Loading...
HomeMy WebLinkAbout17218 84th Ave Ne_25-0002_2025 RESIDENTIAL PLUMBING APPLICATION Community and Economic Development City of Arlington • 18204 59th Ave NE • Arlington, WA 98223 • Phone (360) 403-3551 This application is for new, repaired, altered or replaced plumbing installation for existing residences. Please fill out all pages of this application and include all information. The City of Arlington does not require a permit to stop leaks or clear stoppages, unless the piping is repaired, altered or replaced. Type of Permit:  New Installation  Addition  Alteration  Repair Property Address: 17218 84TH AVE NE Project Valuation: 8059 Lot #: - Parcel ID No.: 01089200002300 Preferred Contact:  Owner  Contractor Project Description: TANKLESS SWAP Owner Name: HO VAN HIEN Home No.: - Email Address: billing@sevynpm.com Cell No.: 4255276556 Mailing Address: 18109 3RD DR SE City: BOTHELL State: WA Zip: 98012 Contractor Name: CM HEATING Office No.: 4252590550 Email Address: PERMITS@CMHEATING.COM Cell No.: - Mailing Address: 1500 INDUSTRY ST #200 City: EVERETT State: WA Zip: 98203 L&I Contractor License Number: CMHEAHL750LP Expiration Date: 6/30/2026 • All hose bibs required to be equipped with Atmospheric Vacuum Breakers per ASSE 1019 • All water supplies at 80psi or greater shall have Pressure Reducing Valves (PRV) • Cross-Connection-Control may be required Proposed Interior Water Piping Size:  ½”  ⅝”  ¾”  1” Proposed Interior Piping Material:  CPVC  Brass  Copper  PEX-AL-PEX  PEX  Galvanized Steel  Other Proposed Exterior Water Piping Size:  ½”  ⅝”  ¾”  1”  1½”  2” Proposed Exterior Piping Material:  PVC  PE  Copper  PEX-AL-PEX  PEX-AL-PE  PEX  Other Proposed Drain-Waste-Vent (DWV)  Schedule 40 ABS DWV  Copper  Galvanized Steel  Cast Iron Material:  Schedule 40 PVC DWV  Brass  Other Proposed Drain-Waste-Vent (DWV)  ½”  ⅝”  ¾”  1”  1½”  2”  3” 4” Piping Size: Residential plumbing permits will be assessed a base fee, fee per unit, and inspection fee (plan review fee per Table 4-6 may be required for certain permits) Type of Fixture No. of Fixtures Cost per Fixture Subtotal Additional Plan Review fees x $ 75.00 = Alteration/repair piping x $ 15.00 = Backflow Assembly x $25.00 = Base Plumbing Fee 1 x $ 25.00 = $25.00 Bath/Shower Combo x $ 15.00 = Building Main Waste x $ 25.00 = Clothes Washer x $ 15.00 = Dishwasher x $ 15.00 = REV03.2022 Page 1 of 2 Residential plumbing permits will be assessed a base fee, fee per unit, and inspection fee (plan review fee per Table 4-6 may be required for certain permits) Drinking Fountain x $ 15.00 = Floor Drains x $ 15.00 = Grease Interceptor x $ 75.00 = Grease Trap x $ 25.00 = Hose Bibb x $ 15.00 = Icemaker/Refrigerator x $ 15.00 = Irrigation – per meter x $ 25.00 = Kitchen Sink & Disposal x $ 15.00 = Laundry Tray x $ 15.00 = Lavatory x $ 15.00 = Medical Gas Piping ≤ 5 Inlets / Outlets x $ 60.00 = Medical Gas Piping for each additional Inlet / x $ 5.00 = Outlet > 5 Miscellaneous – regulated by plumbing code, not x $ 15.00 = otherwise specified Pretreatment Interceptor x $ 15.00 = Re-inspection Fee x $ 75.00 = Roof Drains x $ 15.00 = Shower (only) x $ 15.00 = Sink (bar, service, etc.) x $ 15.00 = Toilets x $ 15.00 = Urinal x $ 15.00 = Vacuum Breakers x $ 25.00 = Water Heater x $ 25.00 = MODEL NO.: Water Heater – Tankless x $ 25.00 = 1 25 MODEL NO.: Permit Fee 25 Inspection Fee $75.00 Processing/Technology Fee $25.00 Total I hereby certify that the above information is correct and that the construction on, and the occupancy and the use of the above-described property will be in accordance with the laws, rules and regulation of the State of Washington. SABRINA KENNARD 10/27/25 Signature Print Name Date FOR STAFF USE ONLY PERMIT # ACCEPTED BY: DATE STAMP REV02.2024 Page 2 of 2               !"#$% &'()'%*!+, -./0  #1# #2 3!+%'$%, 45+# 3!+% '$%!  !"#$% 6#7$ *8%*!+, 9: ;  45+# <'=#, >? @AB >CDB E!=# <!F, G H='*( I22 #77, JKLLKMNOPQRSMTUVWXU 3#(( <!F, YZ//Z[\//\ ]'*(*+^ I22 #77, _-_.0 `ab ba cC 3*%d, e?f>Cgg h%'%#, iA j*8, 0-._Z  ;   *=' d 3!+% '$%! , kl >CAfDBm 411*$# <!F, YZ/Z/0.//. H='*( I22 #77, nCalDfcOkl>CAfDBmVk? 3#(( <!F, G ]'*(*+^ I22 #77, _/.. DBbocfap cf qZ.. 3*%d, C@CaCff h%'%#, iA j*8, 0-Z.` rst 3!+% '$%! r*$#+7# <)=u# , kl>CAg[/_gi Hv8* '%*!+ 6'%#, \w`.wZ.Z\  !8!7#2 t+%# *! x'%# *8*+^ h*y#, z{|} ~{} €{} z}  !8!7#2 t+%# *! *8*+^ ]'%# *'(, 3&3 ‚ '77                    ! "#! $%! !  ! !      &    '          (   ' )('*&    + , %-.('        /  + , %-'(' .      (   ' )('*    ! "#! $%! !  ! ! $! %! 0    ,12 132     2  4 54  ,5  +4 )    34  6 2 %71 82  9, 4 +   1* 68 4:, ;<4=   0  34                             ! "   ! # $  " %  "  &   '   ( NPE-2 Series Tankless Water Heaters Premium Condensing Tankless Gas Water Heater Specification Sheet Certified design according to the latest ANSI Z21.10.3 - CSA 4.3 standards for both indoor and outdoor installations (with optional Outdoor Vent Kit) Compatible with 1/2" gas pipe up to 24 ft* equivalent length (*see Installation Manual for additional information) Compatible with 2" PVC vent up to 75 ft** and 3" Vent up to 150 ft** (**with no elbows) Gas Type Designed for use in Residential and Commercial applications Recirclation/ Main/Sub (see Space Heating below for available models and warranty terms) Flow Rate/Status Temperature Setting Gas Input Range Combustion/erroeCombustion/Error NPE-150S2 - 120,000 to 18,000 BTU/h NPE-180A2/S2 - 150,000 to 10,000 BTU/h Menu Button Up Button NPE-210A2/S2 - 180,000 to 12,000 BTU/h Back Button Down Button NPE-240A2/S2 - 199,900 to 13,300 BTU/h OK Button Hot Water Flow Rate Capacity (*based on 35°F temperature rise) NPE-150S2 - 6.8 GPM NPE-180A2/S2 - 8.4 GPM NPE-210A2/S2 - 10.1 GPM Certified Design Compatible with Multi-Line Control NPE-240A2/S2 - 11.2 GPM 2” PVC and 1/2” Gas Pipe Panel with Diagnostics TDR (Turndown Ratio) up to 15:1 Dual Primary and Secondary Stainless Steel Heat Exchangers for optimum efficiency and durability Built-In Advanced Multi-Line Control Panel with Setup Wizard allows adjustment of temperature settings and displays of Indoor and Outdoor operating status and error codes Venting Options TMTechnology - NPE-A2 models come with 2” Intake Cap built-in 0.5 gallon Buffer Tank and Recirculation Pump to provide 2" Coupling maximum hot water comfort (NaviCirc Crossover Valve optional) 2" Pipe Outdoor INTELLIGENT Preheating - recognizes hot water usage patterns to Vent Cap intelligently provide hot water to fixtures when needed Temperature Options - available temperature settings for Residential applications range from 97°F p to 140°F with high- temperature Commercial mode capable of up to 185°F Ready-Link Cascade Compatible for up to 32 units for increased hot water production Non-Direct Vent (Indoor) Non-Direct Vent (Outdoor) Common Vent Compatible - allows for cascade systems to use a Direct Vent (Indoor) single exhaust and/or intake pipe for up to 12 units with the use of the Common Vent Backflow Damper Collar Kit (#30014367A) Compatible with Wi-Fi Control (#PBCM-AS-001) Freeze Protection - maintains normal operation in cold weather * NPE-150S2 conditions when the unit is installed INDOORS and connected to power. Excluded For OUTDOOR installations: the ambient temperature at the installation location must be above 32°F (0°C) and below 125°F (52°C) Note Refer to the Installation Manual for additional Freeze Protection guidelines Uniform Energy Factor (listed models for use with Natural Gas and Propane) NPE-150S2 - 0.93 UEF NPE-180A2/210A2/240A2 - 0.95 UEF NPE-180S2/210S2/240S2 - 0.96 UEF Job Name: _____________________________________________ Compatible for use with Natural Gas (NG) and Propane (LP) Gas*** (*** requires installation of included Gas Conversion Kit by a qualified gas servicer) Location: ______________________________________________ Approved for installations on Manufactured Homes Engineer: _____________________________________________ Certified by CSA Group, NSF 5 and 372 Low Lead, AHRI Certified, SCAQMD Wholesaler: __________________________________________ (Rule 1146.2 Type 1 - Complies with 14 ng/J or 20 ppm NOx @ 3% O2) Contractor: ___________________________________________ Limited Warranty - 15-Year Heat Exchanger and 5-Year Parts (Residential)**** Model No.: _____________________________________________ 8-Year Heat Exchanger and 5-Year Parts (Commercial)**** Submitted to: _________________________________________ (**** full details of warranty terms available in the Navien manuals or website) Optional Accessories are available (see below) Condensate Neutralizer Plumb Easy Valve Set (3/4") Ready-Link 3" Vent Termination Remote Controller (GXXX001322 - Single Unit) NPE-2 Outdoor Vent Kit External Pump Wire (30009323A - Lead Free) Communication Cable Caps and Wall Flanges (30022717B) (GXXX001324 - Up to 6 Units) (30025801A) (GXXX001319) (30025812A - for Pipe Cover) (GXXX000546) (GXXX3873B) (GXXX001325 - Up to 16 Units) 1-NPE2-SS-001-1.1 NPE-2 Series Tankless Water Heaters Premium Condensing Tankless Gas Water Heater Front View Item NPE-150S2* NPE-180A2 NPE-180S2 NPE-210A2 NPE-210S2 NPE-240A2 NPE-240S2 Heat Capacity Natural Gas, 18,000-120,000 10,000-150,000 BTU/H 12,000-180,000 BTU/H 13,300-199,900 BTU/H (Input) Propane Gas BTU/H Uniform UEF (for NG & LP) 0.93 0.95 0.96 0.95 0.96 0.95 0.96 Energy Factor mm) 35 °F (19 °C) 6.8 GPM 8.4 GPM (32 L/m) 10.1 GPM (38 L/m) 11.2 GPM (42 L/m) (695 Temp Rise (25.8 L/m) (731 mm) 28.8 in27.4 in Flow Rate 45 °F (25 °C) 5.3 GPM 6.5 GPM (25 L/m) 7.8 GPM (30 L/m) 8.7 GPM (33 L/m) (DHW) Temp Rise (20 L/m) 67 °F (36 °C) 3.4 GPM 4.3 GPM 4.4 GPM 5.1 GPM 5.3 GPM 5.6 GPM 5.8 GPM Temp Rise (13 L/m) (16 L/m) (17 L/m) (19 L/m) (20 L/m) (21 L/m) (22 L/m) Dimensions 17.3 in (W) x 27.4 in (H) x 13.2 in (D) 62 lbs 73 lbs 68 Ibs 77 Ibs 73 lbs 77 Ibs 73 lbs Weight (28 kg) (33 kg) (31 kg) (35 kg) (33 kg) (35 kg) (33 kg) Installation Type Indoor or Outdoor Wall-Hung Venting Type Forced Draft Direct Vent Overhead View A B Ignition Electronic Ignition 10 mm) Water Pressure 15-150 PSI 1.5 in (38 mm) 14.3 in (364 mm) 0.4 in ( mm) Natural Gas Supply Pressure mm) (67 3.5 in WC-10.5 in WC 77 2.6 in (from source) in ( 3 Propane Gas Supply Pressure 8 in WC-13in WC (from source) 4.5 in (115 mm) 6.7 in (170 mm) Natural Gas Manifold Pressure –0.04 in WC - –0.03 in WC - –0.55 in WC –0.03 in WC - –0.76 in WC –0.03 in WC - –0.96 in WC (min-max) –0.40 in WC Propane Gas Manifold Pressure –0.03 in WC - –0.02 in WC - –0.55 in WC –0.02 in WC - –0.76 in WC –0.02 in WC - –0.96 in WC (min-max) –0.40 in WC Minimum Flow Rate 0.5 GPM (1.9 L/m), < 0.01 GPM (0.04 L/m) option for “A2” models** Supply Connections 3/ C D E F G Cold Water Inlet 4 in NPT Description Diameter Connection Hot Water A Air Intake 2 in Sizes Outlet 3/4 in NPT B Exhaust Gas Vent 2 in (731 mm) Gas Inlet 3/ 3 in 4 in NPT C Hot Water Outlet /4 in 28.8 Main Supply 120 V AC, 60 Hz D Gas Inlet 3/4 in 336 mm) E Recirculation Inlet 3/4 in 13.2 in ( Maximum mm) mm) Power Supply (166 61 mm) 61 Power 200 W (max 2 A), 350 W (max 4 A) with external pump connected F Condensate Outlet 1/ in in ( 2 in 6.5 2.4 in ( 2.4 Consumption G Cold Water Inlet 3/ 4 in 2.3 in (60 mm)3.0 in (77 mm) 8.3 in (212 mm) Casing Cold Rolled Carbon Steel 17.3 in (440 mm) Materials Heat Primary Heat Exchanger: Stainless Steel Exchangers Secondary Heat Exchanger: Stainless Steel NPE-180A2 / 210A2 / 240A2 2 in or 3 in PVC, CPVC, Approved Polypropylene and stainless steel Exhaust 2 in or 3 in Special Gas Vent Type BH (Class II, A/B/C) Supply Connections Venting Intake 2 in or 3 in PVC, CPVC, Approved Polypropylene and stainless steel Description Diameter C D E F 2 in or 3 in Special Gas Vent Type BH (Class II, A/B/C) A Air Intake 2 in Vent Clearances 0 in to combustibles B Exhaust Gas Vent 2 in High Elevation 10,100 feet for both NG or LP gas. Please refer to Installation Manual for additional details and instructions. C Hot Water Outlet 3/ 4 in D Gas Inlet 3/ Flame Rod, APS, Ignition Operation Detector, Water Temperature High Limit Switch, Exhaust Temperature High Limit Sensor, 4 in Safety Devices E Condensate Outlet 1/2 in 13.2 in (336 mm) mm) Power Surge Fuse, Burner High Limit Fuse, Vent Installation Detector (VID) (166 mm) F Cold Water Inlet 3/ 6.5 in in (61 4 in 2.4 in (61 mm) 2.4 * NPE-150S2 model not certified by EnergyStar ** Available for “A2” models configured in an optional ComfortFlow recirculation mode. Energy consumption will increase when the system is 2.3 in (60 mm) 11.3 in (289 mm) configured for recirculation. 17.3 in (440 mm) NPE-150S2 / 180S2 / 210S2 / 240S2 Gas-fired, tankless, condensing, wall-mounted water heater(s) shall be direct vent NPE-2 Series models as manufactured by Navien, Inc. and are certified by CSA Group to the latest edition of ANSI Standard Z21.10.3-CSA 4.3. Water heater(s) shall have a 15(5)-year limited Heat Exchanger warranty and 5(3)-year limited Parts warranty (8(5)-year Heat Exchanger and 5(3)-year Parts for Commercial use) per Navien Limited Warranty. Unit(s) shall be designed to burn natural gas and can be for use with propane when a Gas Conversion Kit is installed. ________ (qty). NPE water heater(s) shall have a nominal flow rate capacity of ________ GPM/GPH at ________°F rise with rated input of _____________ BTU/hr. Water heater(s) shall be vented with 2“ Schedule 40/80 PVC/CPVC, approved polypropylene and stainless steel vent pipe at a distance not to exceed 75’ (or equivalent) with each elbow equal to 8’ of pipe length or 3” Schedule 40/80 PVC/ CPVC, approved polypropylene and stainless steel vent pipe at a distance of 150’ (or equivalent) with each elbow equal to 5’ of pipe length. Water heater(s) is rated for 150 PSI working water pressure and 300 PSI test pressure. Gas supply pressure shall be 3.5" to 10.5” WC for natural gas and 8.0“ to 13.0” WC for propane. Unit(s) shall have a steel case, dual stainless steel heat exchangers, eco premixed burner, negative pressure gas valve, dual venturi, 3/4” inlet gas connection, 3/4” brass inlet/outlet water connections, water holding capacity of 0.6 gallons for the NPE-150S2, 1.0 gallon for the NPE-180A2 model (0.7 gallons for NPE-180S2 model), 1.2 gallons for the NPE-210A2/NPE-240A2 models (0.7 and 0.9 gallons for NPE-210S2 and NPE-240S2 models respectively), and a condensate collector. The NPE-180A2 model weighs 73 lbs (NPE-180S2 weighs 68 lbs), and the NPE-210A2/NPE-240A2 models weigh 77 lbs (NPE-210S2 and NPE-240S2 weigh 73 lbs) and the NPE-150S2 weigh 62lbs. Unit(s) shall include features such as an adjustment for installations at high elevation, temperature lockout, and temperature options from 97-120°F in 1°F intervals and 120-140°F in 1°F intervals. The unit(s) shall include additional temperature options of 140-185°F in 1°F intervals, for high temperature commercial applications. All NPE “A2” models shall include an internal circulation pump and 0.5-gallon buffer tank. The water heater(s) shall be controlled by an internal circuit board that monitors the inlet and outlet temperatures with installed thermistors, sensing and controlling flow rate to set point temperature with air-fuel ratio controls in order to maintain thermal combustion efficiency. Unit(s) shall include safety features such as flame sensor system, high limit sensors, overheat prevention device, freeze protection mode, and fan motor rotation detector. Multi- system (cascade) applications that require 2 to 32 units shall be installed by connecting the units using cable only connections (Ready Link). The water heater(s) exceeds the energy efficiency requirements of ASHRAE 90.1-2010 and is listed by SCAQMD Rule 1146.2 (Type 1) as compliant with Rule 1146.2 (Type 1) for Ultra Low NOx requirements of 14 ng/J or 20 ppm @ 3% O2. * Navien reserves the right to change specifications at any time without prior notice Navien, Inc. 20 Goodyear, Irvine, CA 92618 Ph: (949)420-0420 Fax: (949)420-0430 www.NavienInc.com 1-NPE2-SS-001-1.1 City of Arlington 18204 59th Avenue NE, Arlington, Washington 98223 Phone: 360-403-3551 Invoice Number: 25-0031 INVOICE Invoice Date: October 28, 2025 Account Number: 3384635531 Bill To: CM Heating Invoice Questions? 1500 Industry St #200 Phone: 360-403-3551 Everett, WA 98203 Invoice Due Date: October 28, 2025 Record Number: Permit A25-0033 Parcel Number: 01089200002300 Location: 17218 84TH AVE NE Date Description Paid Date Amount Paid Balance October 28, Processing/Technology (320.341.43.00.02) $25.00 2025 October 28, Plumbing Base Fee (006.322.10.00.01) $25.00 2025 October 28, Inspection $75.00 2025 October 28, Water Heater (Tankless) $25.00 2025 TOTAL: Permit Fees $150.00 $150.00 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- --------------------------------------------------------- REMITTANCE INFORMATION If you are paying by check, please include this portion with your payment and remit to the address listed on this invoice. Remittance Information Invoice Account Total Due Your payment is due by October 28, 2025 This Number Number Invoice 25-0031 3384635531 $150.00 CM Heating 1500 Industry St #200 Everett, WA 98203 City of Arlington 18204 59th Avenue NE, Arlington, Washington 98223 Phone: 360-403-3551 Building Permit Permit #: 25-0002 PERMIT EXPIRES 180 DAYS Parcel: 01089200002300 AFTER DATE OF ISSUANCE. Description of Work: Water Heater Change Out Valuation: 8059 Date Applied: October 29, 2025 Permit Address: 17218 84TH AVE NE OWNER APPLICANT CONTRACTOR CM Heating HO VAN HEIN SABRINA KENNARD 1500 Industry St #200, Everett, WA 98203 17218 84TH AVE NE ARLINGTON, WA, 98223 1500 INDUSTRY ST #200 4252590550 4252590550 permits@cmheating.com billing@sevynpm.com PERMITS@CMHEATING.COM registration_number : CMHEAL751LW Permit Type : Residential - Plumbing Code Year : code_year Stories: 2 Const Type : IRC Building Type VB Dwelling Units : 1 Occupancy Group : R-3 Residential PERMIT APPROVAL The issuance or granting of this permit shall not be construed to be a permit for, or approval of, any violation of this Code or any other ordinance or order of the City, of any state or federal law, or of any order, proclamation, guidance advice or decision of the Governor of this State. To the extent the issuance or granting of this permit is interpreted to allow construction activity during any period of time when such construction is prohibited or restricted by any state or federal law, or order, proclamation, guidance advice or decision of the Governor of this State, this permit shall not authorize such work and shall not be valid. The building official is authorized to prevent occupancy or use of a structure where in violation of this Code, any other City ordinances of this jurisdiction or any other ordinance or executive order of the City, or of any state or federal law, or of any order, proclamation, guidance advice or decision of the Governor. The building official is authorized to suspend or revoke this permit if it is determined to be issued in error or on the basis of incorrect, inaccurate or incomplete information, or in violation of any City ordinance, regulation or order, state or federal law, or any order, proclamation, guidance or decision of the Governor. It is unlawful to use or occupy a building or structure until a final inspection has been made and approval or a Certificate of Occupancy has been granted. This permit authorizes only the work noted and covers work to be done on private property only. Any construction on public domain (curbs, sidewalks, driveways, marquees, etc.) will require a separate permit. The property owner shall ensure that the construction project complies with all applicable zoning codes and regulations. The property owner shall also ensure that the construction project does not cause any adverse impact on the surrounding environment or community. The property owner shall be responsible for obtaining all necessary permits and approvals from the relevant authorities before commencing construction. The property owner shall ensure that the construction project complies with all applicable design review requirements. CONDITIONS 1.) Adhere to approved equipment 2.) Permit shall be onsite for inspections 3.) Call for inspections INSPECTIONS Inspection Line: 360-403-3417 Call for inspections by 3:30 pm for next day inspection. Please allow 48 hours for Fire Inspections. Please provide the following information when leaving a message: Permit Number, Type of Inspection, and provide preference of morning or afternoon inspection. Inspection Portal: Please login to customer portal and submit for the desired inspection type for the permit. Kevin Olander Building Official ASSOCIATED FEES Date Description Paid Date Amount Paid Balance October 28, Processing/Technology (320.341.43.00.02) $25.00 2025 October 28, Plumbing Base Fee (006.322.10.00.01) $25.00 2025 October 28, Inspection (006.322.10.00.01) $75.00 2025 October 28, Water Heater (Tankless) (006.322.10.00.01) $25.00 2025 TOTAL: Permit Fees $150.00 $150.00 Credit/Debit Card 31 Payment Successful October 28, 2025 $150.00 $0.00 Permit Information General Information Permit # 25-0002 Parcel # 01089200002300 Building ID Location 17218 84TH AVE NE Permit Type Residential Permit Use Plumbing Zone Permit # Subdivision Applicant Name SABRINA KENNARD Address 1500 INDUSTRY ST #200 Applicant Email PERMITS@CMHEATING.CO Phone 4252590550 Cell M Owner Name HO VAN HEIN Address 17218 84TH AVE NE ARLINGTON, WA, 98223 Owner Email billing@sevynpm.com Phone Cell Contractor CM Heating Address 1500 Industry St #200, Everett, WA 98203 Contractor Email permits@cmheating.com Phone 4252590550 Cell Property Information Type/Improveme Repair/Replacement Accessory/Struct IBC Building Type V-B nt ure Current Use R-3 Residential Proposed Use Current Zoning RLC Proposed Zoning Project Cost 8059 Project Value 8059 Current Use And Water Heater Change Out Proposed Changes Lot Width Lot Depth Map Number Total Area of Building & Accessory Total Area of All Man-made Improvements Structures (Sq Ft) (Sq Ft) General Notes Restrictions / Variances © Community Development Online Portal Page 1 of 6 December 3, 2025 11:57AM Structure Information Structure Type IRC Building Type VB # of Stories 2 Usable Floor Area (Sq Ft) Structure Height # of Units 1 Load per Floor (Lbs) Sign Dimensions # of Bedrooms 4 # of Bathrooms 3 Occupancy With Chairs Tables & Chairs Empty Room Foundation Foundation Type Footing Depth Material Foundation Information Setbacks Front & 0 0 Setbacks Right & 0 0 Rear Left Sides Setbacks Information Water Utility Public Sewage Utility Public Gas Utility Public Electric Utility Public Driveway Width # of Off Street # of Off Street Parking Loading Miscellaneous Information © Community Development Online Portal Page 2 of 6 December 3, 2025 11:57AM Contractors License # Business Name Type Contact CMHEAL751LW CM Heating General Contractor Permit Coordinator © Community Development Online Portal Page 3 of 6 December 3, 2025 11:57AM Inspections Inspection # Inspection Type Status Date Inspector 25-0033 Residential - Plumbing Pass November 6, 2025 Kevin Olander Final © Community Development Online Portal Page 4 of 6 December 3, 2025 11:57AM Contacts Contact Name Type Project Address Phone SABRINA KENNARD Applicant 1500 INDUSTRY ST #200 425-259-0550 CM Heating Contractor 1500 Industry St #200, 425-259-0550 Everett, WA 98203 HO VAN HEIN Owner 17218 84TH AVE NE ARLINGTON, WA, 98223 SABRINA KENNARD Others 1500 INDUSTRY ST #200 425-259-0550 © Community Development Online Portal Page 5 of 6 December 3, 2025 11:57AM Fees Fee Type Date Debit Credit Balance Permit Fees October 28, 2025 $0.00 $0.00 $150.00 $-150.00 T O T A L $0.00 $150.00 $-150.00 © Community Development Online Portal Page 6 of 6 December 3, 2025 11:57AM Powered by TCPDF (www.tcpdf.org)