;CERTIFIED TO ULC STD S627.2000 PREVENT HOUSE FIRES-Install and use only in accordance with the manufacturer's installation and operating instructions.Contact your local building or fire officials about restrictions and installation inspection in your area.Refer to local building codes and manufacturer's instructions for precautions required for passing a chimney through a combustible wall or ceiling.Do not run a chimney connector through a combustible wall or ceiling.Do not connect this unit to a chimney flue serving another appliance.Clearances may be reduced by methods specified in NFPA 211, listed wall shields,pipe shields,or other means approved by local building or fire officials. FREESTANDING INSTALLATION STANDARD RESIDENTIAL FREESTANDING INSTALLATIONS REQUIRE:6"diameter,minimum 24 MSG black,with listed UL-103 HT factory-built chimney,suitable for use with solid fuels or masonry chimney.Pedestal or legs are required. ALCOVE INSTALLATIONS REQUIRE:One of the Listed doublewall connectors listed below.Pedestal or legs are required. MANUFACTURED HOME AND REDUCED CLEARANCE INSTALLATIONS REQUIRE:One of the Listed doublewall connectors listed below.In addition,manufactured home installations require outside air-use the optional pedestal or outside air boot. •AMERI-TEC model DCC connector with model HS chimney •METALFAB model DW connector with TG chimney •DURA-VENT model DVL connector with DURA-PLUS chimney •OLIVER MACLEOD PROVENT model PV connector with model 3103 chimney •GSW-JAKES EVANS SUPERPIPE 2100 •SECURITY model DP connector with SECURITY model ASHT or S2100 chimney •I.C.C.EXCEL(103-HT)chimney with HP connector •SELKIRK METALBESTOS model DS connector with model SSII chimney •OLYMPIA VENTISO with Ventis doublewall black stove pipe Minimum Clearances Singlewall Connector Alcove,Manufactured Home and Reduced To Combustibles And Conventional Residential Clearance Conventional Residential Hearth Requirements: Installations Installations A. 15 in.1381 mm 13 in.1331 mm B. 15 in.1381 mm 4.25 in.1108 mm C. 15 in.1381 mm 6.5 in.1166 mm D. 24 in.1610 mm 21.5 in.1547 mm E. 17.75 in.1451 mm 6.5 in.1166 mm F. 24 in.1610 mm 15 in.1381 mm G. US:6 in.(153 mm)I CAN:8 in.(204 mm) US:6 in.(153 mm)1 CAN:8 in.(204 mm) H. US:16 in.(407 mm)1 CAN:18 in.(458 mm) US:16 in.(407 mm)1 CAN:18 in.(458 mm) FREESTANDING CLEARANCE DIAGRAM ALCOVE SPECIFICATIONS FLOOR PROTECTION DIAGRAM BACKWALL ADJACENT WALL FLOOR PROTECTOR Floor protection must be a non-combustible TE , t � Max.Alcove Depth: 48 in.(1220 mm) material extending beneath the heater and to 45° the front,sides and back as indicated.See D Min.Alcove Height: See Owner'sManual\ s O Owner's Manual for examples of non-com- s A TOLD C n Min.Alcove Width: See Owner's Manual H FRONT bustible materials that can be used. Do not obstruct space beneath heater. Electrical Rating: 115V.,60 Hz,1.8 Amps Manufactured by: Optional Blower: #99000138 TRAVIS INDUSTRIES,INC. Do not route power cord under or in front of appliance. TM 12521 Harbour Reach Drive Replace glass only with 5mm neoceramic or T R A V I S INDUSTRIES Mukilteo,WA 98275 ceramic glass. HOUSE OF FIRE www.travisproducts.com U.S.ENVIRONMENTAL PROTECTION AGENCY Certified to comply with 2015 particulate emission standards.Not approved for sale after May 15,2020.1.9 g1h,Method 28,5H,2015 DATE OF MANUFACTURE 2015 2016 2017 2018 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Made in U.S.A. ■ ■ ■ ■ ■ ■ ■ ■ ■ 0905 ©Travis Industries 100-01334 4131122 35 Optional Equipment Door Shell Installation 1. Remove the door retainer shipping latch following the directions below. e Sderd Sc do e 41 Rotate this shaft 1/4 turn clockwise until the door unlatches. Swing the door retianer open. Remove and discard the shipping latch and nut. Shipping Latch j Door Retainer 9/16"Wrench 2. Place the door shell face down on a non-scratching surface. NOTE: On older door shell kits, the two set screws pre-installed on the bottom of the door shell may be discarded. Nickel (Cast Iron) Doors Only Use a socket-head wrench with 5/16"socket to pre-thread the holes 6 revolutions. If you pre-thread move revolutions, it may bottom out and break the head off the screw. Remove and retain the screws. See the photos below. i rr t ©Travis Industries 100-01334 4131122 36 Optional E • • 3. Place the door retainer into the door shell as shown below. Door Retainer Door Shell I I� " The indent on the door retainer slides into the clip on the door shell(on both sides). 4. Make sure the holes in the retainer line up with the holes on the shell then use a 5/16" nutdriver to secure the shell with the two screws. Tighten until the door shell is snug against the retainer(do not over-tighten). WARNING: Do not use a power drill or driver to attach the screws. The castings must be properly threaded and not stripped. O 5/16" Nutdriver 7 h ©Travis Industries 100-01334 4131122 37 Optional Equipment 5. Attach the door handle following the directions to the right. 6. Replace the door on the hinges and latch the door. o 0 9/16"Wrench � 6 Stove Leg Installation Part Numbers: Brass#99200500, Cast Black#99200800, Sculptured Steel#99200105 • Raise the stove 8" (use lumber). Attach each leg following the instructions below. Attach each leg to the stove by inserting a bolt and washer through the o hole or slot in the leg and into the threaded hole on the stove. 9/16"Socket Wrench These rubber-tipped bolts are for leveling the stove Make sure they contact the floor. Do not adjust with weight on the legs,the rubber tips may tear. ©Travis Industries 100-01334 4131122 38 Optional E • • Pedestal (Part # 99200106) �AM� If using outside air with the pedestal, follow the directions below under"Using Outside Air with the Pedestal" prior to installing the pedestal. Optional Air Intake Port Attachment Bolts and If installing in a mobile home, Washers-use a 9/16" insert the lag bolts through socket wrench to --o these holes and screw them attach the pedestal to I into the floor with a 1/2"socket the stove. wrench. 22" When attached,the face of the 23 5/8" �- stove is 2 1/2"in front of the front edge of the pedestal. OUTSIDE AIR EQUIPMENT(wood stoves only) Insulation is Staples are used to attach The cover plate Screen is used used to seal the the screen to the floor. may be discarded. to prevent side edges of rodents from O the pedestal. entering. Using Outside Air with the Pedestal Before installing, check the section "Outside Air Requirements" 12 for installation concerns. 1. Determine the location of the outside air hole penetrating the floor(& hearth). The illustration above details the size of pedestal and its location in relation to the stove. The hole may be cut anywhere underneath the pedestal, as long as it is not within 2"of the outside perimeter of the pedestal, is at least 16 square inches in area, and does not interfere with structural members of the home. Place the rodent screen over the hole (above or below) and secure with staples. 2. Attach the stove to the pedestal with the included bolts. Tuck the included insulation underneath the side edges of pedestal to seal off any air from entering underneath the pedestal. ©Travis Industries 100-01334 4131122 • Optional Equipment Outside Air Boot Installation (Part number 99200134) The outside air boot routes outside air to the stove for combustion. Refer to the section "Outside Air Requirements"for installation concerns. The directions below detail installation. 1 Install the cover plate following the directions below (use the cover plate that is 6-1/2"wide). The cover plate prevents combustion air from entering the front of the stove. Remove the two screws on the o cover plate to remove the piece that fits over the air control rod. Then replace the piece when the cover 11 V I Air Control Rod i 1s plate is in place. The cover plate has a clip which attaches o Li��Z/ it underneath the air control. 2 Refer to the illustration below to determine the location and size of the hole penetrating the floor and hearth. The knock-out(which is pre-removed) is 6-3/8" behind the face of the stove - it is 8" wide and 4-1/4" deep. Cut the hole prior to locating the stove. 3 Attach gasket to the bottom edge of the lower air boot section (near the screen). Attach gasket on top of the flanges on the upper air boot section. Slide the two sections together with both seams facing the rear(do not attach the two sections at this time). 4 Follow the directions below for attaching the upper section of the air boot (with gasket)to the stove. 5 Slide the lower section down until it contacts the hearth. Attach the two sections together following the directions below Use a Bottom of Stove screwdriver to pry out the Attach the included knock-out. gasket to all four top edges of the air boot. I 0 /7 Attach the air boot with the two screws included with the kit. 1/4"Nutdriver Use the included screws to attach the two telescoping portions of air / boot together. The included drill bit should be used to drill the hole. Make sure the air boot is expanded Attach gasket to the bottom to the correct size before drilling. ///�// edge of the air boot. 1� ® �I � 9/64"Drill Bit 5/16"Nutdriver The hole in the floor(and hearth) must be a minimum 16 square V inches. It should be smaller than the footprint of thehe air air boot in Floor(and hearth) each dimension to allow for the gasket to seal. Adjusting the Burn Rate...................................21 Air Tube Removal & Replacement..................32 ©Travis Industries 100-01334 4131122 T _ Alcove Installation Requirements.....................13 Interior or Exterior Masonry Chimney..............17 Baffle Removal & Replacement.......................32 Introduction ........................................................2 Before Your First Fire.......................................18 Listing Label.....................................................34 Bypass Operation.............................................19 Mobile Home Requirements............................14 Cathedral Ceiling with a Factory Built Chimney Monthly Maintenance.......................................28 ......................................................................15 Normal Operating Sounds...............................23 Chimney Connector Requirements..................10 Opening the Door.............................................19 Chimney Requirements....................................11 Optional Blower Operation...............................23 Chimney Termination Requirements ...............12 Outside Air Boot Installation ............................39 Clean the Glass................................................27 Outside Air Requirements................................12 Cleaning the Air Duct and Blower....................29 Over-Firing the Stove.......................................18 Clearances.........................................................8 Packing List........................................................7 Creosote - Formation and Need for Removal..28 Pedestal...........................................................38 Curing the Paint ...............................................18 Planning The Installation ...................................7 Daily Maintenance............................................27 Re-Loading the Stove......................................23 Dimensions ........................................................6 Remove Ash ....................................................27 Do Not Burn List...............................................25 Replacing the Door Gasket..............................30 Door and Glass Inspection...............................28 Replacing the Door Handle..............................30 Door Parts........................................................30 Replacing the Glass.........................................30 Door Shell Installation ......................................35 Safety Notice....................................................18 Emissions...........................................................6 Selecting Wood................................................24 Exterior Factory Built Chimney ........................16 Standard Ceiling with a Factory Built Chimney 15 Features.............................................................6 Starting a Fire ..................................................20 Firebox Parts....................................................31 Stove Installation Considerations ......................7 Firebrick and Baffle Inspection.........................29 Stove Leg Installation ......................................37 Floor and Side Firebrick Removal & Stove Placement Requirements........................8 Replacement ................................................31 TopView...........................................................9 Floor Protection Requirements ..........................8 Touch-Up Paint................................................29 Hearth Stove Direct Connection ......................17 Troubleshooting 26 Hearth Stove Positive Connection ...................16 Using Outside Air with the Pedestal ................38 Heating Specifications........................................6 WhyDr Wood is Key 24 Hints for Burning24 Y Y...................................... .............................................. Wood Cutting and Storage ..............................24 Important Information.........................................2 Yearly Maintenance.........................................29 Installation Options.............................................6 ©Travis Industries 100-01334 4131122 RESIDENTIAL MECHANICAL PERMIT APPLICATION t�N Department of Community & Economic Development City of Arlington • 18204 59th Ave NE • Arlington, WA 98223 • Phone (360) 403-3551 THIS APPLICATION IS TO BE USED WHEN APPLYING FOR NEW MECHANICAL INSTALLATION AND OR GAS PIPING FOR EXISTING RESIDENCES. PLEASE FILL OUT ALL PAGES OF THIS APPLICATION AND INCLUDE ALL INFORMATION. Project Address- 19721 47th Ave NE Project Description:install free standing wood stove and venting Owner: Chris Cluer Address. 19721 47th Ave NE City. Arlington State.WA Zip Code: 98223 Phone. 425-802-4724 Email:nlcluer@gmail.com Applicant: Ben Sousa/Craft Stove Address: 900 W Division City. Mount Vernon State.WA Zip Code: 98273 Phone. 360-336-2532 Email: craftstoveswash@comcast.net CONTRACTOR INFORMATION Contractor Name:Craft Stove Installation Address: 900 W Division City. Mount Vernon State.WA Zip Code: 98273 License Number:craftsi831ch Expiration. 8/31/19 Phone: 360-336-2532 Email:craftstoveswash@comcast.net STAFF USE ONLY Permit #: Accepted by: Date: 6/16LP Page 1 of 2 Y. RESIDENTIAL MECHANICAL PERMIT APPLICATION SING Department of Community& Economic Development City of Arlington • 18204 59th Ave NE• Arlington, WA 98223• Phone(360) 403-3551 SELECT ALL PROPOSED APPLIANCES ❑ Furnace (80+) Model # AFUE ❑ Heat Pump Model # AFUE HSPE ❑ AC Unit Model # SEER l� Freestanding Stove ❑ Fire Place Insert ❑ Outdoor BBQ ❑ Gas Piping ❑ Solid-Fuel Appliance ❑ Other Gas Piping Information Not Applicable: l� Pipe Material: Pipe Size: Distance from Meter to Furthest Appliance: Total BTU's of all Appliances: • New gas piping requires a pressure test hooking to any appliance • Sediment traps (drips) are required on all gas lines • Gas lines are required to be supported/secured every 6 to 8 feet • Proper Combustion air and venting required for all appliances • A shut-off valve is required within 6 feet of all appliances Applicant Signature: d5a513be"a92O�tlb81'e`1e6' Date: 09/10/2018 Applicant Printed Name: Dawn Sousa Birch I hereby certify that the above information is correct and that the construction, installation for the above mentioned property will be in accordance with the applicable laws of the City of Arlington and the State of Washington. 6/16LP Page 2 of 2 i mxCITY OF ARLINGTON J 238 N. OLYMPIC AVE-ARLINGTON,WA. 98223 PHONE; (360)403-3551 BUILDING`PERi�QT Address:19721 47th Avenue NE Permit#:2172 Parcel M 00564600000401 Valuation:0.00 - --- W1ER_ APPLICANT. CONTRLC 'QR Name:CLUER CHRISTOPHER Name:Craft Stove Name:CRAFT STOVE INSTALLATIONS Address: 1972147TH AVENUE NE Address:900 W Division Address:900 W DIVISION City,State Zip:ARLINGTON,WA 98223 City,State Zip:Mount Vernon,WA 98273 City,State Zip:MOUNT VERNON,WA 98273 Phone: Phone:360-336-2532 Phone:360-336-2532 _ -._-•... v_.._.._ - y�1�^1 _ - Name:CRAFT STOVE INSTALLATIONS Name: i Address:900 W DIVISION Address: E City,State,Zip:MOUNT VERNON,WA 98273 City,State,Zip: Plione:360-336-2532 Phone: € LIC M EXP: LIC#: EXP: JOB bFSRiPTION. . _ __ PERMIT TYPE: Residential Mechanical CODE YEAR: 2015 STORIES: CONST.TYPE: DWELLING UNITS: 1 OCC GROUP: BUILDINGS: I OCC LOAD: MWT APPROVAL IIAGREE TO COMPLY WITH CITY AND STATE LAWS REGULATING CONSTRUCTION AND IN DOING THE WORK AUTHORIZED THEREBY, NO PERSON WILL BE EMPLOYED IN VIOLATION OF THE LABOR CODE OF THE STATE OF WASHINGTON RELATING TO WORKMEN'S COMPENSATION INSURANCE AND RCW 18.27. THIS APPLICATION IS NOT A PERMIT UNTIL SIGNED BY THE BUILDING OFFICIAL OR HIS/HER DEPUTY AND ALL FEES ARE PAID, E € IT IS UNLAWFUL TO USE OR OCCUPY A BUILDING OR STRUCTURE UNTIL A FINAL INSPECTION HAS BEEN MADE AND APPROVAL OR s A CERTIFICATE OF OCCUPANCY HAS BEEN GRANTED. IBC 110/IRC 110. t SAL,EE4 TAX NOTICE:Sales tax jp ting to construction and construction m:derials in the City of ArN • tttt a reported on your sales tax returnAirnt and IArlington#31 1 Signature Print Name Date Released By t D41 INSTALL PER MANUFACTURER'S INSTALLATION SPECIFICATIONS, THIS PERMITAUTHORI7S ONLY THE WORK NOTED,THIS PERMIT COVERS WORK TO BE DONE ON PRIVATE.PROPERrY ONLY. ANY CONSTRUCTION ON THE PUBLIC DOMAIN(CURBS,SIDEWALKS,DRIVEWAYS,MARQUEES,ETC.)WILL REQUIRE SEPARATE PERMISSION. f Date Description- Fee Amount 9/24/2018 Mechanical Fee(Enter Fixture Fee) $25.00 9/24/2018 Mechanical Permit Base Fee $25.00 9/24/2018 Processing/Technology Fee $25.00 Total Due: $75.00 r Total Payment: $0,00 1 Balance Due: $75.00 I CA�;`F4R:INSp��"I'IONS• ..,.::. :. BUILDING(360)403-3417 k 1 When calling for an inspection please leave the following information: f Permit Number,Type of Inspection being requested,and whether you prefer morning or afternoon 1 i I ` ITS( OF ARLINGTON 238 N. OLYMPIC AVE-ARLINGTON,WA. 98223 - PHONE; (360)403-3551 _ BL9Wj.N;G'PER.MIT i Address: 11721 47th Avenue NE Permit#:2172 Parcel#:00564600000401 Valuation:0.00 OWNER APPLICANT CONTRACTOR Name:CLUER CHMISTOPEER Name:Craft Stove Name:CRAFT STOVE INSTALLATIONS Address: 19721 41TH AVENUE NE Address:900 W Division Address:900 W DIVISION City,State Zip:ARLINGTON,WA 98223 City,State Zip:Mount Vernon,WA 98273 City,State zip:MOUNT VERNON,WA 98273 Phone: Phone:360-336-2532 Phone:360-336-2532 MECHANICAL CONTRACTOR PL,UN*1NG CONTRA Name:CRAFT STOVE INSTALLATIONS Name: Address:900 W DIVISION Address: City,State,Zip:MOUNT VERNON,WA 98273 City,State,Zip: Phone:360-336-2532 Phone: LIC#: EXP: LIC#: EXP: JOB:DESGItI�'ION _ :. _- PERMIT TYPE: Residetltial Mechanical CODE YEAR: 2015 STORIES: CONST.TYPE: DWELLING UNITS: I OCC GROUP: BUILDINGS: 1 OCC LOAD: PERNiIT:APIMMAL:..._ I AGRER TO COMPLY WITH(.TTY AND STATE LAWS RF.GIJLATING CONSTRUCTION AND IN DOING THE WORK AUTHORIZED THEREBY; NO PERSON WILL BE EMPLOYED IN VIOLATION OF THE LABOR CODE OF THE STATE OF WASHINGTON RELATING TO WORKMEN'S COMPENSATION INSURANCE AND RCW 18.27. THIS APPLICATION IS NOT A PERMIT UNTIL SIGNED BY THE BUILDING OFFICIAL OR HIS/HER DEPUTY AND ALL FEES ARE PAID. IT IS UNLAWFUL TO USE OR OCCUPY A BUILDING OR STRUCTURE UNTIL A FINAL INSPECTION HAS BEEN MADE AND APPROVAL OR A CERTIFICATE OF OCCUPANCY HAS BEEN GRANTED, IBCI IOARCI IO. SALES TAX NOTICE:Sa1"lax #ating to construction and construction materials in the City ofAri6clo, nit a repotted on your sales tax return.ronn and d Arlington 01liq ar Signature Print Name Data Releused By bat - CONDITIONS - INSTALL PER MANUFACTURER'S INSTALLATION SPECIFICATIONS. THIS PERMIT AUTIIORIZS ONLY THE WORK NOTED,THIS PERMIT COVERS WORK TO BE DONE ON PRIVATE PROPERTY ONLY. ANY CONSTRUCTION ON THE PUBLIC DOMAIN(CURBS,SIDEWALKS,DRIVEWAYS,MARQUEES,ETC.)WILL REQUIRE SEPARAfF PERMISSION. _ . PER_ MXTFNES Date Description _ W Fea Amount 9/24/2018 Mechanical Fee(Enter Fixture Fee) $25.00 ' 9/24/2018 Mechanical Permit Base Fee $25.00 9/24/2018 Processing/Technology Fee $25.00 I Total Due: $75.00 Total Payment: $0.00 Balance Due: $75.00 I I CALUVOR-INSPECTIONS ` BUILDING(360)403-3417 When calling for an Inspection please leave the following information: Permit Number,Type of Inspection being requested,and whether you prefer morning or afternoon I S GITY OF ARLINGTON 238 N. OLYMPIC AVE - ARLINGTON, WA. 98223 ` PHONE; (360)403-3551 BUILDING PERMIT Address:19721 47th Avenue NE Permit#:2172 Parcel#:00564600000401 Valuation:0.00 OWNER APPLICANT CONTRACTOR Name:CLUER CHRISTOPHER Name:Craft Stove Name:CRAFT STOVE INSTALLATIONS Address: 19721 47TH AVENUE NE Address:900 W Division Address:900 W DIVISION City,State Zip:ARLINGTON,WA 98223 City,State Zip:Mount Vernon,WA 98273 City,State Zip:MOUNT VERNON,WA 98273 Phone: Phone:360-336-2532 Phone:360-336-2532 MECHANICAL CONTRACTOR PLUMBING CONTRACTOR Name:CRAFT STOVE INSTALLATIONS Name: Address:900 W DIVISION Address: City,State,Zip:MOUNT VERNON,WA 98273 City,State,Zip: Phone:360-336-2532 Phone: LIC#: EXP: LIC#: EXP: JOB DESCRIPTION PERMIT TYPE: Residential Mechanical CODE YEAR: 2015 STORIES: CONST.TYPE: DWELLING UNITS: I OCC GROUP: BUILDINGS: 1 OCC LOAD: PERMIT APPROVAL I AGREE TO COMPLY WITH CITY AND STATE LAWS REGULATING CONSTRUCTION AND IN DOING THE WORK AUTHORIZED THEREBY, NO PERSON WILL BE EMPLOYED IN VIOLATION OF THE LABOR CODE OF THE STATE OF WASHINGTON RELATING TO WORKMEN'S COMPENSATION INSURANCE AND RCW 18.27. THIS APPLICATION IS NOT A PERMIT UNTIL SIGNED BY THE BUILDING OFFICIAL OR HIS/HER DEPUTY AND ALL FEES ARE PAID. IT IS UNLAWFUL TO USE OR OCCUPY A BUILDING OR STRUCTURE UNTIL A FINAL INSPECTION HAS BEEN MADE AND APPROVAL OR A CERTIFICATE OF OCCUPANCY HAS BEEN GRANTED. IBC110/IRC110. SALES TAX NOTICE:Sales tax relating to construction and construction materials in the City of Arlu m e reported on your sales tax return form and coded City of Arlington#3101. /g Signature Print Name Date Released By L Dat CONDITIONS INSTALL PER MANUFACTURER'S INSTALLATION SPECIFICATIONS. THIS PERMIT AUTHORIZE ONLY THE WORK NOTED.THIS PERMIT COVERS WORK TO BE DONE ON PRIVATE PROPERTY ONLY. ANY CONSTRUCTION ON THE PUBLIC DOMAIN(CURBS,SIDEWALKS,DRIVEWAYS,MARQUEES,ETC.)WILL REQUIRE SEPARATE PERMISSION. PERMIT FEES Date Description Fee Amount 9/24/2018 Mechanical Fee(Enter Fixture Fee) $25.00 9/24/2018 Mechanical Permit Base Fee $25.00 9/24/2018 Processing/Technology Fee $25.00 Total Due: $75.00 Total Payment: $0.00 Balance Due: $75.00 CALL FOR INSPECTIONS BUILDING(360)403-3417 When calling for an inspection please leave the following information: Permit Number,Type of Inspection being requested,and whether you prefer morning or afternoon Permit Information Date 9/24/2018 Permit Number 2172 Project Name Cluer Applicant Name Craft Stove Applicant Address 900 W Division City,State,Zip Mount Vernon,WA 98273 Contact Dawn Sousa Birch Phone 360-336-2532 Email craftstovewash@comcast.net Permit Type Residential Mechanical Site Address 19721 47th Avenue NE Valuation 0.00 Status Applied Permit Issued Permit Expires Square Feet 0 Type of Construction/Occupancy Load Number of Stories 0 Proposed Use Install free standing wood stove Assigned To Launa Peterson Property Parcel Address Subdivision Lot Owner 00564600000401 19721 47TH AVE NE 1 CLUER CHRISTOPHER Contractors Contractor Name Primary Contact Phone Email Contractor Type License License# "RAFT STOVE INSTALLATIONS 160-336-2532 1 K',ONTRACTOR Labor&Industries ]RAFTSI831CH Review Date Tvoe Description I Target Date Completed DateI Assigned To Status 9/24/2018 lResidential Mechanical 10/1/2018 jBuildin n Review Fees Fee Description Notes Amount Mechanical Fee(Enter Fixture Feel 322.10.00.00 $25.00 Mechanical Permit Base Fee 322.10.00.00 $25.00 Processing/Technology Fee 341.43.00.02 $25.00 Total $75.00 Uploaded Files L Upload File 1 Date File U loaded B 9124/2018 2:14:09 PM 119721 attachme --015031000017664943 cgUv1Sg6SH6WN3u4uX 00 01334.pdf lPeterson, Launa I x 9/24/2018 2:14:09 PM 119721 Residential Mechanical DSGcVLPVwpY7SV.pdf I Peterson,Launa h RESIDENTIAL MECHANICAL PERMIT APPLICATION Department of Community& Economic Development City of Arlington • 18204 59th Ave NE• Arlington, WA 98223• Phone(360) 403-3551 THIS APPLICATION IS TO BE USED WHEN APPLYING FOR NEW MECHANICAL INSTALLATION AND OR GAS PIPING FOR EXISTING RESIDENCES. PLEASE FILL OUT ALL PAGES OF THIS APPLICATION AND INCLUDE ALL INFORMATION. Project Address:19721 47th Ave NE Project Description:install free standing wood stove and venting Owner: Chris Cluer Address: 19721 47th Ave NE City:Arlington State'.WA Zip Code: 98223 Phone: 425-802-4724 Email:nlcluer@gmail.com Applicant: Ben Sousa/Craft Stove Address:900 W Division City: Mount Vernon State WA Zip Code: 98273 Phone: 360-336-2532 Email: craftstoveswash@comcast.net CONTRACTOR INFORMATION Contractor Name:Craft Stove Installation Address: 900 W Division City: Mount Vernon _ State.WA Zip Code: 98273 License Number:craftsi831ch Expiration: 8/31/19 Phone:360-336-2532 Email:craftstoveswash@comcast.net i STAFF USE ONLY Received Permit#: Accepted by: e: 6/16LP Page 1 of 2 RESIDENTIAL MECHANICAL PERMIT APPLICATION Department of Community & Economic Development City of Arlington • 18204 59th Ave NE• Arlington,WA 98223• Phone(360) 403-3551 SELECT ALL PROPOSED APPLIANCES ❑ Furnace (80+) Model # AFUE ❑ Heat Pump Model # AFUE HSPE ❑ AC Unit Model # SEER (� Freestanding Stove ❑ Fire Place Insert ❑ Outdoor BBQ ❑ Gas Piping ❑ Solid-Fuel Appliance ❑ Other Gas Piping Information Not Applicable: 16 Pipe Material: Pipe Size: Distance from Meter to Furthest Appliance: Total BTU's of all Appliances: • New gas piping requires a pressure test hooking to any appliance • Sediment traps (drips) are required on all gas lines • Gas lines are required to be supported/secured every 6 to 8 feet • Proper Combustion air and venting required for all appliances • A shut-off valve is required within 6 feet of all appliances �aK.v6 tisori•�.�a�u t dt Applicant Signature: - Date:. 09i10i2018 Applicant Printed Name: Dawn Sousa Birch I hereby certify that the above information is correct and that the construction, installation for the above mentioned property will be in accordance with the applicable laws of the City of Arlington and the State of Washington. 6/16LP Page 2 of 2 • Endeavor i Wood Stove • - Owner's Manual • Freestanding Stove • Mobile-Home Approved • Alcove Approved • Hearth-Stove Approved Save these instructions for future reference AWARNING HOT GLASS WILL CAUSE BURNS. DO NOT TOUCH GLASS UNTIL COOLED. NEVER ALLOW CHILDREN TO TOUCH GLASS. SAFETY NOTICE: If this appliance is not properly installed, a house fire may result For your safety, follow the installation directions. Contact local building or fire officials about restrictions and installation inspection requirements in your area. ©Copyright 2015, T.I. ,3TM $10.00 100-01334 C TUs Listed lbRO TRAVIS INDUSTRIES 4131122 Intertek HOUSE OF FIRE Tested to: ULC 1482, ULC S627, &ULC S628 Receivea SEP 0 6 2018 - 2 Introduction Introduction We welcome you as a new owner of a Lopi Endeavor wood-burning stove. In purchasing a Lopi Endeavor you have joined the growing ranks of concerned individuals whose selection of an energy system reflects both a concern for the environment and aesthetics. The Lopi Endeavor is one of the finest appliances the world over. This manual will explain the installation, operation, and maintenance of this appliance. Please familiarize yourself with the Owner's Manual before operating your appliance and save the manual for future reference. Included are helpful hints and suggestions which will make the installation and operation of your new appliance an easier and more enjoyable experience. We offer our continual support and guidance to help you achieve the maximum benefit and enjoyment from your appliance. Important Information No other Lopi Endeavor appliance has the same serial number as yours. The serial number is stamped onto Register your warranty online at: the label on the back of the appliance. traviswarranty.com This serial number will be needed in case you require Save Your Bill of Sale. service of any type. To receive full warranty coverage,you will need to Model: Looi Endeavor ND show evidence of the date you purchased your heater. We suggest that you attach your Bill of Sale to this Serial Number: page so that you will have all the information you need in one place should the need for service or information Purchase Date: occur. Purchased From NATIONAL We suggest that our woodburning hearth FIREPLACE INSTITUTE' products be installed and serviced by professionals who are certified in the U.S. by the National Fireplace Institute® (NFI) as :Eml NFI Woodburning Specialists or who are certified in Canada by d CERTIFIED Wood Energy Technical X3WoodEnergy Technical Training wwn6certffied,uig Training (WETT). - 0 Travis Industries 100-01334 4131122 Safety Precautions 3 Introduction.......................................................2 Understanding Your Heater's Combustion Important Information......................................2 System............................................................22 Installation Options..........................................6 Burning Your Heater......................................22 Features ............................................................6 Optional Blower Operation ...........................23 Heating Specifications.....................................6 Re-Loading the Stove....................................23 Dimensions.......................................................6 Overnight Burn...............................................23 Emissions.........................................................6 Normal Operating Sounds............................23 Packing List......................................................7 Hints for Burning ...........................................24 Planning the Installation..................................7 Selecting Wood..............................................24 Preparation for Installation....................................7 Why Dry Wood is Key.... .... .... . ... .. .............24 Additional Accessories Needed for Installation.....7 Wood Cutting and Storage..................................24 Stove Installation Considerations....................... .7 Do Not Burn List.. .. ...........................................25 Floor Protection Requirements......................8 Troubleshooting.............................................26 Stove Placement Requirements.....................8 Daily Maintenance (while stove is in use)...27 Clearances.................. ..............8 Remove Ash(if necessary) . ..........................27 ........................ Top View-Straight Installation..................... ......9 Clean the Glass(if necessary)............................27 Top View-Corner Installation...............................9 Monthly Maintenance (while appliance is in Chimney Connector Requirements..............10 use)..................................................................28 Chimney Requirements.................................11 Door and Glass Inspection..................................28 Chimney Termination Requirements...........12 Creosote-Formation and Need for Removal.....28 Yearly Maintenance.......................................29 Outside Air Requirements.............................12 Touch-Up Paint... .. . ... Alcove Installation Requirements................13 Cleaning the Air Duct and Blower(if applicable).29 Mobile Home Requirements..........................14 Firebrick and Baffle Inspection............................29 Standard Ceiling with a Factory Built Chimney ..15 Door Parts.......................................................30 Cathedral Ceiling with a Factory Built Chimney..15 Replacing the Glass .............. Exterior Factory Built Chimney .. ... ........ .........16 Replacing the Door Gasket.................................30 Hearth Stove Positive Connection ......................16 Replacing the Door Handle................................ 30 Hearth Stove Direct Connection..........................17 Firebox Parts..................................................31 Interior or Exterior Masonry Chimney.................17 Floor and Side Firebrick Removal&Replacement31 Safety Notice..................................................18 Baffle Removal & Replacement....................32 Before Your First Fire....................................18 Air Tube Removal & Replacement...............32 Verify the Installation...... _ __ _ 18 ListingLabel................................................ ......34 Curing the Paint.... ......................... ............_...18 Carbon Monoxide(CO) Emissions......................18 Door Shell Installation...................................35 Over-Firing the Stove..........................................18 Nickel(Cast Iron) Doors Only.............................35 Opening the Door...........................................19 Stove Leg Installation....................................37 Bypass Operation ..........................................19 Pedestal (Part#99200106)............................38 Starting a Fire.................................................20 Using Outside Air with the Pedestal....................38 Adjusting the Burn Rate................................21 Outside Air Boot Installation (Part number Approximate Air Control Settings........................21 99200134)........................................................39 ©Travis Industries 100-01334 4131122 Precautions4 Safety The viewing door must be Gasoline or other flammable closed and latched during liquids must never be used to i operation. start the fire or"Freshen Up"the Smoke from this appliance may fire. Do not store or use active a smoke detector when as gasoline or other flammable the door is open. liquids in the vicinity of this Never block free airflow through appliance. the air vents on this appliance. This appliance is designed and Ashes must be disposed in a approved for the burning of cord metal container with a tight lid wood only. Do not attempt to and placed on a non- burn any other type of fuel other combustible surface well away than cord wood in this ASHE from the home or structure. appliance, it will void all warranties and safety listings. Do not touch the appliance while Keep furniture, drapes, curtains, it is hot and educate all children wood, paper, and other of the danger of a high- combustibles a minimum of 36" temperature appliance. 'young away from the front of the children should be supervised 36" appliance. when they are in the same room as the appliance. This appliance must be properly Contact your local building installed to prevent the officials to obtain a permit and possibility of a house fire. The information on any installation instructions must be strictly restrictions or inspection adhered to. Do not use pk requirements in your area. makeshift methods or Notify your insurance company compromise in the installation. of this appliance as well. Inspect the chimney connector and chimney at least twice This appliance must be monthly and clean if necessary. — 0 connected to a listed high Creosote may build up and Type Clay temperature(UL 103 HT) cause a house fire. HT Liner residential type chimney or an Do not connect this appliance to approved masonry chimney with any chimney serving another a standard clay tile, or stainless appliance. steel liner. 0 Travis Industries 100-01334 4131122 Safety Precautions 5 When installed in a mobile home, this appliance must be - Do not place clothing or other bolted to the floor, have outside I flammable items on or near this Mobile air, and not be installed in the appliance. bedroom(Per H.U.D. Home requirements). Check with local building officials. Never try to repair or replace This wood heater has a any part of this appliance unless manufacturer-set minimum low instructions are given in this = burn rate that must not be manual. All other work must be altered. It is against federal done by a trained technician. Q regulations to alter this setting or Do not make any changes or otherwise operate this wood modifications to an existing heater in a manner inconsistent masonry fireplace or chimney to with operating instructions in this install this appliance. manual. Allow the appliance to cool before carrying out any Over-firing the appliance may maintenance or cleaning. cause a house fire. If a unit or chimney connector glows, you are over-firing. Maintain the door and glass seal Do not use a grate or other and keep them in good device to elevate the fire off of condition. the firebox floor. Burn the fire Do not operate this heater with directly on the bricks. broken or missing glass. Avoid placing wood against the glass when loading. Do not slam the door or strike the glass. Do not throw this manual away. Travis Industries, Inc. grants This manual has important no warranty, implied or Manual operating and maintenance stated,for the installation or instructions that you will need at maintenance of your a later time. Always follow the appliance, and assumes no instructions in this manual. responsibility of any This consequential damage(s). Smoke and CO Detectors: Make sure your home has a working smoke detector,especially near any bedrooms. We recommend having a smoke and/or CO detector in the same room as the wood heater for additional safety. Proposition 65 Warning: Fuels used in gas,woodburning or oil fired appliances, and the products of combustion of such fuels, contain chemicals known to the State of California to cause cancer, birth defects and other reproductive harm California Health &Safety Code Sec.25249.6 ©Travis Industries 100-01334 4131122 Stove • qualified installers only) Installation Options Features • Freestanding 2.2 Cubic Foot Firebox Volume(62 Liter) Freestanding in an Alcove Single Operating Control • Freestanding in a Mobile Home Accepts Logs Up to 18" Long (457mm) • Freestanding Hearth Stove Steel Plate Construction (5/16" &3/16") (8mm & 10mm) • Heavy Duty refractory Firebrick • Optional High-Tech Blower Heating Specifications Approximate Maximum Heating Capacity(in square feet)" 1,200 to 2,000 Maximum BTUs per Hour(Cord Wood Calculation) 72,400 Maximum Burn Time Up to 10 Hours "Heating capacity will vary depending on the home's floor plan, degree of insulation, and the outside temperature. It is also affected by the quality and moisture level of the fuel. This model was not tested for efficiency however it is assigned a default efficiency of 63% by the EPA under previous subpart AAA. Efficiency of this wood heater will be affected by the operational burn rate and the moisture content of the wood used as fuel. Dimensions 23-1/2" / 24"610mm 597mm 5-3/4"146\ " 6"152mm o 1-3/4"44mm Note: Measure side,corner,and back clearances from the stove top Measure front clearances from the stove face. Height: Sculptured or Cast Legs 30-5/8"778mm Pedestal 34-5/8"879mm Weight:448 Lbs. 203 Kilos Figure 7 Emissions This heater meets the 2015 U.S. EPA's crib wood emission limits for wood heaters sold after May 15, 2015. Tested to Method 28, 5H this heater has been shown to deliver heat at rates ranging from 9,300 to 42,200 BTU/hr and an emission value of 1.9g/h. ©Travis Industries 100-01334 4131122 Stove • n (for qualified installers only) SAFETY NOTICE: Please read this entire manual before you install and use your new room heater. Failure to follow instructions may result in property damage, bodily injury, or even death. Contact local building or fire officials about restrictions and installation inspection requirements in your area. Packing List • Wood moisture meter • Bypass tool Planning the Installation ® We suggest that you have an authorized Travis Industries dealer install your stove. If you install the stove yourself, your authorized dealer should review your installation plans. eCheck with local building officials for any permits required for installation of this stove and notify your insurance company before proceeding with installation. ® The location of your wood heater in your home will decide how affectively the heat produced will spread throughout your house. Attention to the home design with consideration of natural convection and air circulation should be taken into account when choosing the placement of your heater within the home. Preparation for Installation • Check for damage to the exterior of the stove(dents should be reported, scratches can be fixed by applying touch up paint). • Check the interior of the firebox(replace cracked firebrick and make sure baffle is in place). ® The stove can be lightened by removing the firebricks and baffle(page 31)-replace before operation. Additional Accessories Needed for Installation • Door Shell 1 Old Part#(includes ashlip trim) New Part#(no ashlip trim) Small Black 99300195 96100634 Small Brass 99300196 96100635 Small Pewter 99300197 96100636 • Legs or Pedestal Stove Installation Considerations The table below details the six most common types of installations and the considerations for each type. Alternative methods of installation are available if they comply with local building codes. Installation Type Considerations Standard Ceiling with a Factory Built Chimney Requires ceiling and roof penetration (Page 15) Provides best draft Cathedral Ceiling with a Factory Built Chimney Cathedral style chimney support required (Page 15) Provides best draft Exterior Factory Built Chimney Uses two elbows to route chimney outside (Page 16) Exterior chimney is hidden from the room • Elbows reduce draft • Optional exterior chase reduces cold air blockage Hearth Stove Positive Connection Utilizes existing masonry or zero clearance(metal)chimney (Page 16) Provides good draft due to full reline • Easier to clean than direct or horizontal hearth stove Hearth Stove Direct Connection Utilizes existing masonry or zero clearance(metal)chimney (Page 17) Requires construction of a"block-off plate" • Draft reduced due to elbows&chimney cross section Interior Masonry Chimney Utilizes existing masonry chimney(not approved for zero clearance (Page 17) (metal)fireplaces) ©Travis Industries 100-01334 4131122 Stove • n (for qualified installers only) Floor Protection Requirements • Stove must be placed on the Travis Industries legs or pedestal. • Floor protection must extend to the sides, rear, and front of the stove(see"Clearances" below for minimum floor protection). NOTE: When installed with reduced clearance connector, the clearance to the back wall may be less than the floor protection requirement. In this case, the floor protection must extend to the wall. • Floor protection must be non-combustible and at least.018"thick(26 gauge). Stove Placement Requirements /A\ Clearances may be reduced by methods specified in NFPA 211, listed wall shields, pipe shields, or other means approved by local building or fire officials. • Stove must be placed so that no combustibles are within, or can swing within (e.g. drapes, doors), 36" (914mm)of the front of the stove • If the stove is placed in a location where the ceiling height is less than 7'(2134mm), it must follow the requirements in the section "Alcove Installation Requirements" • Must maintain the clearances to combustibles listed below(drywall, furniture, etc.): Clearances • The following clearances must be met(see Figure 2 and Figure 3) Clearance Requirements: Single-wall Connector Reduced Clearance* A Sidewall to stove 15" 381 mm 13" 330mm B Back-wall to stove 15" 381 mm 4 25"** 108mm** C Corner-wall to stove 15" 381 mm 6.5" 165mm D Connector to sidewall 24" 610mm 21.5" 546mm E Connector to back-wall 17.75" 451 mm 6.5" 165mm F Connector to corner-wall 24" 610mm 15" 381 mm G Side&Rear Floor Protector 6" 152mm(US) 6" 152mm(US) 8"200mm(Canada) 8"200mm(Canada) H Front Floor Protector 16"406mm(US) 16"406mm(US) 18"450mm(Canada) 18"450mm(Canada) "Reduced clearance installations require one of the chimneys and connectors listed below: AMERI-TEC model DCC with model HS chimney DURAVENT model DVL with DURATEC or DURA-PLUS chimney GSW Super Chimney Twenty-One connected directly to appliance I.C.C.Excel(2100-2 Can.)(103-HT USA)chimney with HP connector METALFAB model DW connector with TG chimney OLIVER MACLEOD PROVENT model PV connector with model 3103 chimney SECURITY model DP connector with SECURITY model ASHT or S2100 chimney SELKIRK METALBESTOS model DS connector with model SSII chimney Standard Masonry Chimney with any one of the above listed connectors NOTE:Reduced clearance connectors may not connect to the flue collar—an appliance adapter may be required. **If using the optional GreenStart Igniter, 6" (153mm)clearance is required to allow for igniter installation. NOTE: Reduced clearance connectors may not connect to the flue collar, an appliance adapter may be required. NOTE: Mobile home installations must use the reduced clearance connector and clearances listed above. NOTE: Standard residential installations with reduced clearance connector may use the"Connector to Wall" clearance determined by the connector manufacturer if approved by local code. This clearance is established by the connector manufacturer and falls under the connector manufacturer's listing. "Stove to Wall"clearances must always be met. 0 Travis Industries 100-01334 4131122 Stove • n (for qualified installers . • Top View - Straight Installation e b OMeasure rear and side clearances from the I 24°610mm t l nearest edge of the stove top. a 5-314"146mm n ONOTE:Vent diameter varies depending on I brand and model. 23-1/2" (D 597mm � Measure front clearances from the face of the stove (unibody). Th k Figure 2 Top View - Corner Installation Oi Measure rear and side clearances from the nearest edge of the stove top. f c 24'610mm g O NOTE:Vent diameter T varies depending on brand and model. 5-si4°lasmm _ ----------- i OMeasure front clearances from the face 597mm j of the stove (unibody). k Figure 3 0 Travis Industries 100-01334 4131122 1 Stove Installationqualified Installers only) Chimney Connector Requirements • Chimney connector is required from the flue collar of the stove to the factory-built chimney or masonry chimney. The chimney connector must be 6"diameter and a minimum 24 gauge black steel, or one of the reduced-clearance connectors listed on page 8. NOTE:Aluminum or galvanized steel is not allowed—these materials cannot withstand the flue temperatures and may give off toxic fumes when heated. NOTE: Standard residential installations may use single-wall connector(Mobile-Homes may not). • The chimney connector may not pass through a ceiling, attic, roof, closet, or any other concealed space(use listed UL 103 HT chimney—see"Chimney Requirements for details). DO NOT USE CONNECTOR PIPE AS CHIMNEY. • IN CANADA;Where passage through a wall or partition of combustible construction is desired, the installation shall conform to CAN/CSA-13365, Installation Code for Solid-Fuel-Burning Appliances and Equipment. • The chimney connector should be as short and direct as possible. No more than 1800 of elbows(two 900 elbows, or two 45'&one 90'elbow, etc.) may be used for the entire system (connector and chimney).. Horizontal runs should slope upwards 1/4"per foot and be a maximum 36" long. • The chimney connector must be installed with the crimped end pointing downwards. This prevents creosote from leaking to the exterior of the pipe. • The chimney connector must be fastened to the stove and each adjoining section (and chimney). • Standard residential installations may use single-wall connector(Mobile-Homes may not • Standard residential installations with reduced clearance connector may use the clearance determined by the manufacturer of the connector for the connector to wall clearance or the clearance listed in this manual. Offsets must be used to maintain the stove to wall clearance. Mobile homes must use the clearances listed in this manual under"Additional Requirements for Mobile Home Installations". ©Travis Industries 100-01334 4131122 I i 1 _ V1 A a z p 0 °� 3 w o. � Q •• o r, �G fA Z O w O a r' z 0-4 p W - W H w Gil Q Q a W pW .aa o F CDQ 3 54 Ox Q z p O p � w 0 m � Z 3 � w zW < UC7Cp O � p A Ln ccra F" Oa Ln mp Q Q _� Fz M a � V W F r O Q w 0 N U M m Cl. z NO w em) CQ Oda A OF w zrxCa Q w x p a paQ! aU 3 ¢ a AQo � aoOm F 14zaz zF w . � z aw . ax r\�a ] z �_ F a z a � H � o 3 wo ZCA � ¢ x Zz Q A Q w OF zaa p fs' 0�. CD z ¢ o z z � Ouam. vFi Ov ¢ Ov Z ❑ ❑ a' E" ❑ ❑ ❑ ❑ ❑ ❑ zm n CITY OF ARLINGTON 238 N. OLYMPIC AVE - ARLINGTON, WA. 98223 PHONE; (360)403-3551 BUILDING PERMIT Address:19721 47th Avenue NE Permit#:2172 Parcel#:00564600000401 Valuation:0.00 OWNER APPLICANT CONTRACTOR Name:CLUER CHRISTOPHER Name:Craft Stove Name:CRAFT STOVE INSTALLATIONS Address: 19721 47TH AVENUE NE Address:900 W Division Address:900 W DIVISION City,State Zip:ARLINGTON,WA 98223 City,State Zip:Mount Vernon,WA 98273 City,State Zip:MOUNT VERNON,WA 98273 Phone: Phone:360-336-2532 Phone:360-336-2532 MECHANICAL CONTRACTOR PLUMBING CONTRACTOR Name:CRAFT STOVE INSTALLATIONS Name: Address:900 W DIVISION Address: City,State,Zip:MOUNT VERNON,WA 98273 City,State,Zip: Phone:360-336-2532 Phone: LIC#: EXP: LIC#: EXP: JOB DESCRIPTION PERMIT TYPE: Residential Mechanical CODE YEAR: 2015 STORIES: CONST.TYPE: DWELLING UNITS: 1 OCC GROUP: BUILDINGS: 1 OCC LOAD: PERMIT APPROVAL I AGREE TO COMPLY WITH CITY AND STATE LAWS REGULATING CONSTRUCTION AND IN DOING THE WORK AUTHORIZED THEREBY; NO PERSON WILL BE EMPLOYED IN VIOLATION OF THE LABOR CODE OF THE STATE OF WASHINGTON RELATING TO WORKMEN'S COMPENSATION INSURANCE AND RCW 18.27. THIS APPLICATION IS NOT A PERMIT UNTIL SIGNED BY THE BUILDING OFFICIAL OR HIS/HER DEPUTY AND ALL FEES ARE PAID. IT IS UNLAWFUL TO USE OR OCCUPY A BUILDING OR STRUCTURE UNTIL A FINAL INSPECTION HAS BEEN MADE AND APPROVAL OR A CERTIFICATE OF OCCUPANCY HAS BEEN GRANTED. IBCI IO/IRC110. SALES TAX NOTICE:Sales tax relating to construction and construction materials in the City of Arli In e reported on your sales tax return form and coded City of Arlington#3101. Signature Print Name Date Released By Dat CONDITIONS INSTALL PER MANUFACTURER'S INSTALLATION SPECIFICATIONS. THIS PERMIT AUTHORIZS ONLY THE WORK NOTED.THIS PERMIT COVERS WORK TO BE DONE ON PRIVATE PROPERTY ONLY. ANY CONSTRUCTION ON THE PUBLIC DOMAIN(CURBS,SIDEWALKS,DRIVEWAYS,MARQUEES,ETC.)WILL REQUIRE SEPARATE PERMISSION. PERMIT FEES Date Description Fee Amount 9/24/2018 Mechanical Fee(Enter Fixture Fee) $25.00 9/24/2018 Mechanical Permit Base Fee $25.00 9/24/2018 Processing/Technology Fee $25.00 Total Due: $75.00 Total Payment: $0.00 Balance Due: $75.00 CALL FOR INSPECTIONS BUILDING(360)403-3417 When calling for an inspection please leave the following information: Permit Number,Type of Inspection being requested,and whether you prefer morning or afternoon Permit#2172 Address Payment Info Address 19721 47TH AVE NE Receipt# 1207572 City ARLINGTON Date 12/4/2018 State WA Paid By Mary K Sousa Zip 98223-7765 Description 72895106 Payment Type cc Accepted By Raelynn Jones Fees Paid Total Amount Fee Fee Description Factor Fee Paid Amount Mechanical Fee(Enter Fixture Fee) 322.10.00.00 1 25.00 25.00 Mechanical Permit Base Fee 322.10.00.00 0 25.00 25.00 Processing/Technology Fee 341.43.00.02 0 25.00 25.00 Total Payment:75.00 Permit#: 2172 Permit Date: 09/24/18 Permit Type: RESIDENTIAL MECHANICAL Project Name: Cluer Applicant Name: Craft Stove Applicant Address: 900 W Division Applicant, City, State, Zip: Mount Vernon,WA 98273 Contact: Dawn Sousa Birch Phone: 360-336-2532 Email: craftstoveswash@comcast.net Scope of Work: Install free standing wood stove Valuation: 0.00 Square Feet: 0 Number of Stories: 0 Construction Type: Occupancy Group: ID Code: Permit Issued: 12/04/2018 Permit Expires: Form Permit Type: Status: IN PROCESS Assigned To: Launa Black Property Parcel# Address Legal Description Owner Name Owner Phone Zoning 00564600000401 19721 47TH AVE NE CLUER 111 Single Family CHRISTOPHER Residence-Detached Contractors Contractor Primary Contact Phone Address Contractor Type License License# CRAFT STOVE 360-336-2532 900 W DIVISION CONSTRUCTION Labor& CRAFTSI831CH INSTALLATIONS CONTRACTOR Industries Inspections Date Inspection Type Description Scheduled Date Completed Date Inspector Status 09/04/2019 R04.PLUMBING 09/05/2019 BUILDING Completed GROUNDWORK Plan Reviews Date Review Type Description Assigned To Review Status 09/24/2018 RESIDENTIAL BUILDING MECHANICAL Fees Fee Description Notes Amount Mechanical Fee(Enter Fixture Fee) $25.00 Mechanical Base Permit Fee $25.00 Processing/Technology $25.00 Total $75.00 Attached Letters Date Letter Description 09/24/2018 Building Permit Payments Date Paid By Description Payment Type Accepted By Amount 12/04/2018 Mary K Sousa 72895106 cc Raelynn Jones $75.00 Outstanding Balance $0.00 Uploaded Files Date File Name 01/06/2020 6055114-2172 9-5-19IC.pdf 09/24/2018 3974203-19721 Residential Mechanical D8GcVLPVwpY7SV.pdf 09/24/2018 3974204-19721 attachments C015031000017664943 cgUvlSg6SH6VVN3u4uXCz 100-01334.pdf